2006 Acura RL light

Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Turn on the headlights to test the
new bulb.
(Driver’s side)
Reinstall the engine compartment
side cover. Push the electrical connector back
onto the bulb. Make sure it is on
all the way.Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Push the bulb in slightly, and turn
it counterclockwise.
Reinstall the battery in the reverse
order of removal, and reinstall the
cover on the battery. Remove the left or right side
engine compartment cover f rom
thesideyouareworkingonby
caref ully pulling the cover out (see
page ).
If you are replacing a driver’s side
bulb, slide the battery toward the
engine to get more clearance (see
page ).
2.
1.
4.
5.
6.
7.
8.
3.
362
391
Lights
Replacing a Front T urn Signal
Bulb
374
SOCKET
BULB

Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
(Driver’s side)Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.
Remove the left or right side
engine compartment cover (see
page ).
(Passenger’s side)
Use a f lat-tipped screwdriver to
remove the holding clip f rom the
windshield washer reservoir. If you are replacing a driver’s side
bulb, slide the battery toward the
engine to get more clearance (see
page ).
Reinstall the battery and the
battery cover.
Reinstall the engine compartment
side cover. 1.
2.
4.
5.
6.
7.
8.
3.
4.
362
391
CONT INUED
Lights
Replacing a Front Position/Side
Marker L ight Bulb
Maint enance
375
BULB
HOLDING CLIP

Use a Phillips-head screwdriver to
remove the two mounting bolts
and remove the holding clip with a
f lat-tipped screwdriver.
Caref ully push up the side under
cover into the bumper.
Your vehicle uses halogen light
bulbs. When replacing a bulb, handle
it by its plastic case, and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
(Driver’s side)
Reinstall the battery and the
battery cover.
Reinstall the windshield washer
reservoir. (Passenger’s side)
Reinstall the engine compartment
side cover.
1.
2.
5.
6.
7.
8.
9.
Lights
Replacing a Front Fog L ight Bulb
376
BOLTS
CLIP
Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.

Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it one-
quarter turn counterclockwise.Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the f og lights to test the
new bulb.
Reinstall the two mounting bolts
on the side under cover and
tighten them securely. Put the
holding clip back on the side
under cover and push on the
center until it locks (the center is
flushwiththehead).
3.
4. 5.
6.
8. 7.
Lights
Maint enance
377
BULB

Determine which of the two bulbs
is burned out: turn signal or back-
up light.
Remove the socket by turning it
one-quarter turn counterclockwise.
Remove the burned out bulb by
pulling it straight out of its socket.
Open the trunk lid, and remove
the lef t or right maintenance lid.
Remove the mounting nut with an
8mmwrench.
Carefully pry in the top or bottom
edge of the trim with a small f lat-
tipped screwdriver, and pull the
trim straight back.
Remove the two mounting bolts
with an 8 mm wrench.
Pull the taillight assembly straight
back out of the body.
2. 1.
3.
4.
5.6.
7.
8.
Lights
Replacing Rear Bulbs
378
MOUNTING NUT
MAINTENANCE LID BOLTS
BULBS
TAIL LIGHT TRIM

Dirt build-up in the loops of the seat
belt anchors can cause the belts to
retract slowly. Wipe the insides of
the loops with a clean cloth
dampened in mild soap and warm
water or isopropyl alcohol.
If your seat belts get dirty, use a sof t
brush with a mixture of mild soap
and warm water to clean them. Do
not use bleach, dye, or cleaning
solvents. Let the belts air-dry bef ore
you use the vehicle.
Install the new bulb in the socket
by pushing it straight in the socket
until it bottoms.
Reinstall the socket into the light
assembly. Turn it clockwise to
lock it in place.
Testthelightstomakesurethe
new bulb is working.
Tighten the mounting nut securely,
and reinstall the maintenance lid. When reinstalling the taillight
assembly, align and pop the snap
f asteners in place. Tighten the two
mounting bolts and reinstall the
trim in place.
9.
10.
11.
12.
13. Cleaning the Seat Belts
Lights, Cleaning the Seat Belts
Maint enance
379
LOOP

If you need to park your vehicle f or
an extended period (more than 1
month), there are several things you
should do to prepare it f or storage.
Proper preparation helps prevent
deterioration and makes it easier to
get your vehicle back on the road. If
possible, store your vehicle indoors.Fill the f uel tank.
Change the engine oil and f ilter. Block the rear wheels.
If the vehicle is to be stored f or a
longer period, it should be
supported on jackstands so the
tires are of f the ground.
Leave one window open slightly (if
the vehicle is being stored
indoors).
Disconnect the battery.
Support the f ront wiper blade
arms with a f olded towel or rag so
they do not touch the windshield.
To minimize sticking, apply a
silicone spray lubricant to all door
and trunk seals. Also, apply a
vehiclebodywaxtothepainted
surfaces that mate with the door
and trunk seals.Cover the vehicle with a
‘‘breathable’’ cover, one made
f rom a porous material such as
cotton. Non-porous materials, such
as plastic sheeting, trap moisture,
which can damage the paint.
If possible, periodically run the
engine until it reaches f ull
operating temperature (the
cooling f ans cycle on and of f
twice). Pref erably, do this once a
month.
Wash and dry the exterior
completely.
Cleantheinterior.Makesurethe
carpeting, floor mats, etc., are
completely dry.
Leave the parking brake off. Put
the transmission in Park.
Vehicle Storage
392

Park the vehicle on f irm, level, and
non-slippery ground. Put the
transmission in Park. Apply the
parking brake.Take the tool case out of the spare
tire.
Turn on the hazard warning lights,
and turn the ignition switch to the
LOCK (0) position. Have all
passengers get out of the vehicle
while you change the tire. Open the trunk, and f old the trunk
floor forward.
Unscrew the wing bolt, and
remove the spacer cone. Then
take the spare tire out of its well.
If you have a f lat tire while driving,
stop in a saf e place to change it.
Drive slowly along the shoulder until
you get to an exit or an area to stop
that is far away from the traffic lanes.
1.
2.3.
4.
5.
Models without Michelin PAX System
Changing a Flat Tire
398
SPARE TIRE
TRUNK FLOOR
TOOL CASE JACK
The vehicle can easily roll off
the jack, seriously injuring
anyone underneath.
Follow the directions for
changing a tire exactly, and
never get under the vehicle
when it is supported only by the
jack.