2006 DODGE SPRINTER power steering

144 STARTING AND OPERATING
POWER ASSISTANCE STARTING THE ENGINE
Battery charge warning lamp (1)
Engine oil level indicator lamp (2)
WARNING!
When the engine is not running, there is no power
assistance for the brake and steering system. In
this case, it is important to keep in mind that a
considerably higher degree of effort is necessary
to brake and steer the vehicle.

158 STARTING AND OPERATING
Protect sharp edges with padding.
 Check the tire pressures after loading the vehicle.
For passenger vans:
 Do not stack loads higher than the upper edge of the
backrests.
 Always place the load against the backrests of the
seat benches.
 Whenever possible, transport loads behind seats
that are not occupied.
 Distribute the load in such a way that the
permissible axle loads are not exceeded when the
vehicle is equipped with the maximum number of
seats. Loading the luggage compartment up to the
maximum payload would cause the permissible
rear axle load to be exceeded.BRAKES
Service Brake
WARNING!
When the engine is not running, the brake and
steering systems are without power assistance.
Under these circumstances, a much greater effort
is necessary to stop or steer the vehicle.
After driving in heavy rain for some time without
applying the brakes or through water deep
enough to wet brake components, the first
braking action may be somewhat reduced and
increased pedal pressure may be necessary. Be
sure to maintain a safe distance from vehicles in
front.
Resting your foot on the brake pedal will cause
excessive and premature wear of the brake pads.
It can also result in the brakes overheating,
thereby significantly reducing their effectiveness.
It may not be possible to stop the vehicle in
sufficient time to avoid an accident.

176 STARTING AND OPERATING
STEERING
When the engine is not running, there is no power
assistance for the steering. Greater force will be
required to steer the vehicle.
WHEELS AND TIRES
The tires on a new vehicle provide a balance of many
characteristics. They should be inspected regularly for
wear and correct cold tire inflation pressure. The
vehicle manufacturer strongly recommends to use tires
equivalent to the originals in size, quality and
performance when replacement is needed. Refer to the
Tire and Loading Information placard on the driver’s
door B-pillar for the size designation of your tire.
The service description and load identification will be
found on the original equipment tire. Failure to use
equivalent replacement tires may adversely affect the
safety, handling, and ride of your Sprinter vehicle.Contact an authorized Sprinter Dealer or an
authorized tire dealer with any questions you may
have on tire specifications or capability.
CAUTION!
Power take off must not exceed 10 kW. Exceeding
the power take off may cause damage to the
auxiliary drive and/or ribbed V-belt.
WARNING!
Only use tires which have been tested and ap-
proved for your Sprinter vehicle by the vehicle
manufacturer. Tires approved by the vehicle man-
ufacturer are developed to provide best possible
performance in conjunction with the driving safe-
ty systems on your Sprinter vehicle such as ABS or
ESP
®.
Using tires other than those approved by the
vehicle manufacturer may result in damage that is
not covered by Warranty.

200 STARTING AND OPERATING
Tire Ply Material
(1) Plies in sidewall
(2) Plies under tread
NOTE: Data shown on tire are for illustration purposes
only. Actual data on tires are specific to each vehicle
and may vary from data shown in the illustration.
This marking tells you about the type of cord and
number of plies in the sidewall and under the tread.Tire and Loading Terminology
Accessory Weight
The combined weight (in excess of those standard
items which may be replaced) of automatic
transmission, power steering, power brakes, power
windows, radio, and heater, to the extent that these
items are available as factory-installed equipment
(whether installed or not).
Air Pressure
The amount of air inside the tire pressing outward on
each square inch of the tire. Air pressure is expressed
in pounds per square inch (psi), or kilopascal (kPa) or
bars.
Aspect Ratio
Dimensional relationship between tire section height
and section width expressed in percentage.
Bar
Another metric unit for air pressure. There are 14.5038
pounds per square inch (psi) to 1 bar; there are 100
kilopascals (kPa) to 1 bar.

