2005 SUZUKI MARUTI coolant

Downloaded from www.Manualslib.com manuals search engine 283K
FOREWORD
All information in this manual is based
on the latest product information
available at the time of publication.
Due to improvements or other
changes, there may be discrepancies
between information in this manual
and your vehicle. MARUTI SUZUKI
INDIA LIMITED reserves the right to
make production changes at any time,
without notice and without incurring
any obligation to make the same or
similar changes to vehicles previously
built or sold. This vehicle may not
comply with standards or regulations
of other countries. Before attempting
to register this vehicle in any other
country, check all applicable
regulations and make any necessary
modifications.
0-1This manual is an essential part of your
vehicle and should remain with the vehicle
when resold or otherwise transferred to a
new owner or operator. Please read this
manual carefully before operating your new
MARUTI SUZUKI and review the manual
from time to time. It contains important
information on safety, operation and
maintenance. You are invited to avail the
three Free Inspection Services as described
in the manual. Three free inspection
coupons are attached to this manual. Please
show this manual to your
dealer while you take your MARUTI SUZUKI
for any Service.
To prolong the life of your vehicle and
reduce maintenance cost, the periodic
maintenance must be carried out according
to “PERIODIC MAINTENANCE SCHEDULE”
described in “INSPECTION AND
MAINTENANCE” section of this manual. It
is essential for preventing trouble and
accidents to ensure your satisfaction and
safety. Daily inspection and care as per
“DAILY INSPECTION CHECKLIST”
described in the “INSPECTION AND
MAINTENANCE” section of this manual is
essential for prolonging the life of the
vehicle and for safe
driving.
MARUTI SUZUKI INDIA LIMITEDMARUTI SUZUKI INDIA LIMITED believes
in conservation and protection of Earth’s
natural resources. To that end, we
encourage every vehicle owner to recycle,
trade-in or properly dispose of, as
appropriate, used Engine Oil, coolant and
other fluids, batteries and tyres etc.

Downloaded from www.Manualslib.com manuals search engine 4383K
BEFORE DRIVING
4-31
Continuing to drive the vehicle when
the malfunction indicator light is on
can cause permanent damage to the
vehicle’s emission control system, and
can affect fuel economy and
driveability.
CAUTION
Have the system inspected by an authorized
MARUTI SUZUKI dealer.
This light comes on when the ignition switch
is turned to the “ON” position, and goes off
when the engine is started.
If this light comes on while driving, the
power steering system may not work prop-
erly. Have the system inspected by your
MARUTI SUZUKI dealer.NOTE:
If the power steering system does not work
properly, you will feel heavier to steer but
you still will be able to steer.
83K-02-077
Electric Power Steering Light
This light comes on when the ignition switch
is turned to the “ON” position, and goes out
when the engine is started. The light will
come on and remain on if there is
insufficient oil pressure. If the light comes
on when driving, pull off the road as soon
as you can and stop the engine.
Check the oil level and add oil if necessary.
If there is enough oil, the lubrication sys-
tem should be inspected by your MARUTI
SUZUKI dealer before you drive the vehi-
cle again.Oil Pressure Light
83K-02-078
CAUTION
If you operate the engine with this
light on, severe engine damage can
result.
Do not rely on the Oil Pressure
Light to indicate the need to add oil.
Be sure to periodically check the
engine oil level.
Charging LightThis light comes on when the ignition switch
is turned to the “ON” position, and goes off
when the engine is started. The light will
come on and remain on if there is
something wrong with the battery charging
system. If the light comes on when the
engine is running, the charging system
should be inspected immediately by your
MARUTI SUZUKI dealer.High Engine Coolant Temperature
Warning Light (red color)
83K-02-07983K-02-080
When the ignition switch is turned to the
“ON” position, this light comes on briefly so
you can check that the light is working. If
this light blinks while driving, it means the
engine is running hot. Avoid driving condi-

