2006 Alfa Romeo GT disc change

IN AN EMERGENCY
228
Dipped beam headlights
(fig. 25)
To change the bulb, proceed as follows:
– Remove the protective cover releasing
the catches.
– Disconnect the electric connector (A).
– Release the bulb catch (B).
– Remove the bulb and replace it.
– Fit a new bulb, making the tabs of the
metallic part coincide with the grooves on
the reflector, then hook the bulb holder
catch (B).
– Re-connect the electric connector (A).
– Refit the protective cover correctly.
fig. 25
A0A0162b
Main beam headlights
(fig. 27)
To change the bulb, proceed as follows:
– Remove the protective cover releasing
the catches.
– Disconnect the electric connector (A).
– Release the bulb catch (B).
– Remove the bulb and replace it.
– Fit a new bulb, making the tabs of the
metallic part coincide with the grooves on
the reflector, then hook the bulb holder
catch (B).
– Re-connect the electric connector (A).
– Refit the protective cover correctly.
fig. 27
A0A0164b
Front side lights(fig. 26)
To change the bulb, proceed as follows:
– Remove the protective cover releasing
the catches.
– Using the extension (A), integral with
the bulb holder (B), withdraw the bulb
holder itself which is snap-fitted.
– Remove the bulb (C), pushing gently
and turning counter-clockwise.
– Change the bulb and re-insert the bulb
holder making sure that it clicks into
place; also check that the bulb is in the
correct position looking at the lamp from
outside.
– Refit the protective cover correctly.
fig. 26
A0A0342b

IN AN EMERGENCY
232
– disconnect the connector (C-fig. 37),
remove the led unit (D) and replace it with
a new unit;
– Refit the unit on the tailgate reversing
the above mentioned procedure.
fig. 37
A0A0632b
fig. 39
A0A0175b
PUDDLE LIGHTS (fig. 38)
(per versions/market where
provided)
To change the bulb, proceed as follows:
– Open the door and slacken the screw
(A) fastening the transparent covers.
– Remove the unit composed of the two
transparent covers then change the bulb,
releasing it from the side contacts making
sure that the new bulb is correctly
clamped between the contacts.
– Realign the two transparent covers
and tighten the fastening screw (A).
IF AN INTERIOR
LIGHT GOES OUT
FRONT ROOF LIGHT
(fig. 39-40)
To change the bulbs, proceed as follows:
– Remove the light unit (A) levering in
the points shown by the arrow (in corre-
spondence with the retainer catches).
– Open the protective cover (B).
– Replace the bulb concerned releasing
it from the side contacts making sure that
the new bulb is correctly clamped
between the contacts.
fig. 38
A0A0174b

VEHICLE MAINTENANCE
256
Used engine oil and filter
contain harmful sub-
stances for the environ-
ment. Contact Alfa Romeo
Authorised Services to have the
oil and the filter changed, as they
are equipped to dispose of the
waste oil and filters respecting
nature and the law.
SELESPEED TRANSMISSION
OIL
(fig. 7)
The Selespeed transmission oil should be
checked with the vehicle on a level sur-
face and with the engine stopped and
cold.
To check the level, proceed as follows:
– turn the ignition key to MAR;
– disconnect the breather tube and
remove the cap (A) checking that the
level corresponds with the MAXmark on
the dipstick integrated with the cap;
– if the oil is below the MAXmark, top
up to reach the correct level;Do not add oil with spec-
ifications other than that
already in the gearbox.
fig. 7
A0A0197b
Used gearbox oil con-
tains dangerous sub-
stances for the environ-
ment. For changing the oil we
advise contacting Alfa Romeo
Authorised Services who are
equipped for disposing of used oil
respecting nature and the law.
Be very careful working
inside the engine com-
partment if the engine is
hot: danger of burns. Remember
that the fan may cut in if the
engine is very hot: danger of
injury.
Engine oil consumption
Max engine oil consumption is usually
400 grams every 1000 km.
During the initial period of use the
engine settles, therefore engine oil con-
sumption may be considered stabilised
only after the first 5000 ÷ 6000 km.
IMPORTANTEngine oil consumption
depends on the way of driving and the
conditions of use of the vehicle.– after refitting the cap, insert the
breather tube firmly on the housing on the
cap and turn the ignition key to STOP.