WHAT TO DO IN EMERGENCIES 249
6
*Vehicle Type 2500 onlyIf the Engine is Damaged
For towing distances up to 30 miles (about 50 km)
 Shift gear selector lever to "N" position.
 Do not exceed a towing speed of 30 mph (50 km / h).
For towing distances greater than 30 miles (about
50 km)
 Remove the propeller shafts leading to the drive
axles.
The vehicle can be towed without restriction.
If the Transmission is Damaged
 Remove the propeller shafts leading to the drive
axles.
If the Front Axle is Damaged
 Raise the front axle.
 Observe the same towing restrictions as for engine
damage.
If the Rear Axle is Damaged
 Raise the rear axle.
NOTE: Comply with local legal regulations regarding
towing vehicles.
WARNING!
Do not tow the vehicle if the key cannot be turned
in the ignition lock.
If the key cannot be turned, the ignition lock re-
mains locked and the vehicle cannot be steered.
With the engine not running there is no power
assistance for the braking and steering systems.
In this case, it is important to keep in mind that a
considerably higher degree of effort is necessary
to brake and steer the vehicle.
The vehicle must not be towed with the front axle
raised and the key in position 2 in the ignition
lock as the drive wheels could then lock due to the
acceleration skid control (ASR) or the optional
Electronic Stability Program (ESP
®)*.

MAINTAINING YOUR VEHICLE 297
7
Recommended Fluids and Lubricants
The manufacturer recommends for your vehicle model
the use of DaimlerChrysler approved fluids and
lubricants, e.g. engine oil, gear oil, automatic
transmission fluid, brake fluid, power steering fluid,
coolant and anti-corrosion/anti-freeze fluid only.
WARNING!
Failure to use fluids and lubricants which meet
the standards and specifications described in this
booklet or failure to adhere to the specified re-
placement intervals may result in damage to safe-
ty-related systems of your vehicle, such as the
brake system, which could cause an accident and/
or serious injury to you and others.
Use only fluids and lubricants meeting the
standards and specifications and adhere to
specified replacement intervals.
CAUTION!
Failure to use fluids and lubricants which meet
the standards and specifications described in this
booklet or failure to adhere to the specified
replacement intervals may result in a significantly
shortened service life and/or damage to
components of your vehicle, the repair of which
will not be covered by Warranty.
Use only fluids and lubricants meeting the
standards and specifications and adhere to
specified replacement intervals.

MAINTAINING YOUR VEHICLE 301
7
COMPONENT SERVICE
INTERVALPRODUCT NAME/PRODUCT NUMBER MB
SHEET
Engine Coolant,
Anticorrosion/
Antifreeze Fluid15 years or
160,000 mi
(256,000 km)EURO Peak Coolant/Anti-freeze, OLD WORLD INDUSTRIES
Zerex G05, The Valvoline Company
Zerex G48, The Valvoline Company
Glysantin G05, BASF AG
MOPAR® Part No. 05066386AA, or equivalent325.0
Power Steering
Power Steering, no fluid service required
Power Steering fluid — Mobil ATF-D, Exxon Mobil Corporation, or equivalent 236.3
Rear Axle
Gear Oil 120,000 mi
(192,000 km)Shell Spirax MB 90
MOPAR® Part No. 05136033AA, or equivalent235.0

308 MAINTENANCE SCHEDULESM
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S
8
SCOPE OF WORK FOR MAINTENANCE SERVICE
Oil Service
Oil change
Engine:
Oil change and filter replacement
Check fluid levels of the following system, refill as
necessary.
If fluid is lost, trace and eliminate cause – as a separate
order.
Power-assisted steering
Lubrication work:
Trailer tow hitch (original equipment)
Maintenance
ASSYST maintenance computer resetFunction check
Signalling system,
warning and indicator lamps
Headlamps, exterior lighting
Windscreen wipers,
windscreen washer system
Check for leaks and damage.
Check for abrasion points and ensure that
lines are correctly routed!
All assemblies:
Engine, transmission, transfer case, front axle, rear
axle, steering, power steering pump
All lines and hoses, sensor cables
Rubber boots on front axle drive shafts,
rubber boots on front axle suspension ball joints, shock
absorbers