2006 ACURA CSX remove seats


(#'
 )
Driver’s Seat
20-122 Seats
Front Seat Frame Replacement (cont’d)
A
B
C
D
Fastener Locations
:Clip,3
A
E
Check the operation of the driver’s seat position sensor
after any of these actions (see page 24-29):
 Driver’s seat position sensor replacement
 Cover plate (front side of driver’s seat slide rail) replacement
NOTE:  Put on gloves to protect your hands.
 Apply oil to the pivot portions of the slide lock.
 Apply multipurpose grease to the sliding portions and pivot portions of the seat tracks.
 If the side airbag has deployed, replace the seat frame and related pieces with new ones (see page
24-185).
1. Remove the front seat (see page 20-118).
2. Remove these items:  Front seat-back cover/pad (see page 20-123)
 Front seat cushion cover/pad (see page 20-127)
 Driver’s seat position sensor (see page 24-211)
 Front seat belt buckle (see page 24-6) 3. Remove the clips, then remove the recline inner
covers (A), the outer upper rail cover (B), the inner
upper rail cover (C) and the module holder (D) from
the seat frame (E).
4. Install the new seat frame in the reverse order of removal, and note these items:
 Make sure the driver’s seat position sensor connector is plugged in properly.
 If the clips are damaged or stress-whitened, replace them with new ones.
 Push the clips into place securely.
 Make sure the seat wiring harnesses are routed properly and not pinched.
08/08/21 15:03:56 61SNR030_200_0124
ProCarManuals.com
DYNOMITE -2009-





20-124Seats
Front Seat-back Cover Replacement (cont’d)
Fastener Locations
:Clip,2
A
C
B
A A
D
C
A BA
E BC A
B C
D
A B
A
A A
A
5. Detach the clips and the hooks (A) by pu lling out
the bottom of the back cover (B), then gently pull
down the panel to release the hooks (C) from the
seat frame, and remove the cover.
6. Pull the side airbag harness (A) out through the loop (B), and release the Velcro fastener (C) and the
hooks (D), then pull the seat-back cover (E) back. 7. Detach the harness clip (A), and pull the side airbag
harness (B) and seat-back heater harness (C)
(driver’s seat) out through the harness holes (D) in
the seat-back cover and seat frame. Driver’s seat is
shown; passenger’s seat is similar.
8. Remove the side airbag (see page 24-191).
9. Release the hook strips (A), then loosen the seat- back cover (B). Driver’s seat is shown; passenger’s
seat is similar.
08/08/21 15:03:57 61SNR030_200_0126
ProCarManuals.com
DYNOMITE -2009-








20-126Seats
Front Seat-back Cover Replacement (cont’d)
A
B
A AA
A
A
A
B C
D
13. Remove the seat-back cover/pad (A) from the seatframe (B).
14. Pull back the edge of the seat-back cover all the way around, and release the clips (A), then remove
the seat-back cover. 15. Install the cover in the reverse order of removal,
and note these items:
 Reinitialize the ODS unit (see page 24-26).
 To prevent wrinkles when installing a seat-back cover, make sure the material is stretched evenly
over the pad before securing the clips, the hooks,
and the hook strips.
 Replace any clips (A) you removed with new ones.
 Before installing the side airbag (B), make sure the reinforcing cloth (C) is fixed on the seat-back
frame (D) securely.
 Make sure the side airbag harness, and the seat heater harness (some driver’s seat) or the ODS
unit subharness (passenger’s seat) are routed
properly.
08/08/21 15:03:59 61SNR030_200_0128
ProCarManuals.com
DYNOMITE -2009-




