2005 TOYOTA AVENSIS Air conditioner

I35381
R±W
R±WR±W HF
J26 J27
IK2 IK2A15 SOL+ RR J/CC3
Compressor
Assembly
38A/C Control Assembly
(*2)
(*2)
R±W
(*1)21
Center J/B
R±W
(*1)1
CB9
CJ
Driver Side J/B
6
DCFrom
HTR
Fuse
*1: LHD
*2: RHD 2
± DIAGNOSTICSAIR CONDITIONING SYSTEM
05±1151
AVENSIS REPAIR MANUAL (RM1018E)
AIR CONDITIONER MAGNETIC VALVE CIRCUIT
CIRCUIT DESCRIPTION
The air conditioner magnetic valve is controlled by A/C amplifier.
WIRING DIAGRAM
05C7P±01

I36135
05±1152
±
DIAGNOSTICS AIR CONDITIONING SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
INSPECTION PROCEDURE
1PERFORM ACTUATOR CHECK
(a)Set the actuator check mode (See page 05±1091).
(b)Press the DEF switch and change to the step operation.
(c)Check the air flow level by hand.
Display CodeBlower level
0ON
1ON
2OFF
3OFF
4OFF
5OFF
6OFF
7OFF
8OFF
9OFF
OKPROCEED TO NEXT CIRCUIT INSPECTION SHOWN ON PROBLEM SYMPTOMS TABLE
NG
2INSPECT AIR CONDITIONER MAGNETIC VALVE
(a)Measure the resistance between terminals 1 and 2. Standard: 10 to 11
at 25
C (77
F)
If the resistance is not as specified, replace the compressor
assy.
NGREPLACE W/PULLEY COMPRESSOR ASSY
OK
3CHECK HARNESS AND CONNECTOR(A/C AMPLIFIER ± BATTERY)
(a)Check for an open or short circuit in harness and connector between terminal \
SOL+ of A/C amplifier and battery + terminal (See page 01±32).
NG REPAIR OR REPLACE HARNESS ORCONNECTOR
OK
REPLACE AIR CONDITIONING AMPLIFIER

E66856
05±1526
± DIAGNOSTICSCOMBINATION METER
AVENSIS REPAIR MANUAL (RM1018E)
INSPECTION PROCEDURE
1 CHECK FRONT SEAT INNER BELT ASSY
(a) Check resistance.
(1) Disconnect the connector from front seat inner belt
assy.
(2) Check resistance between the terminal 3 and 1 of
the front seat inner belt assy.
Standard:
ConditionSpecified Condition
Seat belt is fastenedNo continuity
Seat belt is unfastenedContinuity
NG REPLACE FRONT SEAT INNER BELT ASSY
OK
2 CHECK HARNESS OR CONNECTOR(A/C CONTROL ASSEMBLY±FRONT SEAT
INNER BELT ASSY)
(a) Check continuity between the terminal A13±24 / A16±3 of A/C control assembly and the terminal
F19±3 (6) of front passenger's seat belt warning light.
( ): LHD models
(b) Check continuity between the terminal F19±2 (F19±7)of front passenger's seat belt warning light and
the terminal B10±3 of front seat inner belt assy.
( ): LHD models
Standard: Continuity
NG REPAIR OR REPLACE HARNESS OR
CONNECTOR
OK
3 CHECK THAT MALFUNCTION DISAPPEARS A KNOWN GOOD COMBINATION
METER IS INSTALLED
NG CHECK AND REPLACE AIR CONDITIONER
CONTROL ASSEMBLY
OK
CHECK AND REPLACE COMBINATION METER ASSY