Downloaded from www.Manualslib.com manuals search engine 4483K
BEFORE DRIVING
4-32
CAUTION
Continuing to drive the vehicle when
engine overheating is indicated can
result in severe engine damage.Immobilizer System Light (Petrol)
83K-02-081
tions that may lead to actual overheating.
If the light stays on without blinking, then
the engine is overheating. Follow the
instructions in the “If the Engine Overheats”
of “EMERGENCY SERVICE” section.
83K-02-082
This light comes on when the ignition switch
is turned to the “ON” position, and goes off
when the engine is started. If this light
blinks with the ignition switch turned to
“ON”, there may be something wrong with
the immobilizer system. Contact your
MARUTI SUZUKI dealer to have the sys-
tem inspected.
Service Vehicle Soon (SVS) Light
(Diesel)When the ignition switch is turned to the
“ON” position, this light comes on briefly.
If this light comes on when the engine is
running, there may be something wrong with
the engine electronics system. Ask your
MARUTI SUZUKI dealer to have the system
inspected.
If this light blinks with the ignition switch
turned "ON", there may be something wrong
with the immobilizer system. Ask your
MARUTI SUZUKI dealer to have the system
inspected.
Vehicle will not start in this condition.Glow Plug Indicator Light
(Diesel)
83K-02-083
Open Door Warning Light
(if equipped)
83K-02-084
Turn Signal Indicators
83K-02-085
This light remains on until all doors (includ-
ing or excluding the tailgate, depending on
specification of vehicle) are completely
closed.When you turn on the left or right turn sig-
nals, the corresponding green arrow on the
instrument panel will flash along with the
respective turn signal lights. When you turn
on the hazard warning switch, both arrows If the coolant temperature is cool enough,
this light comes on when the ignition switch
is turned on and goes out when the glow
plug is heated enough for engine starting.

Downloaded from www.Manualslib.com manuals search engine 5783K4) Make sure the bonnet is fully closed and
latched.
5) Check the headlights, turn signal lights,
brake lights and horn for proper opera-
tion.
6) Adjust the seat and adjustable head
restraint (if equipped).
7) Check the brake pedal and the parking
brake lever.
8) Adjust the mirrors.
9) Make sure that you and all passengers
have properly fastened your seat belts.
10)Make sure that all warning lights come
on as the key is turned to the “ON” or
“START” position.
11)Check all gauges.
12)Make sure that the BRAKE SYSTEM
WARNING light turns off when the
parking brake is released.
Once a week, or each time you fill your fuel
tank, perform the following under-hood
checks:
1) Engine oil level
2) Coolant level
3) Brake fluid level
4) Windshield washer fluid level
5) Battery solution level
6) Bonnet latch operation
Pull the Bonnet release handle inside the
vehicle. Make sure that you cannot open
the Bonnet all the way without releasingthe secondary latch. Be sure to close
the Bonnet securely after checking for
proper latch operation. See “All latches,
hinges & locks” of “CHASSIS AND
BODY” in the “Periodic Maintenance
Schedule” in the “INSPECTION AND
MAINTENANCE” section for lubrication
schedule.
w ww w
w WARNING
Make sure the bonnet is fully closed
and latched before driving. If it is not,
it can fly up unexpectedly during
driving, obstructing your view and
resulting in an accident.
Once a month, or each time you fill your
fuel tank, check the tyre pressure using a
tyre pressure gauge. Also check the tyre
pressure of the spare tyre.since its pistons, piston rings and cylinder
walls have not yet become conditioned. New
engines reach the normal level of oil
consumption only after approximately 5000
km (3000 miles) driving.
When judging the amount of oil consump-
tion, note that the oil may become diluted
and make it difficult to accurately judge the
true oil level.
As an example, if a vehicle is used for
repeated short trips, and consumes a nor-
mal amount of oil, the dipstick may not
show any drop in the oil level at all, even
after 1000 km (600 miles) or more of driv-
ing. This is because the oil is gradually
becoming diluted with fuel or moisture,
making it appear that the oil level has not
changed.
You should also be aware that the diluting
ingredients evaporate out when the vehicle
is subsequently driven at high speeds, such
as on an expressway, making it appear that
oil is excessively consumed after high-speed
driving.
OPERATING YOUR VEHICLE
5-2
Engine Oil ConsumptionIt is normal for the engine to consume some
engine oil during normal vehicle operation.
The amount of engine oil consumed
depends on the viscosity of the oil, the
quality of the oil and the conditions the
vehicle is driven under.
More oil is consumed during high-speed
driving and when there is frequent acceler-
ation and deceleration. Under high loads,
your engine also will consume more oil.
A new engine also consumes more oil,
83K-03-003
Ignition SwitchEXAMPLE