Passenger’s seat Driver’s seat
20-128Seats
Front Seat Cushion Cover Replacement (cont’d)
Fastener Location
: Clip, 1
A B
B
A
B
C
C
E
F
DC
H I
J D A
B
D
E
C
D
C
F
G
H
I
J C
E
H
AB
B
A
5. Gently pull out the center cover (A), then detach the clip, and release the hooks (B). Driver’s seat is
shown; passenger’s seat is similar.
6. If equipped, disconnect the seat heater connector(s) (A) and side airbag connector (B) from under the
seat cushion. 7. Release the hooks (C) from the seat cushion framespring (D). Remove the wire ties (E), and pull the
side airbag harness (F) and seat-back heater
harness (G) (driver’s seat) out through the slits (H)
in the seat cushion cover (I). Turn over the seat
cushion cover, and release the hooks (J).
8. Pull the side airbag harness (A) out through the loop (B).
08/08/21 15:04:00 61SNR030_200_0130
ProCarManuals.com
DYNOMITE -2009-






20-130Seats
Front Seat Cushion Cover Replacement (cont’d)
A
B
A
A
A
A A
12. Release the hooks (A) from under the seat cushion
(B).
13. Pull back the edge of the seat-back cover all the way around, and release the clips (A), then remove
the seat-back cover. 14. Install the cover in the reverse order of removal,
and note these items:
 To prevent wrinkles when installing a seat-back cover, make sure the material is stretched evenly
over the pad before securing the clips, the hooks,
and the hook strips.
 Replace any clips (A) you removed with new ones.
08/08/21 15:04:01 61SNR030_200_0132
ProCarManuals.com
DYNOMITE -2009-



20-132Seats
Rear Seat Removal/Installation (cont’d)
Fastener Location
:Bolt,1
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft) FG
H
A B
C
D
E
B A
B
C
D
A
B
Front
4. Remove the left seat-back (A). –1 Fold the left seat-back down.
–2 Pull the rear center seat belt (B) out through theslit (C) in the seat belt guide (D).
–3 Release the Velcro fastener (E), and pull back the seat-back cover (F), then remove the bolt.
–4 Release the hooks (G) of the pivot bracket (H). 5. Extend the rear center seat belt (A) to remove the
left seat-back (B), then release the pivot shaft (C)
from the center pivot bracket (D).
6. If necessary, remove the bushing (A) from the center pivot bracket (B).
08/08/21 15:04:03 61SNR030_200_0134
ProCarManuals.com
DYNOMITE -2009-

Î

Seat Side Bolster
20-134Seats
Rear Seat Removal/Installation (cont’d)
C
D
E
C C
F
B
A
Fastener Location
:Bolt,1
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
2. While pushing down on the seat cushion (A), pullthe seat hook handles (B) to release the hooks (C).
3. Pull back the seat cushion to release the center seat belt (D) and seat belt buckles (E) from their slits (F),
and remove it.
4. Install the seat cushion in the reverse order of removal, and note these items:
 Before attaching the seat cushion, make sure there are no twists or kinks in the seat belts.
 When installing the seat cushion, slip the seat belt buckles through the slits in the seat cushion. NOTE: Take care not to scratch the body or tear the seat
covers.
1. Remove the seat cushion.
2. Remove the bolt.
08/08/21 15:04:03 61SNR030_200_0136
ProCarManuals.com
DYNOMITE -2009-



(#'

 )
20-13820-138 Seats
Rear Seat Armrest Beverage Holder
Replacement (cont’d)
Rear Seat Armrest Replacement
A
B C
B A
B
A
B
C
2. Release the front hooks (A) from the wire (B), then
remove the beverage holder (C).
3. Install the beverage holder in the reverse order of removal. Make sure the front hooks are installed
securely to the wire, then push down on the
beverage holder and install the rear hooks into the
wire securely. NOTE: Take care not to tear the seams or damage the
seat covers.
1. Remove the clip (A) from the left portion of the armrest pivot (B).
2. Slide the armrest (A) toward the driver’s side of the vehicle, and remove the pivot shaft (B) from the
collar (C) on the right side of the vehicle by pulling
back on the armrest.
08/08/21 15:04:05 61SNR030_200_0140
ProCarManuals.com
DYNOMITE -2009-