2005 SUZUKI MARUTI ECU

Downloaded from www.Manualslib.com manuals search engine 1683K
You can lock and unlock the tailgate by
using the key in the driver’s door lock.
To open the tailgate, pull up and hold the
tailgate unlatch handle (1) and lift the tailgate.
w ww w
w WARNING
Always make sure that the tailgate is
closed and latched securely. Com-
pletely closing the tailgate helps pre-
vent occupants from being thrown
from the vehicle in the event of an
accident. Completely closing it also
helps keep away exhaust gases from
entering the car.BEFORE DRIVING
4-4
83K-02-011
2) Push open the tailgate from inside by
pushing up on the emergency lever (2)
using a flat blade screw driver or the
jack handle. The tailgate will be latched
again by closing the tailgate simply.
If the tailgate can not be unlatched by pull-
ing up the tailgate unlatch switch (1), have
the vehicle inspected by your MARUTI
SUZUKI authorized dealer. If you can not unlatch the tailgate by pulling
up the unlatch handle (1) due to a malfunc-
tion, follow the procedures below to unlatch
the tailgate from inside the vehicle.
1) Fold the rear seat forward for easier
access. Refer to “Folding Rear Seats”
section for details on how to fold the
rear seat forward.
w ww w
w WARNING
To avoid injury, do not use your fin-
ger to push the emergency lever.
Make sure there is no one near the
tailgate when pushing open the tail-
gate from inside the vehicle.
Keyless Entry System Trans-
mitter (if equipped)
83K-02-012
(1) “LOCK” button
(2) “UNLOCK” button
There are two ways to lock or unlock all
doors (including the tailgate) simultaneously
by operating the transmitter near the vehicle.
Central door locking system
To lock all doors, push the “LOCK” but-
ton (1) once.
To unlock all other doors, push the
“UNLOCK” button (2) once.
The turn signal lights will flash once when
the doors are locked.
When the doors are unlocked:
The turn signal lights will flash twice.
If the interior light switch is in the middle
position, the interior light will turn on for
about 15 seconds and then fade out. If
you insert the key into the ignition switch
during this time, the light will start to
fade out immediately.

Downloaded from www.Manualslib.com manuals search engine 1883K
BEFORE DRIVING
4-6Keyless Entry Cum Alarm
System (if equipped)System
83K-02-015
The Keyless Entry Cum Alarm System has
two basic modes of operation.
VALET MODE
When the vehicle is to be given for servic-
ing or Valet parking, turn the system into
Valet mode. In Valet mode all the Security
features of system will be OFF. The Sys-
tem will work as a Keyless Entry/Exit in this
mode.
83K-02-016
designed to protect your vehicle from
unauthorized entry. The system can be
operated in three stages. The First is “Arm
Stage” , Second is “ Trigger Stage” & Third
is “Disarm Stage”.
ALARM MODE
Alarm mode system is in three stages: Arm,
Disarm & Trigger stage. The system is
83K-02-017
83K-02-018
ARM STAGE
In Arm Stage, your vehicle is safe from any
unauthorized entry.
1) Press and release the Key Lock button.
2) One Siren chirp and one indicator light
flash will confirm Arm and Lock.
3) Doors will get locked and vehicle will get
armed.
4) Visible theft warning LED on security
switch will flash slowly.NOTE: System will not Arm in following
condition:
1. If any of door is open (except Bonnet).
2. If System is in Valet Mode.
3. If Key is in key cylinder.
TRIGGER STAGE
If anybody tries to tamper with the vehicle,
the alarm triggers and indicators flashes
DISARM STAGE
System should be brought in Disarm Mode
83K-02-019