Downloaded from www.Manualslib.com manuals search engine 8983KINSPECTION AND MAINTENANCE
Maintenance Schedule ....................................................................................................... 9-1
Drive Belt ............................................................................................................................. 9-6
Engine Oil and Filter......................................................................................................... 9-6
Engine Coolant.................................................................................................................... 9-9
Air Cleaner ......................................................................................................................... 9-11
Spark Plugs....................................................................................................................... 9-11
Gear Oil.............................................................................................................................. 9-13
Clutch Pedal...................................................................................................................... 9-14
Fuel Filter (Diesel engine) .............................................................................................. 9-14
Brakes ................................................................................................................................. 9-15
Steering.............................................................................................................................. 9-16
Tyres ................................................................................................................................... 9-17
Battery................................................................................................................................ 9-19
Fuses ................................................................................................................................... 9-20
Bulb Replacement............................................................................................................. 9-23
Wiper Blades..................................................................................................................... 9-26
Windshield Washer Fluid................................................................................................9-28
Air Conditioning System.................................................................................................9-29
INSPECTION AND MAINTENANCE

Downloaded from www.Manualslib.com manuals search engine 9083K
You should take extreme care when
working on your vehicle to prevent
accidental injury. Here are a few pre-
cautions that you should be especially
careful to observe:
To prevent damage or unintended
activation of the air bag system be
sure the battery is disconnected and
the ignition switch has been in the
“LOCK” position for at least 90
seconds before performing any
electrical service work on your
vehicle. Do not touch air bag sys-
tem components and wires. The
wires are wrapped with yellow tape
or yellow tubing, and the couplers
are yellow for easy identification.
w ww w
w WARNING
83K-07-001
w ww w
w WARNING
w ww w
w WARNING
INSPECTION AND MAINTENANCE
9-1
V VV V
V
Do not leave the engine running in
garages or other confined areas.
When the engine is running, keep
hands, clothing, tools, and other
objects away from the fan and drive
belt. Even though the fan may not
be moving, it can automatically turn
on without warning.
When it is necessary to do service
work with the engine running, make
sure that the parking brake is
applied fully and the transmission is
in Neutral.
Do not touch ignition wires or other
ignition system parts when starting
the engine or when the engine is
running, or you could receive an
electric shock.
Be careful not to touch a hot
engine, exhaust manifold and pipes,
muffler, radiator and water hoses.
Do not allow smoking, sparks, or
flames around petrol or the battery.
Flammable fumes are present.
Do not get under your vehicle if it
is supported only with the portable
jack provided in your vehicle.V VV V
V
V VV V
V
Be careful not to cause accidental
short circuits between the positive
and negative battery terminals.
Keep used oil, coolant, and other
fluids away from children and pets.
Dispose of used fluids properly;
never pour them on the ground, into
sewers, etc.V VV V
V
83K-07-002
Maintenance ScheduleThe following table shows the times when
you should perform regular maintenance on
your vehicle. This table shows in kilometers
and months when you should perform
inspections, adjustments, lubrication and
other services.EXAMPLE

