2006 Acura RL Owner's Manual

µµ
µ ÛÝ
There are three settings you can
choose f rom:
SHIFT FROM P
The doors lock whenever you move
the shift lever out of Park.
WITH VEH SPD
The doors lock when the vehicle
speed reaches about 10 mph (about
15 km/h).
OFF
The auto door lock is deactivated all
the time.
While the multi-information display
is in the DOOR/WINDOW screen of
the CUSTOMIZE GROUP, press the
SEL/RESET button. The screen
changes to the above display.Press the SEL/RESET button. The
screen changes as shown above.
Select the desired setting by
pressing the INFO ( / ) button,
then press the SEL/RESET button
to enter your selection.
Multi-Inf ormation Display
A ut o Door L ock
120

ÛÝ
To exit AUTO DOOR LOCK without
changing the current setting, select
EXIT by pressing the INFO ( / )
button, then press the SEL/RESET
button. The screen goes back to
CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY. If this
happens, you need to repeat the auto
door lock setup.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
121

ÛÝ
µ
µ ÛÝ
µ
There are three settings you can
choose f rom:
While the multi-information display
is in the DOOR/WINDOW SETUP
screen of the CUSTOMIZE GROUP,
press the SEL/RESET button. The
screen changes to CUSTOMIZE
MENU. Press the INFO ( / )
button until you see the above
display.
SHIFT TO P The driver’s door or
all the doors, depending on the door
lock mode setting ( see page ),
unlock when you move the shif t
lever to Park.
IGN OFF The driver’s door or all
the doors, depending on the door
lock mode setting ( see page ),
unlock when you turn the ignition
switch to the LOCK (0) position.
Press the SEL RESET button. The
screen changes as shown above.
Select the desired setting by
pressing the INFO ( / ) button,
then press the SEL/RESET button
to enter your selection.
OFF The auto door unlock is
deactivated all the time. This is the
factory default setting. 124 124
Multi-Inf ormation Display
A ut o Door Unlock
122

ÛÝ
To exit AUTO DOOR UNLOCK
without changing the current setting,
select EXIT by pressing the INFO
( / ) button, then press the SEL/
RESET button. The screen goes
back to CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY. If this
happens, you need to repeat the auto
door unlock setup.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
123

ÛÝÛ
Ý
To select whether the driver’s door
unlocks or all the doors unlock when
you unlock the doors with the
remote, f ollow these instructions.
While the multi-information display
is in the DOOR/WINDOW SETUP
screen of the CUSTOMIZE GROUP,
press the SEL/RESET button. The
screen changes to CUSTOMIZE
MENU. Press the INFO ( / )
button until you see above display.Press the SEL/RESET button. The
screen changes as shown above.
Select DRIVER DOOR or ALL
DOORS by pressing the INFO ( /
) button, then press the SEL/
RESET button to enter your
selection.
Multi-Inf ormation Display
Door L ock Mode
124

ÛÝ
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY. To exit DOOR LOCK MODE
without changing the current setting,
select EXIT by pressing the INFO
( / ) button, and then press the
SEL/RESET button. The screen
goes back to CUSTOMIZE MENU.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY. If this
happens, you need to repeat the door
lock mode setup.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
125

ÛÝÛÝ
When you press the LOCK button
on the remote to lock the doors and
the trunk, and then press the button
again within 5 seconds, a beeper
sounds once and the exterior lights
blink once to verif y that the doors
arelockedandthesecuritysystemis
set.
When you press the UNLOCK
button on the remote to unlock the
doors, and then press the button
again within 5 seconds, a beeper
sounds twice and the exterior lights
blink twice to verify that the doors
are unlocked and the security
system is turned of f .
To turn this feature on or off, follow
these instructions.
While the multi-information display
is in the DOOR/WINDOW SETUP
screen of the CUSTOMIZE GROUP,
press the SEL/RESET button. The
screen changes to CUSTOMIZE
MENU. Press the INFO ( / )
button until you see the above
display.Press the SEL/RESET button. The
screen changes as shown above.
Select ON or OFF by pressing the
INFO ( / ) button, then press the
SEL/RESET button to enter your
selection.
Multi-Inf ormation Display
K eyless L ock A cknowledgment
126

ÛÝ
To exit KEYLESS LOCK
ACKNOWLEDGEMENT without
changing the current setting, select
EXIT by pressing the INFO ( / )
button, then press the SEL/RESET
button. The screen goes back to
CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY. If this
happens, you need to repeat the
keyless lock acknowledge setup.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
127