Downloaded from www.Manualslib.com manuals search engine 1983K
BEFORE DRIVING
4-7
while you are entering/exiting the vehicle.
a) Press and release the Key Unlock but-
ton.
b) Two Siren chrip and two indicator light-
flashes will confirm Disarm and Unlock.
c) Doors will get Unlock and vehicle will get
disarmed.
d) Visible theft warning LED on security
switch will flash fastly.
83K-02-020
Panic Alarm (Car Locator)
Panic Alarm is designed to bring attention
to the vehicle and to locate the vehicle in
congested packed parking area.
a) Press and hold the Key Lock & Unlock-
button simultaneously for 3 seconds.b) Panic alarm will be activated and siren
will sound and indicator lights will flash
for 30 seconds.
c) Press and release the Key Lock &
Unlock button simultaneously within 30
seconds to cancel the Panic alarm.
General FeatureMute Lock/Unlock
To Arm/Disram the vehicle without siren
chirps use this function.
a) Press and release the Key Lock &
Unlock buttons simultaneously.
b) Press and release Key Lock or Unlock
button for desired function.Example: To Lock the system without the
Siren chirp sound, press and release the Key
Lock & Unlock button simultaneously, then
press and release the Key Lock button.Auto Rearm
In case of accidental Unlock/Disarm of
vehicle by Key, vehicle will automatically
Lock & Arm within 30 sec. without any indi-
cation, if no door is opened in this 30 sec.NOTE : If the vehicle is in Valet Mode sys-
tem will only Lock the vehicle.Radio Frequency Lock Out
Key Lock/Unlock/Panic will ceases to func-
tion when Key is present in Key cylinder.Flashing LED Status
The flashing LED always reflects the status
of the system as following.
SYSTEM CONDITION LED STATUS
Disarmed condition LED does not glow
Armed condition Slow Flashes of LEDDiagnostic report Visual-LED Sound
Built in shock 2 Flashes Four Chirps
sensor Triggered
Door / Trunk 3 Flashes Four Chirps
Instrusion
Ignition 5 Flashes Four ChirpsIntrusion Alert
The system gives a report if it has been
tampered in your absence.
Programmable Features
System have some feature which can be
programmed by user according to their
choice.
Drive Lock Mode
Drive lock mode can be programmed by
SPEED or can be turn OFF. In case of
drive lock mode is programmed to SPEED
LOCK, all the vehicle doors will lock when
vehicle attains the speed of 20 Km/hr. If
Drive Lock is programmed to OFF, no door
will lock by speed.

Downloaded from www.Manualslib.com manuals search engine 2083K
BEFORE DRIVING
4-8NOTE: In case of Speed Lock feature, open
& close of Door while driving will cause
cancellation of Speed Lock.Drive Unlock Mode
Drive unlock can be programmed by KEY
or can be turn OFF. When programmed to
KEY, turning IGN ON-OFF, then removing
the key from the key cylinder will unlock all
the doors. In case if drive unlock is pro-
grammed to OFF then no door will unlock
by removing key from key cylinder.
Siren Chirp ON/OFF feature
Siren Chirps are produced whenever Sys-
tem is Arm/Disarm by key. When siren chirp
feature disabled, siren will not chirp after
Arm/Disarm by Key.
Shock Sensor feature
This is a very important feature of security
system, It enables protection of your veh-
cle against any major impact. If anybody
tries to tamper with the vehicle, the alarm
triggers. The triggering of the alarm is in
two stages, first acting as a warning to the
intruder and then at full blast. The sensitivity
of impact sensor can be adjusted as desired
by the user.
Programming Drive Lock Mode
a) Open the Driver Door of your vehicle.
b) With your vehicle key in the key cylinder,
turn IGN ON and then switch it OFF.c) Press and release the Security switch
One time.
d) Press and hold the Security switch.
e) One chirp sound confirms entry into
Drive Lock programming mode.
f) Press the Key Lock button (while holding
the Security switch), a single chirp sound
confirms mode changed to speed lock.
g) Two-Siren chirp sound confirms Drive
lock mode OFF.
h) Release the Security switch.
i) Turn the IGN ON.
Programming Drive Unlock Mode
a) Open the Driver Door of your vehicle.
b) With your vehicle key in the key cylinder,
turn IGN ON and then switch it OFF.
c) Press and release the Security switch
two times.
d) Press and hold the Security switch.
e) Two-chirp sound confirms entry into
Drive unlock programming mode.
f) Press the Key Lock button (while hold-
ing the Security switch), a single chirp
sound confirms the mode changed to
key Unlock.
g) Two-siren chirp sound confirms the
mode changed to Drive Unlock mode
OFF.
h) Release the Security switch.
i) Turn the IGN ON.Programming Siren Chirp ON/OFF
a) Open the Driver Door of your vehicle.
b) With your vehicle key in the key cylinder,
turn IGN ON and then switch it OFF.
c) Press and release the Security switch
Three times.
d) Press and hold the Security switch.
e) Three-chirp sound confirms entry into
Siren Chirp ON/OFF programming mode.
f) Press the Key Lock button (while hold-
ing the Security switch), a single sound
confirms the mode changed to Siren
Chirp ON.
g) Two-Siren chirp sound confirms the
mode changed to Siren Chirp OFF.
h) Release the Security switch.
i) Turn the IGN ON. Procedure To Program Feature
Feature 1 Chirp 2 Chirps Default
1. Drive Lock
Mode Speed OFF Speed
2. Drive Unlock
Mode Key OFF Key
3. Siren chirp
ON/OFF ON OFF ON
4. Shock Sensor
ON/OFF ON OFF ON