Downloaded from www.Manualslib.com manuals search engine 9283K
FREE INSPECTION PERIODIC MAINTENANCE AT COST
Interval: This interval should be judged by odometer km (x1000) 1 5 10 20 30 40 50 60 70 80
reading or months, whichever comes first.months 1 6 12 24 36 48 60 72 84 96
ENGINE
1-1. Water pump drive belt (Tension, Wear) Petrol-----I---R
1-2.Engine Coolant (Level, Leakage) I I I R I R I R I R
1-3. Engine oil and engine oil filter - - R RRRRRRR
1-4.Cooling system hoses and connections (Leakage and Damage)IIIIIIIIII
1-5.Engine bolts (All cylinder head and manifold fixings) - - T - T - T - T -
1-6.Engine Mounting (All cylinder head and manifold fixings) - - T - T - T - T -
1-7. Valve Cleanrance Petrol----I--I--
1-8.Exhaust System (Noise, Leakage etc.) - I - I-----I
1-9. Positive Crank Case Ventilation System
(Hoses, Connections and Valve)-I-I-----I
1-10.Exhaust Gas Recirculation Valve Diesel----C--C--
IGNITION
2-1.Ignition wiring (Damage, Deterioration) - - - I - I - I - I
2-2. Spark Plug (Clean and adjust the gap) Petrol-----R---R
FUEL
3-1. Air cleaner filter element Paved-road Petrol Clean after every 5,000 KM. Replace after every 40,000KM
Diesel Replace after every 20,000 KM. Cleaning not required
Dusty Condition Petrol Clean after every 2,500 KM. or as rquired. Replace after every 40,000KM
Diesel Replace after every 20,000 KM. Cleaning not required.
More frequent replacement if dust condition is severe.
3-2.
Fuel tank cap, fuel lines and connections (Leakage and Damage)
-I---I---I
3-3. Fuel Filter (Leakage) Petrol-----R---R
3-4. Fuel Filter and Water Draining Diesel I I I R I R I R I R
INSPECTION AND MAINTENANCE
9-3

Downloaded from www.Manualslib.com manuals search engine 9883K
INSPECTION AND MAINTENANCE
9-9(For Diesel Engine Model)
83K-07-015
CAUTION
To tighten the oil filter properly, it is
Important to accurately identify the
position at which the filter gasket first
contacts the mounting surface.
CAUTION
To prevent oil leakage, make sure that
the oil filter is tight, but do not over-
tighten it.
(1) Loosen
(2) Tighten
NOTE:
Replace ring along with the new filter never
use the old ring in the new filter.5) Tighten the filter specified turn from the
point of contact with the mounting sur-
face (or to the specified torque) using an
oil filter wrench.Tightening torque for oil filter
Petrol Engine
3/4 turn or
14 Nm (1.4 kg-m, 10.5 lb-ft)
Diesel Engine
3/4 turn or
25 Nm (2.5 kg-m, 18.1 lb-ft)
Refill with Oil and Check for Leaks1) Pour oil through the filler hole and install
the filler cap.
For the approximate capacity of the oil,
refer to the “CAPACITIES” item in the
“SPECIFICATIONS” section.
2) Start the engine and look carefully for
leaks at the oil filter and drain plug. Run
the engine at various speeds for at least
5 minutes.
3) Stop the engine and wait about 5 min-
utes. Check the oil level again and add
oil if necessary. Check for leaks again.
CAUTION
When replacing the oil filter, it is
recommended that you use a
MARUTI genuine replacement filter.
V VV V
V
CAUTION
V VV V
V Oil leaks from around the oil filter or
drain plug indicate incorrect installa-
tion or gasket damage. If you find
any leaks or are not sure that the
filter has been properly tightened,
have the vehicle inspected by your
MARUTI SUZUKI dealer.Engine Coolant(For Petrol Engine Model)
83K-07-016
EXAMPLE
EXAMPLE
83K-07-017