141BF±01
A77281
A77301
±
ENGINE MECHANICAL PARTIAL ENGINE ASSY(1AZ±FE)
14±121
AVENSIS REPAIR MANUAL (RM1018E)
REPLACEMENT
1.DISCHARGE FUEL SYSTEM PRESSURE (See page 11±19)
2.REMOVE FRONT WHEELS
3.REMOVE RADIATOR SUPPORT OPENING COVER
4.REMOVE ENGINE ROOM COVER SIDE
5.REMOVE ENGINE UNDER COVER RH
6.REMOVE ENGINE UNDER COVER LH
7.DRAIN COOLANT (See page 16±19)
8.DRAIN ENGINE OIL
(a)Install a new gasket and the drain plug after draining engine oil.
Torque: 25 N
m (255 kgf
cm,18 ft
lbf)
9.DRAIN MANUAL TRANSAXLE OIL (M/T TRANSAXLE) Torque: 49 N
m (500 kgf
cm,36 ft
lbf)
10.DRAIN AUTOMATIC TRANSAXLE FLUID (A/T TRANSAXLE) (See page 40±2)
11.REMOVE ENGINE COVER SUB±ASSY NO.1
(a)Remove 2 nuts and the cylinder head cover No. 1.
12.DISCONNECT RADIATOR HOSE INLET
13.DISCONNECT RADIATOR HOSE OUTLET 14.SEPARATE RADIATOR RELAY BLOCK
(a)Remove 2 bolts and separate the radiator relay block.
15.SEPARATE COOLER REFRIGERANT SUCTION HOSE NO.1 (RHD(W/ AIR CONDITIONER) STEERING POSITION TYPE)
(a)Remove a bolt and separate the suction hose No. 1.
16.REMOVE RADIATOR ASSY (See page 16±24)
17.REMOVE FAN AND GENERATOR V BELT (See page 14±105)
18.REMOVE GENERATOR ASSY (See page 19±20)
19. REMOVE COMPRESSOR AND MAGNETIC CLUTCH (W/ AIR CONDITIONING)
(a) Remove 4 bolts and separate the compressor and magnetic clutch.
HINT:
Secure the hoses off to the side instead of detaching.

A77308
A77303
A77307
±
ENGINE MECHANICAL PARTIAL ENGINE ASSY(1AZ±FE)
14±123
AVENSIS REPAIR MANUAL (RM1018E)
26.REMOVE OIL RESERVOIR BRACKET NO.1
(a)Remove 2 bolts and the oil reservoir bracket No. 1.
27.SEPARATE COOLER REFRIGERANT SUCTION HOSE
NO.1 (LHD(W/ AIR CONDITION ER) STEER ING
POSITION TYPE)
(a)Remove 2 nuts and separate the suction hose.
28.REMOVE ENGINE SERVICE COVER BRACKET RH (W/O AIR CONDITIONING)
(a)Remove a bolt and the service cover bracket RH. 29.REMOVE COOLER BRACKET (LHD(W/ AIRCONDITIONER) STEERING POSITION TYPE)
(a)Remove the 2 nuts and separate the cooler bracket.
30.REMOVE ENGINE SERVICE COVER BRACKET RH (RHD(W/ AIR CONDITIONER) STEERING POSITION TYPE)
(a)Remove the bolt and the service cover bracket RH.
31.DISCONNECT HEATER INLET WATER HOSE (W/ AIR CONDITIONING)
32.DISCONNECT HEATER OUTLET WATER HOSE (W/ AIR CONDITIONING)
33.REMOVE CHARCOAL CANISTER ASSY
34.DISCONNECT FUEL TUBE SUB±ASSY (See page 11±15)
35. DISCONNECT UNION TO CONNECTOR TUBE HOSE
36.REMOVE FLOOR PANEL BRACE FRONT (See page 15±7)
37.REMOVE EXHAUST PIPE ASSY CENTER (See page 15±7)
38.REMOVE EXHAUST PIPE ASSY FRONT (See page 15±7)
39.REMOVE FRONT AXLE HUB LH NUT (See page 30±6)
SST 09330±00030