Downloaded from www.Manualslib.com manuals search engine 2183K
BEFORE DRIVING
4-9
Programming Shock Sensor ON/OFF
a) Open the Driver Door of your vehicle.
b) With your vehicle key in the key cylin-
der, turn IGN ON and then switch it
OFF.
c) Press and release the Security switch
Four times.
d) Press and hold the Security switch.
e) Four-chirp sound confirms entry into
Shock Sensor ON/OFF programming
mode.
f) Press the Key Lock button (while hold-
ing the Security switch), a single chirp
sound confirms the mode changed to
shock sensor ON.
g) Two-Siren chirp sound confirms the
mode changed to shock sensor OFF.
h) Release the Security switch.
i) Turn the IGN ON.
Shock Sensor Sensitivity
Adjustment via Key
Full Blast Adjustment
Full Blast can be adjustment in 16 levels
as mentioned below.
a) Press Unlock button on Key to Unlock/
Disarm the System.
b) Press Lock button on Key to Lock/Arm
the System.
c) Within 5 sec press Lock & Unlock but-
ton simultaneously for at least 2 sec.Siren will give long chirp to confirm entry
into sensitivity adjustment mode
i) Press Key Lock button to adjust the
sensitivity one step lower. Siren will
give one chirp every time lock button
is pressed till at level 0 where it will
give a long chirp. When adjust to level
0, Full Blast will turn OFF
ii) Press Key unlock button to adjust the
sensitivity one step higher. Siren will
give two chirp every time unlock
button is pressed till at level 16 where
it will give a long chirp.
Pre-warn Adjustment
Pre-warn can be adjusted in 16 levels as
mentioned below:
a) Press Lock button on Key to Lock/Arm
the System
b) Press Unlock button on Key to Unlock/
Disarm the System
c) Within 5 sec press Lock & Unlock but-
ton simultaneously for at least 2 sec.
Siren will give Long chirp to confirm
entry into Sensitivity Adjustment Mode.
i) Press Key Lock button to adjust the
sensitivity one step lower. Siren will
give one chirp every time lock button
is pressed till at level 0 where it will
give a long chirp. When adjusts to
level 0, prewarn will turn OFF.ii) Press Key Unlock button to adjust the
sensitivity one step higher. Siren will
give two Chirp every time Unlock
button is pressed till at level 16 where
it will give a long chirp.
Programming of Valet Mode
This feature can be programmed as follows:
i) Close the driver door.
ii) Turn IGN ON-OFF quickly.
iii) Press and hold Security switch for 3 sec
minimum, LED will turn ON for 1 minute.
Repeat step 1-3 to come out of Valet Mode,
1 Siren chirp sound will indicate Valet Mode
OFF.
Program Customer Pincode
(Personalised Pincode)
The Personalised 4-digit number can be
changed from the factory default to ensure
Personalised Security.
Pin code entry
a) Disarm the system.
b) Open the Driver Door.
c) Turn IGN ON then OFF.
d) Within 5 seconds press and release
Valet switch 5 times. A short chirp fol-
lowed by long chirps confirms entry into
Pin Code programming mode.

