2006 Alfa Romeo GT ESP

GETTING TO KNOW YOUR CAR
49
Headlamp washers (fig. 65)
These come into operation when the
windscreen washer is turned on with the
dipped/main beam headlights on.
IMPORTANTOn certain versions
when the headlamp washer is operating,
the climate control system automatically
engages inside air re-circulation, to pre-
vent the smell of liquid detergent from
entering the passenger compartment.CRUISE CONTROL
GENERAL
The speed regulator (CRUISE CON-
TROL), with electronic control, makes it
possible to drive the car at the required
speed without pressing the accelerator
pedal. This reduces driving fatigue during
long journeys because the speed memo-
rised is automatically maintained.
IMPORTANTThe device can only be
engaged at speeds between 30 and 190
km/h.
fig. 65
A0A0704bCruise Control must be ac-
tivated only when the
route and traffic allow a
constant speed for a sufficiently
long distance completely safely.
The device is disengaged automatically
in any of the following cases:
– pressing the brake pedal;
– pressing the clutch pedal;
– if the ASR, MSR or VDC system cuts in;
– with Selespeed transmission if a gear
is changed;
– inadvertently moving the Selespeed
gear control lever to N.
CONTROLS(fig. 66)
Cruise Control is controlled by the
ON/OFFknurled ring (A), by the +/–
ring(B) and by the RESbutton (C).
Ring (A) has two positions:
–OFFin this position the device is
deactivated;
fig. 66
A0A0077b

GETTING TO KNOW YOUR CAR
50
TO MEMORISE THE SPEED
Move the ring (A) to ONand take the
car to the required speed normally. Turn
the ring (B) to (+) for at least three sec-
onds, then release it. The car speed is
memorised and it is therefore possible to
release the accelerator pedal.
The car will continue to travel at the
memorised constant speed until one of
the following conditions takes place:
– pressing the brake pedal;
– pressing the clutch pedal;
– if the ASR, MSR or VDC system cuts
in;
– with Selespeed transmission if a gear
is changed;
– inadvertent movement of the
Selespeed gear control lever to position
N.
IMPORTANTIn the case of need
(when overtaking for instance) accelera-
tion is possible simply pressing the accel-
erator pedal; later, releasing the accelera-
tor pedal, the car will return to the speed
memorised previously.
TO RESET THE
MEMORISED SPEED
If the device has been disengaged for
example pressing the brake or clutch
pedal, the memorised speed can be reset
as follows:
– accelerate gradually until reaching a
speed approaching the one memorised;
– engage the gear selected at the time
of speed memorising (4th, 5th or 6th
speed);
– press the RESbutton (C).
TO INCREASE THE
MEMORISED SPEED
The speed memorised can be increased
in two ways:
1) pressing the accelerator and then
memorising the new speed reached (turn-
ing the ring to (B) for more than three sec-
onds);
or
2) momentaneously turning the ring (B)
to (+): each pulse of the ring will corre-
spond to a slight increase in speed (about
1.5 km/h) while pressing continuously
will correspond to a continuous speed
increase. Releasing the ring (B) the new
speed will be memorised automatically. –ONis the normal operating position
of the device. When the ring (A) is in this
position, the warning light
Üon the
instrument cluster turns on.
Ring (B) serves for memorising and
maintaining the car sped or for increasing
or lowering the speed memorised.
Turn the ring (B) to (+) to memorise
the speed reached or increase the speed
memorised.
Turn the ring (B) to (–) to lower the
speed memorised.
Each time the ring is actuated (B) the
speed increases or lowers by about 1.5
km/h.
Keeping the ring turned the speed
changes continuously. The new speed
reached will be maintained automatically.
TheRESbutton (C) resets the memo-
rised speed.
IMPORTANTTurning the ignition key
toSTOPor the ring (A) to OFF, the
speed memorised is cleared and the sys-
tem is switched off.

GETTING TO KNOW YOUR CAR
53
A. Fuel level gauge with reserve warning
light - B. Engine coolant fluid temperature
gauge with maximum temperature warn-
ing light - C. Speedometer - D. Odometer
display (mileage recorder, trip recorder with
headlamp position display - E. Reconfigu-
rable multifunction display - F. Rev counter
Petrol version
A. Fuel level gauge with reserve warning
light - B. Engine coolant fluid temperature
gauge with maximum temperature warn-
ing light - C. Speedometer - D. Odometer
display (mileage recorder, trip meter with
headlamp position display) - E. Reconfigu-
rable multifunction display - F. Rev counter
INSTRUMENT PANEL
Petrol versions
fig. 68 - 1.8 T. SPARK - 2.0 JTS
fig. 69 - 2.0 JTS Selespeed
A0A0656b
A0A0655b

