2005 TOYOTA AVENSIS 41±

022KO±01
02±60
± PREPARATIONSLIDING ROOF/CONVERTIBLE
AVENSIS REPAIR MANUAL (RM1018E)
SLIDING ROOF/CONVERTIBLE
PREPARATION
Recomended Tools
09041±00020Torx Driver T25SLIDING ROOF
09082±00040TOYOTA Electrical TesterSLIDING ROOF SYSTEM
Equipment
Torque wrench

022G7±01
02±58
± PREPARATIONINSTRUMENT PANEL/METER
AVENSIS REPAIR MANUAL (RM1018E)
INSTRUMENT PANEL/METER
PREPARATION
SST
09950±50013Puller C SetINSTRUMENT PANEL SUB±ASSY
LOWER
(09951±05010)Hanger 150INSTRUMENT PANEL SUB±ASSY
LOWER
(09952±05010)Slide ArmINSTRUMENT PANEL SUB±ASSY
LOWER
(09953±05020)Center Bolt 150INSTRUMENT PANEL SUB±ASSY
LOWER
(09954±05021)Claw No.2INSTRUMENT PANEL SUB±ASSY
LOWER
Recomended Tools
09082±00040TOYOTA Electrical TesterCOMBINATION METER
(09083±00150)Test Lead SetCOMBINATION METER
09041±00030Torx Driver T30INSTRUMENT PANEL SUB±ASSY
LOWER
09042±00010Torx Socket T30INSTRUMENT PANEL SUB±ASSY
LOWER
09070±20010Moulding RemoverINSTRUMENT PANEL SUB±ASSY
LOWER
MULTI±DISPLAY (CRT DISPLAY)
DISPLAY
Equipment
Torque wrench
TapeTo avoid surface damage

02±50
± PREPARATIONHEATER & AIR CONDITIONER
AVENSIS REPAIR MANUAL (RM1018E)
09870±00025A/C Quick Joint Puller No.2AIR CONDITIONING RADIATOR
ASSY
09950±50013Puller C SetAIR CONDITIONING RADIATOR
ASSY
BLOWER ASSY
(09951±05010)Hanger 150AIR CONDITIONING RADIATOR
ASSY
BLOWER ASSY
(09952±05010)Slide ArmAIR CONDITIONING RADIATOR
ASSY
BLOWER ASSY
(09953±05020)Center Bolt 150AIR CONDITIONING RADIATOR
ASSY
BLOWER ASSY
(09954±05021)Claw No.2AIR CONDITIONING RADIATOR
ASSY
BLOWER ASSY
Recomended Tools
09040±00011Hexagon Wrench SetAIR CONDITIONING RADIATOR
ASSY
W/RECEIVER CONDENSER ASSY
(09043±20050)Socket Hexagon Wrench 5AIR CONDITIONING RADIATOR
ASSY
(09043±20100)Socket Hexagon Wrench 10W/RECEIVER CONDENSER ASSY
09041±00030Torx Driver T30AIR CONDITIONING RADIATOR
ASSY
BLOWER ASSY
09042±00010Torx Socket T30AIR CONDITIONING RADIATOR
ASSY
BLOWER ASSY
09070±20010Moulding RemoverAIR CONDITIONING CONTROL
ASSY
AIR CONDITIONING RADIATOR
ASSY
BLOWER ASSY
09216±00021Belt Tension GaugeV (COOLER COMPRESSOR TO
CRANKSHAFT PULLEY) BELT NO.1

A63955
GND CH1
(G2)
CH2
(NE+)GND 05±84
± DIAGNOSTICSSFI SYSTEM (1ZZ±FE/3ZZ±FE)
AVENSIS REPAIR MANUAL (RM1018E)
DTC P0335 CRANKSHAFT POSITION SENSOR ºAº
CIRCUIT MALFUNCTION
DTC P1335 CRANKSHAFT POSITION SENSOR CIRCUIT
MALFUNCTION (DURING ENGINE
RUNNING)
CIRCUIT DESCRIPTION
The crankshaft position sensor (NE signal) consists of a magnet, iron core and pick up coil.
The NE signal plate (crankshaft timing pulley) has 34 teeth and is installed to the crankshaft. The NE signal
sensor generates 34 signals at every engine revolution. The ECM detects the crankshaft angle and the en-
gine revolution based on the NE signals, and the cylinder and the angle of the VVT based on the combination
of the G2 and NE signals.
DTC No.DTC Detecting ConditionTrouble Area
P0335

