2005 SUZUKI JIMNY wheel

Downloaded from www.Manualslib.com manuals search engine 3D-28 FRONT SUSPENSION
Steering Knuckle / Wheel Spindle
REMOVAL
1) Hoist vehicle and remove wheel.
2) Remove wheel hub assembly, refer to “Wheel Hub / Bearing /
Oil Seal” in this section.
3) Disconnect spindle vacuum hoses (1) from wheel spindle (for
4WD).
4) Remove disc dust cover (1) and wheel spindle (2).
5) Remove tie rod end (and drag rod end) nut(s) and discon-
nect tie rod end (and drag rod end) (2) from steering knuckle
(1) with special tool.
Special tool
(A) : 09913-65210
6) Remove knuckle seal cover bolts. Then remove knuckle seal
cover (1), knuckle seal and knuckle seal retainer from
knuckle. CAUTION:
Give match mark to each spindle vacuum hoses before
removing hose.

Downloaded from www.Manualslib.com manuals search engine FRONT SUSPENSION 3D-29
7) Remove lower and upper kingpins (1).
8) Remove steering knuckle (1).
9) Remove knuckle seal cover (1), knuckle seal (2) and knuckle
seal retainer (3) from front axle housing (4).
10) Remove spindle oil seal by using special tool.
Special tool
(A) : 09913-50121
11) Remove spindle bushing by using special tools.
Special tool
(A) : 09917-88210
(B) : 09916-58210 NOTE:
Upper and lower kingpins (1), when removed, must be
marked off one from the other.
NOTE:
When steering knuckle (1) is pulled, lower kingpin
bearing sometimes falls off. So remove bearing while
pulling off the knuckle gradually.
Upper and lower kingpin bearings must be also
marked off one from the other.
1. Wheel spindle

Downloaded from www.Manualslib.com manuals search engine FRONT SUSPENSION 3D-31
8) Press-fit spindle bushing (2) to wheel spindle (1) by using
special tool.
Set cut part (4) of spindle bushing (2) as shown in figure
(opposite side of the groove (3) of wheel spindle).
Special tool
(A) : 09922-55131
9) Press-fit spindle oil seal (1) until it becomes flush with wheel
spindle (2) surface by using special tool, and then apply
grease to its lip.
Special tool
(A) : 09944-66020
10) Apply grease to spindle oil seal lip.
“A” : Grease 99000-25010
11) Apply grease to spindle bushing inside surface and flange
(2).
“A” : Grease 99000-25010
12) Install wheel spindle to knuckle, coat their mating surface
with sealant.
“B” : Sealant 99000-31110 or 99000-31090
13) Install wheel spindle (1) and disc dust cover (2) to steering
knuckle. Tighten wheel spindle bolts to specified torque.
Tightening torque
Wheel spindle bolts
(a) : 50 N·m (5.0 kg-m, 36.5 lb-ft)
CAUTION:
As this hole is a part of the passage of the vacuum that
activates the air locking hub, if it is clogged with grease,
the air locking hub cannot be locked or unlocked.
Therefore, be careful not to apply too much grease to
avoid clogging the vacuum passage.

Downloaded from www.Manualslib.com manuals search engine 3D-32 FRONT SUSPENSION
14) Blow air into pipes at the top and the front of wheel spindle
and check that it comes out of the hole as shown in figure
(for 4WD).
15) Connect spindle vacuum hoses to wheel spindle (for 4WD).
16) Connect tie rod and drag rod to steering knuckle, refer to
“Tie rod and Drag Rod” in Section 3B.
17) Install wheel hub assembly, refer to “Wheel Hub / Bearing /
Oil Seal” in this section.
18) Install wheel and tighten wheel nuts to specified torque.
Tightening torque
Wheel nuts
: 95 N·m (9.5 kg-m, 69.0 lb-ft)
19) Lower hoist.
Front Axle Shaft / Oil Seal / Kingpin Bearing
Outer Race
REMOVAL
1) Hoist vehicle.
2) Drain differential gear oil from front axle housing by loosing
drain plug (for 4WD).
3) Remove steering knuckle. For details, refer to “Steering
Knuckle / Wheel Spindle” in this section.
4) Draw out axle shaft (2).CAUTION:
As this hole is a part of the passage of the vacuum that
activates the air locking hub, if it is clogged with grease,
the air locking hub cannot be locked or unlocked.
Therefore, be careful not to apply too much grease to
avoid clogging the vacuum passage.
1. Front axle housing