±
ENGINE MECHANICAL PARTIAL ENGINE ASSY(1AZ±FE)
14±133
AVENSIS REPAIR MANUAL (RM1018E)
128.INSTALL FRONT AXLE ASSY LH
Torque: 294 N
m (3,000 kgf
cm,217 ft
lbf)
129.INSTALL FRONT AXLE ASSY RH
Torque: 294 N
m (3,000 kgf
cm,217 ft
lbf)
130.INSTALL FRONT SUSPENSION ARM SUB±ASSY LOWER NO.1 LH (M/T TRANSAXLE) Torque: 142 N
m (1,448 kgf
cm,104 ft
lbf)
131.INSTALL FRONT SUSPENSION ARM SUB±ASSY LOWER NO.1 LH (A/T TRANSAXLE)
Torque: 142 N
m (1,448 kgf
cm,104 ft
lbf)
132.INSTALL FRONT SUSPENSION ARM SUB±ASSY LOWER NO.1 RH (M/T TRANSAXLE) Torque: 142 N
m (1,448 kgf
cm,104 ft
lbf)
133.INSTALL FRONT SUSPENSION ARM SUB±ASSY LOWER NO.1 RH (A/T TRANSAXLE) Torque: 142 N
m (1,448 kgf
cm,104 ft
lbf)
134.INSTALL FRONT STABILIZER LINK ASSY LH Torque: 74 N
m (755 kgf
cm,55 ft
lbf)
135.INSTALL FRONT STABILIZER LINK ASSY RH Torque: 74 N
m (755 kgf
cm,55 ft
lbf)
136.INSTALL TIE ROD END SUB±ASSY LH (See page 51±36)
137.INSTALL TIE ROD END SUB±ASSY RH
HINT:
Perform the same procedure as above on the opposite side.
138.INSTALL FRONT AXLE HUB LH NUT (See page 30±6)
139.INSTALL FRONT AXLE HUB RH NUT
HINT:
Perform the same procedure as above on the opposite side.
140.INSTALL EXHAUST PIPE ASSY FRONT (See page 15±7)
141.INSTALL EXHAUST PIPE ASSY CENTER (See page 15±7)
142.INSTALL FLOOR PANEL BRACE FRONT Torque: 30 N
m (306 kgf
cm,22 ft
lbf)
143.INSTALL ENGINE SERVICE COVER BRACKET RH (W/O AIR CONDITIONING)
Torque: 9.0 N
m (92 kgf
cm,80 in.
lbf)
144.INSTALL COOLER BRACKET (LHD(W/ AIR CONDITIONER) STEERING POSITION TYPE) Torque: 9.0 N
m (92 kgf
cm,80 in.
lbf)
145.INSTALL ENGINE SERVICE COVER BRACKET RH (RHD(W/ AIR CONDITIONER) STEERING POSITION TYPE)
Torque: 9.0 N
m (92 kgf
cm,80 in.
lbf)
146.INSTALL COOLER REFRIGE RANT SUCTION HOSE NO.1 (LHD(W/ AIR CONDITION ER)
STEERING POSITION TYPE)
147.INSTALL OIL RESERVOIR BRACKET NO.1
Torque: 8.0 N
m (82 kgf
cm,71 in.
lbf)
148.INSTALL RETURN TUBE SUB±ASSY Torque: 8.0 N
m (82 kgf
cm,71 in.
lbf)
149.INSTALL RADIATOR RESERVE TANK SUB±ASSY Torque: 5.0 N
m (51 kgf
cm,44 in.
lbf)
150.INSTALL BATTERY CARRIER
151.INSTALL AIR CLEANER ASSEMBLY WITH HOSE Torque: 5.0 N
m (51 kgf
cm,44 in.
lbf)
152.INSTALL COMPRESSOR AND MAGNETIC CLUTCH (W/ AIR CONDITIONING)
Torque: 25 N
m (255 kgf
cm,18 in.
lbf)
153.INSTALL GENERATOR ASSY (See page 19±20)
154.INSTALL FAN AND GENERATOR V BELT (See page 14±105)

A77521
Generator ASSY Cooler Refrigerant
Suction Hose No. 1
(RHD (w/ Air Conditioning)
Steering Position Type)
Radiator Hose Inlet
Radiator Hose Outlet
Cooler Refrigerant Suction Hose No. 1
(LHD (w/ Air Conditioning) Steering
Position Type)
Union to Connector
Tube Hose
Charcoal Canister Assy
Battery TrayBatteryRadiator ASSY
Compressor and
Magnetic Clutch
(w/ Air Conditioner)
Battery Clamp
Battery CarrierAir Cleaner Assembly with Hose
Radiator Relay Block
52 (530, 38)
9.8 (100, 7.2)
5.0 (51, 44 in.
lbf)
5.0 (51, 44 in.
lbf)
13 (133, 10)
25 (250, 18)
5.0 (51, 44 in.
lbf)
21 (214, 16)
7.0 (71, 62 in.
lbf)
7.0 (71, 62 in.
lbf)
19 (194, 14)
19 (194, 14)
14±112
± ENGINE MECHANICALPARTIAL ENGINE ASSY (1AZ±FE)
AVENSIS REPAIR MANUAL (RM1018E)

A77313
Cooler Bracket
(LHD (w/ Air Conditioner) Steering Position Type)
Oil Reservoir
Bracket No. 1Heater Outlet Water Hose
Heater Inlet Water Hose
Steering Intermediate
Shaft Assy No. 2
Column Hole Cover Silercer Sheet
Front Stabilizer Link Assy
Front Axle Assy
35 (360, 26)
7.0 (71, 62 in.
lbf)
74 (755, 55 )
216 (2,203,159 )
142 (1,448,105 )
N´m (kgf´cm, ft´lbf)
: Specified torque

Non±reusable part
Front Axle Hub Nut
Tie Rod End Sub±assy
5.0 (51, 44 in.
lbf)
5.0 (51, 44 in.
lbf)

Cotter Pin
49 (500, 36)
Front Suspension Arm
Sub±assy Lower No. 1
14±114
± ENGINE MECHANICALPARTIAL ENGINE ASSY (1AZ±FE)
AVENSIS REPAIR MANUAL (RM1018E)