No crankshaft position sensor signal to the ECM during
cranking

Open in NE± circuit
Open or short in crankshaft position sensor circuit

Crankshaft position sensor

Crank angle sensor plate

ECM
P1335
If conditions from (a) through (c) are met:
(a) NE greater than 1,000 rpm
(b) NE signal is not detected for over 0.05 sec.
(c) Not during cranking
Open or short in crankshaft position sensor circuit

Crankshaft position sensor

Crank angle sensor plate

ECM
Reference: Inspection using the oscilloscope.
HINT:
The correct waveform is as shown on the left.
ItemContents
TerminalCH1: G2 ± NE±
CH2: NE+ ± NE±
Equipment Set5V/DIV, 20ms/DIV
ConditionDuring cranking or idling
05B41±03

3 2 1 45678
9 1 0 111 21 31 41 51 6
DLC33 2 1 45678
9 1 0 111 21 31 41 51 6
DLC3
A04550
± DIAGNOSTICSSFI SYSTEM (1AZ±FSE)
05±297
AVENSIS REPAIR MANUAL (RM1018E)
(c) Check the DLC3.
The vehicle's ECM uses the ISO 9141±2 (Euro±OBD)/
ISO 14230(M±OBD) communication protocol. The termi-
nal arrangement of the DLC3 complies with ISO
15031±03 and matches the ISO 9141±2/ ISO 14230 for-
mat.
SymbolTerminal No.Connection/Voltage or ResistanceCondition
SIL7Bus + Line/Pulse generationDuring transmission
CG4Chassis Ground ± Body Ground/1
or lessAlways
SG5Signal Ground ± Body Ground/1
or lessAlways
BAT16Battery Positive ± Body Ground/9 to 14 VAlways
HINT:
If the display shows ºUNABLE TO CONNECT TO VEHICLEº
when you have connected the cable of the hand±held tester to
the DLC3, turned the ignition switch ON and operated the
hand±held tester, there is a problem on the vehicle side or tool
side.

If communication is normal when the tool is connected to
another vehicle, inspect the DLC3 on the original vehicle.

If communication is still impossible when the tool is con-
nected to another vehicle, the problem is probably in the
tool itself, so consult the Service Department listed in the
tool's instruction manual.
(d) Inspect the battery voltage.
Battery voltage: 11 to 14 V
If voltage is below 11 V, recharge the battery before proceeding.
(e) Check the CHK ENG.
(1) The CHK ENG lamp comes on when the ignition
switch is turned ON and the engine is not running.
HINT:
If the CHK ENG is not illuminated, troubleshoot the combination
meter.
(2) When the engine is started, the CHK ENG should
go off. If the lamp remains on, it means that the diag-
nosis system has detected a malfunction or ab-
normality in the system.
2. DTC CHECK (Normal Mode)
NOTICE:
Hand±held tester only:
When the diagnosis system is switched from the normal
mode to the check (test) mode, it erases all DTCs and freeze
frame data recorded in the normal mode. So before switch-
ing modes, always check the DTCs and freeze frame data,
and note them down.

3 2 1 45678
9 1 0 111 21 31 41 51 6
DLC3
A04550
± DIAGNOSTICSECD SYSTEM (1CD±FTV)
05±529
AVENSIS REPAIR MANUAL (RM1018E)

* 2 trip detection logic
When a logic malfunction is first detected, the pend-
ing fault code is stored in the ECM memory (1st trip).
If the same malfunction is detected again during the
second drive test, this second detection causes the
CHK ENG to illuminate (2nd trip) (However, the igni-
tion switch must be turned OFF between the 1st trip
and 2nd trip).

Freeze frame data:
The freeze frame data records the engine condi-
tions (fuel system, calculator load, engine coolant
temperature, engine speed, vehicle speed, etc.)
when the malfunction is detected. When trouble-
shooting, it is useful for determining whether the ve-
hicle was running or stopped, the engine was
warmed up or not, etc. at the time of the malfunc-
tion.

Priorities for troubleshooting:
If troubleshooting priorities for multiple DTCs are
given in the applicable DTC chart, these should be
followed.
(b) Check the DLC3.
The vehicle's ECM uses the ISO 9141±2(Euro±OBD)
communication protocol. The terminal arrangement of
the DLC3 complies with ISO 15031±03 and matches the
ISO 9141±2 format.
Terminal No.Connection / Voltage or ResidenceCondition
7Bus + Line / Pulse generation+During transmission
4Chassis Ground ± Body Ground / 1
or lessAlways
16Battery Positive ± Body Ground / 9 to 14 VAlways
HINT:
If the display shows ºUNABLE TO CONNECT TO VEHICLEº
when you have connected the cable of the hand±held tester to
the DLC3, turned the ignition switch ON and operated the
hand±held tester, there is a problem on the vehicle side or tool
side.