GETTING TO KNOW YOUR CAR
56
FUEL LEVEL GAUGE WITH
RESERVE INDICATOR
This shows the amount of fuel left in the
fuel tank.
The warning light
K(A-fig. 76) turns
on to indicate that approx. 7 litres of fuel
are left in the tank.
IMPORTANTUnder certain conditions
(heavy slopes, for instance), the reading on
the gauge may differ from the actual
amount of fuel in the tank and changes in
level may be indicated late.
This condition falls within the operation
logics of the electronic control circuit to
avoid highly unstable readings due to
swaying of the fuel when travelling.
IMPORTANTRefuelling shall always be
performed with engine off and ignition key
atSTOP. If the engine is off but the key is
atMAR, a wrong fuel level could tem-
porarily be indicated. This is due to the inter-
nal system control logic and cannot be con-
sidered as a system malfunctioning.
ENGINE COOLANT FLUID
TEMPERATURE GAUGE WITH
MAXIMUM TEMPERATURE
WARNING LIGHT
This shows the temperature of the
engine coolant fluid and begins when the
fluid temperature exceeds approx. 50°C.
Normally the pointer should be towards
the middle of the scale. If the pointer
reaches the higher temperatures of the
scale (red area) the request for vehicle
performance should be decreased.
The turning on of the
u(B-fig. 76)
warning light(on some versions together
with the message shown on the reconfig-
urablemultifunction display) indicates that
the coolant fluid temperature is too high;
in this case, stop the engine and contact
Alfa Romeo Authorised Services.IMPORTANTThe temperature of the
engine coolant may rise towards the max-
imum values (red zone) when the vehicle
is driven at low speeds, especially when
the ambient air temperature is high. In
this case it is advisable to stop the vehicle
and switch off the engine for a few min-
utes, after which the journey can be
resumed, preferably at a higher speed.
fig. 76
A0A0668b

GETTING TO KNOW YOUR CAR
60
RECONFIGURABLE MULTIFUNCTION DISPLAY
The reconfigurable multifunction display
is able to display all the useful and neces-
sary information when driving and a menu
allows the following adjustments and/or
settings:
TIME
DATE
OUTSIDE TEMPERATURE
INFORMATION ABOUT VEHICLE CONDI-
TION
- Trip computer
- Lighting adjustment (rheostat)
- Display of failure messages with corre-
sponding symbol
- Display of warning messages with cor-
responding symbol (e.g.: possible ice
on road)
- Gear selected, for 2.0 JTS Selespeed
versions
- Engine oil level (JTD versions only)Reconfigurable multifunction
display menu
SPEED
- Activation/deactivation of the corre-
sponding indication (ON/OFF)
- Setting the speed limit
TRIP B
- Activation/deactivation of the corre-
sponding function (ON/OFF)
TIME
- Setting the hours
- Setting the minutes
DATE
- Setting the day
- Setting the month
- Setting the year
DST (SUMMER TIME)
- Activation/deactivation of summer
time
MODE 12/24
- Selecting the clock mode on 12 or 24
hours
RADIO
- Activation/deactivation of the follow-
ing items on the display:
frequency or RDS message of the
radio station selected, compact
disc and corresponding track selectedTELEPHONE
- Activation/deactivation of the follow-
ing items on the display:
incoming or outgoing phone call with
name and/or number of the sub-
scriber connected
NAVIGATION
- Activation/deactivation of the displays
and information concerning the route
to be followed
LANGUAGE
- Setting the language of the messages
shown on the display
UNITS
- Selection of the following units of mea-
sure: km, mi, °C, °F, km/l, l/100km,
mpg
BUZZER
- Buzzer volume adjustment
SERVICE
- Display of information concerning cor-
rect vehicle maintenance, strictly con-
nected with the Scheduled
Maintenance Programme
MENU OFF
- Exits the menu.

GETTING TO KNOW YOUR CAR
62
MENU OFF
SPEED
TRIP B
TIME
DATE
DST (SUMMER TIME)
MODE 12/24
RADIO TELEPHONE NAVIGATIONLANGUAGEUNITSBUZZERSERVICE
DESCRIPTION OF THE MENU
The menu comprises a series of functions arranged in a “circular fashion” which can be selected through the âandãbuttons for
access to the different select operations and settings (see examples “LANGUAGE” and “DATE” below); for further details, also refer to
“Access to the menu screen” in the previous chapter.
Day
YearMonth
Q
English
Nederlands
Espãnol
Français
Deutsch
Italiano
Q

GETTING TO KNOW YOUR CAR
63
If the display shows a failure message, see the details given in the
“Warning lights” chapter; if there are two or more failures, the display
shows them in cycle, one after the other. To eliminate the display of the
message and/or of the warning light repeated on the rev counter
by the reconfigurable multifunction display press button
Q.
INITIAL CHECK
Turning the ignition key to MAR, the reconfigurable multifunction display shows the message CHECK ACTIVE: the diagnostic phase of
all the electronic systems on the car has started; this lasts for about 4 seconds (for JTD versions only, the multifunction reconfigurable dis-
play is also able to show the engine oil level, see the “Engine oil level check” paragraph below). If no faults are detected, when the engine
has started, the display shows the OK message.
IMPORTANT If the reconfigurable multifunction display shows a failure message, see the details given in the “Warning lights” chapter.
Standard screen with
mechanical transmission Only JTD versionsStandard screen with
Selespeed transmission
The Programmed Maintenance
Schedule includes vehicle
maintenance every 20,000
km; this is shown automatical-
ly with the ignition key at
MAR, starting from 2,000
km (or miles) from this dead-
line and it is shown again
every 200 km.
If no failures
are presentIs the
engine
started?YES
NO

GETTING TO KNOW YOUR CAR
65
ACCESS TO MENU SCREEN
After the INITIAL CHECK, with the car stationary and with the standard screen, it is possible to access the menu screen: press Q.
To navigate use the
âandãbuttons.
Setting the speed limit is also possible with the car on the move.
If the waiting time (no operation) is above 10 seconds, the standard screen or the screen that was active before pressing the
Qbut-
ton is restored automatically; all the operations confirmed are stored.
Display with mechanical
transmission
Display with
Selespeed transmissionIs the car
moving?
See next page to enter
speed limit.
SPEED
TRIP B
TIME
DATE
DST (SUMMER TIME)
MODE 12/24
RADIO
TELEPHONE
NAVIGATION
LANGUAGE
UNITS
BUZZER
SERVICE
MENU OFF
Q
Q
See
INITIAL CHECKNO
YES