Downloaded from www.Manualslib.com manuals search engine 2683K
BEFORE DRIVING
4-14
NOTE:
The defogger will work only when the
engine is running.
The defogger will automatically turn off
after the defogger remains on for 15 min-
utes to prevent discharging of the battery.Front SeatsSeat Adjustment
w ww w
w WARNING
Never attempt to adjust the driver’s
seat or seatback while driving. The
seat or seatback could move unex-
pectedly, causing loss of control.
Make sure that the driver’s seat and
seatback are properly adjusted before
you start driving.
w ww w
w WARNING
Heated Rear Window Switch (if
equipped)
83K-02-028
EXAMPLE
An indicator light will be lit when the defog-
ger is on. The defogger will work only when
the engine is running. To turn off the
defogger, push the switch again.
CAUTION
The heated rear window (if equipped)
use a large amount of electricity. Be
sure to turn off after the window has
become clear. When the rear window is misted, push this
switch (1) to clear the window.
Adjusting Seat PositionThe adjustment lever for each front seat is
located under the front of the seat. To
adjust the seat position, pull up on the
adjustment lever and slide the seat forward
or rearward.
After adjustment, try to move the seat for-
ward and rearward to ensure that it is
securely latched.
83K-02-029
EXAMPLE
1) Move the selector switch to the left or
right to select the mirror you wish to
adjust.
2) Press the outer part of the switch that
corresponds to the direction in which you
wish to move the mirror.
3) Return the selector switch to the center
position to help prevent unintended
adjustment.
w ww w
w WARNING
Be careful when judging the size or
distance of a vehicle or other object
seen in the side convex mirror. Be
aware that objects look smaller and
appear farther away than when seen
in a flat mirror.To avoid excessive seat belt slack,
which reduces the effectiveness of the
seat belts as a safety device, make
sure that the seats are adjusted before
the seat belts are fastened.

Downloaded from www.Manualslib.com manuals search engine 2983K
BEFORE DRIVING
4-17
NOTICE
After folding the rear seatback for-
ward, do not allow any foreign mate-
rial to enter the lock opening. This
may cause damage to the inside of
the lock and prevent the seatback
from being locked securely.
w ww w
w WARNING
If you need to carry cargo in the pas-
senger compartment with the rear seat
back folded forward, be sure to secure
the cargo or it may be thrown about,
causing injury. Never pile cargo higher
than the seatbacks.
To return the seat to the normal position,
follow the procedure below.
When returning the rear seatback to
the normal position, be careful that
your finger is not caught between the
lock and the striker.
When returning the rear seatback to
the normal position, make sure that
there is nothing around the striker.
Any foreign materials prevent the
seatback from being locked securely.
83K-02-037
Raise the seatback until it locks into place.
After returning the seat, try moving the
seatback to make sure they are securely
latched.
Do not put your hand into the rear
seatback lock opening, or your finger
may get caught and be injured.
When returning the rear seatback to
the normal position, do not allow
any foreign material to enter the
lock opening. This may prevent the
seatback from being locked
securely.
NOTICE
EXAMPLE
When you hook the belt webbing
and latch plate into the seat belt
hanger, make sure the latch plate is
on the obverse side of the belt web-
bing as shown in the illustration.
Make sure the belt webbing is not
twisted.
CAUTION
2) Lower the adjustable head restraint fully.
83K-02-036
3) For the split seat (if equipped), pull the
release lever on the top of each split
seat, and fold the seatbacks forward.
For the bench seat, pull the both release
levers on the top of the bench seat
together, and fold the seatback forward.EXAMPLEV VV V
V
CAUTIONw ww w
w WARNING
CAUTION
V VV V
V

Downloaded from www.Manualslib.com manuals search engine 3083K
BEFORE DRIVING
4-18
w ww w
w WARNING
An air bag supplements, or adds to,
the frontal crash protection offered by
seat belts. The driver and all pas-
sengers must be properly restrained
by wearing seat belts at all times,
whether or not an air bag is mounted
at their seating position, to minimize
the risk of severe injury or death in
the event of a crash.
83K-02-039
w ww w
w WARNING
Never allow persons to ride in the
cargo area of a vehicle. In the event
of an accident, there is a much
greater risk of injury for persons
who are not riding in a seat with
their seat belt securely fastened.
Seat belts should always be
adjusted as follows:
– the lap portion of the belt should
be worn low across the pelvis, not
across the waist.
– the shoulder straps should be
worn on the outside shoulder
only, and never under the arm.
– the shoulder straps should be
away from your face and neck,
but not falling off your shoulder.
83K-02-040
NOTICE
When returning the rear seatback to
the normal position, be sure to
handle it carefully by hand to avoid
any damage to the lock itself. Do
not push it by using some material
or by applying excessive force.
As the lock is designed exclusively
for securing the rear seatback, do
not use it for any other purpose.
Incorrect use of it may cause
damage to the inside of the lock
and prevent the seatback from being
locked securely.Seat Belts and Child Restraint
Systems
w ww w
w WARNING
Wear Your Seat Belts at All Times.
83K-02-038
V VV V
V