If communication is normal when the tool is connected to
another vehicle, inspect the DLC3 on the original vehicle.

If communication is still impossible when the tool is con-
nected to another vehicle, the problem is probably in the
tool itself, so consult the Service Deparment listed in the
tool's instruction manual.

D25148
DLC3 12345 768
9 1 0111 21 3 1 514 16
FI2547
± DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U241E(1AZ±FE))05±865
AVENSIS REPAIR MANUAL (RM1018E)
(c) Inspect the DLC3.
(1) The vehicle's ECM uses the ISO 9141±2 (Euro±
OBD)/ISO 14230 (M±OBD) communication proto-
col. The terminal arrangement of DLC3 complies
with ISO 15031±3 and matches the ISO
9141±2/ISO 14230 format.
Terminal No.ConnectionVoltage or ResistanceCondition
7Bus
LinePulse generationDuring communication
4Chassis Ground
Body Ground / 1
or lessAlways
16Battery Positive
Body Ground / 9 ± 14 VAlways
HINT:
If your display shows ºUNABLE TO CONNECT TO VEHICLEº
when you have connected the cable of hand±held tester to
DLC3, turned the ignition switch ON and operated the hand±
held tester, there is a problem on the vehicle side or tool side.

If communication is normal when the tool is connected to
another vehicle, inspect DLC3 on the original vehicle.

If communication is still not possible when the tool is con-
nected to another vehicle, the problem is probably in the
tool itself, so consult the Service Department listed in the
tool's instruction manual.
2. INSPECT DIAGNOSIS (NORMAL MODE)
(a) Check the MIL.
(1) The MIL comes on when the ignition switch is turned
ON and the engine is not running.
HINT:
If the MIL does not come on, troubleshoot the combination me-
ter.
(2) When the engine is started, the MIL should go off.
If the light remains on, the diagnosis system has de-
tected a malfunction or abnormality in the system.
(b) Check the DTC, using the hand±held tester.
NOTICE:
Hand±held tester only:
When the diagnostic system is switched from normal mode
to check (test) mode, it erases all DTCs and freeze frame
data recorded in normal mode. So before switching modes,
always check the DTCs and freeze frame data, and note
them down.

D25148
DLC3 12345 768
9 1 0111 21 3 1 514 16
FI2547
± DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U241E(1AZ±FSE))05±921
AVENSIS REPAIR MANUAL (RM1018E)
(6) *2 trip detection logic:
When a malfunction is first detected, the malfunc-
tion code is temporarily stored in the ECM memory
(1st trip). If the same malfunction is detected again
during the second drive test, this second detection
causes the CHK ENG (MIL) to illumenate (2nd trip)
(However, the ignition switch must be turned OFF
between the 1st trip and the 2nd trip.).
(b) Inspect the DLC3.
(1) The vehicle's ECM uses ISO 9141±2 (Euro±OBD)
communication protocol. The terminal arrangement
of DLC3 complies with ISO 15031±3 and matches
the ISO 9141±2 format.
Terminal No.ConnectionVoltage or ResistanceCondition
7Bus
LinePulse generationDuring communication
4Chassis Ground
Body Ground / 1
or lessAlways
16Battery Positive
Body Ground / 9 to 14 VAlways
HINT:
If your display shows ºUNABLE TO CONNECT TO VEHICLEº
when you have connected the cable of hand±held tester to
DLC3, turned the ignition switch ON and operated the hand±
held tester, there is a problem on the vehicle side or tool side.

If communication is normal when the tool is connected to
another vehicle, inspect DLC3 on the original vehicle.

If communication is still not possible when the tool is con-
nected to another vehicle, the problem is probably in the
tool itself, so consult the Service Department listed in the
tool's instruction manual.
2. INSPECT DIAGNOSIS (NORMAL MODE)
(a) Check the MIL.
(1) The MIL comes on when the ignition switch is turned
ON and the engine is not running.
HINT:
If the MIL does not come on, troubleshoot the combination me-
ter.
(2) When the engine is started, the MIL should go off.
If the light remains on, the diagnosis system has de-
tected a malfunction or abnormality in the system.