Downloaded from www.Manualslib.com manuals search engine 3D-34 FRONT SUSPENSION
4) Install axle shaft (2) to front axle housing (1) (for 4WD).
5) Install knuckle to front axle housing. For details, refer to
“Steering Knuckle / Wheel Spindle” in this section.
6) Refill front axle (differential) housing with new specified gear
oil (for 4WD). Refer to “Maintenance Service” in Section 7E
for refill.
7) After servicing, check that no oil leakage exists.
Steering Knuckle Seal
REMOVAL
1) Hoist vehicle.
2) Remove knuckle seal cover bolts and seal cover (1).
3) Cut oil seal in place with scissors or knife, and take it off.
INSTALLATION
1) Cut replacement oil seal at one place with scissors or a
knife.

Downloaded from www.Manualslib.com manuals search engine 3D-38 FRONT SUSPENSION
Front Axle Housing
REMOVAL
1) Hoist vehicle.
2) Remove front wheels.
3) Drain front differential gear oil (for 4WD).
4) Remove caliper carrier bolts (R&L) and suspend caliper.
5) Remove right and left brake disc.
6) Remove wheel speed sensor (if equipped with ABS).
7) Disconnect spindle vacuum hoses from wheel spindle (for
4WD).
8) Remove tie rod (and drag rod) end nuts and disconnect tie
rod (and drag rod) ends (2) from knuckle arm (1) (R&L) with
special tool.
Special tool
(A) : 09913-65210 CAUTION:
During removal, be careful not to damage brake flexible
hose and not to depress brake pedal.
NOTE:
If brake disc can not be removed by hand, use 8mm bolts
(1).
CAUTION:
Give match mark to spindle vacuum hose and wheel
spindle before removal.
1. Vacuum hose to lock
2. Vacuum hose to unlock

Downloaded from www.Manualslib.com manuals search engine 3D-42 FRONT SUSPENSION
9) Install right and left axle shafts to axle housing (for 4WD).
Install knuckle to axle housing (for 2WD).
10) Install kingpins (2) and knuckle seal cover (1) to steering
knuckle (R&L), refer to “Steering Knuckle / Wheel Spindle” in
this section.
11) Install right and left brake disc and caliper assembly.
Tighten carrier bolts to specified torque.
Tightening torque
Brake caliper carrier bolts
(a) : 85 N·m (8.5 kg-m, 61.5 lb-ft)
12) Connect spindle vacuum hoses to wheel spindle (for 4WD),
while aligning the match mark.
13) Install ABS wheel sensor to steering knuckle (if equipped
with ABS).
14) Install tie rod ends and drag rod end to knuckle arm (1)
(R&L). Tighten new nuts to specified torque.
Tightening torque
Tie rod end nuts and drag rod end nut (Knuckle side)
(a) : 43 N·m (4.3 kg-m, 31.5 lb-ft)
15) Install wheels and tighten wheel nuts to specified torque.
Tightening torque
Wheel nuts
: 95 N·m (9.5 kg-m, 69.0 lb-ft)
16) Lower hoist.NOTE:
Place knuckle seal and retainer in axle housing before
installing axle shaft (knuckle), using care for installation
direction of knuckle seal.
NOTE:
To prevent ball stud from being rotated while tightening
tie rod end nut, tighten Nut (M12 x 1.25) to about 20 N·m
(2.0 kg-m, 14.5 Ib-ft) and remove it. Then tighten new nut
to specified torque.

Downloaded from www.Manualslib.com manuals search engine FRONT SUSPENSION 3D-43
17) Tighten lateral rod (1) mounting bolt and nut to specified
torque.
Tightening torque
Lateral rod bolt and nut
(a) : 90 N·m (9.0 kg-m, 65.0 lb-ft)
18) Tighten right and left shock absorber lower mounting nuts
and leading arm mounting nuts to specified torque.
Tightening torque
Shock absorber lower nuts and leading arm nuts
(a) : 90 N·m (9.0 kg-m, 65.0 lb-ft)
19) Refill front axle (differential) housing with new specified gear
oil. Refer to “Maintenance Service” in Section 7E for refill.
20) Confirm front end (wheel) alignment referring to “Preliminary
Checks Prior to Adjusting Front Alignment” in Section 3A. NOTE:
When tightening bolt and nut, be sure that vehicle is off
hoist and in non loaded condition.
NOTE:
When tightening these nuts, be sure that vehicle is off
hoist and in non loaded condition.
1. Shock absorber
2. Leading arm