2005 SUBARU FORESTER wheel size

10-3
Appearance care
– CONTINUED –
Carefully flush the suspension and axle parts, as they
are particularly prone to mud and sand buildup. Do not
use a sharp-edged tool to remove caked mud.
NOTE
Be careful not to damage brake hoses, sensor har-
nesses, and other parts when washing suspen-
sion components. TUsing a warm water washer
y Keep a good distance of 12 in (30 cm) or more be-
tween the washer nozzle and the vehicle. y Do not wash the same area continuously.
y If a stain will not come out easily, wash by hand.
Some warm water washers are of the high tempera-
ture, high pressure type, and they can damage or de-
form the resin parts such as mouldings, or cause wa-
ter to leak into the vehicle. „ Waxing and polishing
Always wash and dry the vehicle before waxing and
polishing.
Use a good quality polish and wax and apply them ac-
cording to the manufacturer’s instructions. Wax or pol-
ish when the painted surface is cool.
Be sure to polish and wax the chrome trim, as well as
the painted surfaces. Loss of wax on a painted surface leads to loss of the original luster and also quickens
the deterioration of the surface. It is recommended
that a coat of wax be applied at least once a month, or
whenever the surface no longer repels water.
If the appearance of the paint has diminished to the
point where the luster or tone cannot be restored,
lightly polish the surface with a fine-grained com-
pound. Never polish just the affected area, but include
the surrounding area as well. Always polish in only
one direction. A No. 2000 grain compound is recom-
mended. Never use a coarse-grained compound.
Coarser grained compounds have a smaller grain-size
number and could damage the paint. After polishing
with a compound, coat with wax to restore the original
luster. Frequent polishing with a compound or an in-
correct polishing technique will result in removing the
paint layer and exposing the undercoat. When in
doubt, it is always best to contact your SUBARU deal-
er or an auto paint specialist.
NOTE
Be careful not to block the windshield washer noz-
zles with wax when waxing the vehicle. „
Cleaning aluminum wheels
y Promptly wipe the aluminum wheels clean of any
kind of grime or agent. If dirt is left on too long, it may

11 - 4 8
Maintenance and service
„
Tire rotation
Tire wear varies from wheel to wheel. To maximize the
life of each tire and ensure that the tires wear uniform-
ly, it is best to rotate the tires every 7,500 miles
(12,500 km). Rotating the tires involves switching the
front and rear tires on the right hand side of the vehicle
and similarly switching the front and rear tires on the
left hand side of the vehicle. (Each tire must be kept on
its original side of the vehicle.)
Replace any damaged or unevenly worn tire at the
time of rotation. After tire rotation, adjust the tire pres-
sures and make sure the wheel nuts are correctly
tightened. After driving approximately 600 miles (1,000 km),
check the wheel nuts again and retighten any nut that
has become loose. „
Tire replacement
The wheels and tires are important and integral parts
of your vehicle’s design; they cannot be changed arbi-
trarily. The tires fitted as standard equipment are opti-
mally matched to the characteristics of the vehicle and
were selected to give the best possible combination of
running performance, ride comfort, and service life. It
is essential for every tire to have a size and construc-
tion matching those shown on the tire placard and to
have a speed symbol and load index matching those
shown on the tire placard.
Using tires of a non-specified size detracts from con-
trollability, ride comfort, braking performance, speed-
ometer accuracy and odometer accuracy. It also cre-
ates incorrect body-to-tire clearances and inappropri-
ately changes the vehicle’s ground clearance.
All four tires must be the same in terms of manufactur-
er, brand (tread pattern), construction, and size. You
are advised to replace the tires with new ones that are
identical to those fitted as standard equipment.
For safe vehicle operation, SUBARU recommends re-
HSB056BA

11 -4 9
Maintenance and service
– CONTINUED –
placing all four tires at the same time.
yAll four tires must be the same in terms of
manufacturer, brand (tread pattern), construc-
tion, degree of wear, speed symbol, load index
and size. Mixing tires of different types, sizes or
degrees of wear can result in damage to vehi-
cle’s power train. Use of different types or sizes
of tires can also dangerously reduce controlla-
bility and braking performance and can lead to
an accident.y Use only radial tires. Do not use radial tires
together with belted bias tires and/or bias-ply
tires. Doing so can dangerously reduce control-
lability, resulting in an accident.
„ Wheel replacement
When replacing wheels due, for example, to damage,
make sure the replacement wheels match the specifi-
cations of the wheels that are fitted as standard equip-
ment. Replacement wheels are available from
SUBARU dealers.
Use only those wheels that are specified for
your vehicle. Wheels not meeting specifica-
tions could interfere with brake caliper opera-
tion and may cause the tires to rub against the
wheel well housing during turns. The resulting
loss of vehicle control could lead to an acci-
dent.

12-5
Specifications
– CONTINUED –
„Tires
„ Wheel alignment
Tire sizeP215/60R16 94H
Wheel size16 × 6 1
/2 JJ
PressureFrontLight load29 psi (200 kPa, 2.0 kgf/cm 2
)
Full load29 psi (200 kPa, 2.0 kgf/cm 2
)
RearLight load28 psi (190 kPa, 1.9 kgf/cm 2
)
Full load36 psi (250 kPa, 2.5 kgf/cm 2
)
Trailer towing41 psi (280 kPa, 2.8 kgf/cm 2
)
Item2.5-liter non-turbo models2.5-liter turbo models
Drive systemAWD
ToeFront0 ± 0.12 in (0 ± 3 mm)
Rear0.08 ± 0.12 in (2 ± 3 mm)
CamberFront–0 °25’ ± 45’
Rear–0 °50’ ± 45’–0 °55’ ± 45’

13-5
Consumer information and Reporting safety defects
– CONTINUED –
„Recommended tire inflation pressure
T Recommended cold tire inflation pressure
Recommended cold tire inflation pressure for your vehicle’s tires is as follows,
Tire sizeP215/60R16 94H
Wheel size16 × 6 1
/2 JJ
PressureFrontLight load29 psi (200 kPa, 2.0 kgf/cm 2
)
Full load29 psi (200 kPa, 2.0 kgf/cm 2
)
RearLight load28 psi (190 kPa, 1.9 kgf/cm 2
)
Full load36 psi (250 kPa, 2.5 kgf/cm 2
)
Trailer towing41 psi (280 kPa, 2.8 kgf/cm 2
)

GAS STATION REFERENCE
Fuel: TNon-turbo models
Use only unleaded gasoline with an octane rating of
87 AKI or higher. T Turbo models
Use premium unleaded gasoline with an octane rat-
ing of 91 AKI or higher. If premium unleaded gaso-
line is not available, regular unleaded gasoline with
octane rating of 87 AKI or higher may be temporarily
used. For optimum engine performance and drive-
ability, it is required that you use premium grade un-
leaded gasoline. „ Fuel octane rating
This octane rating is the average of the Research
Octane and Motor numbers and is commonly re- ferred to as the Anti Knock Index (AKI). Refer to “Fu-
el” section in this manual.
Fuel capacity:
15.9 US gal (60 liters, 13.2 Imp gal) Engine oil:
Use only API classification SL with the words “EN-
ERGY CONSERVING” and the New API certification
mark (starburst mark) displayed on the container (IL-SAC GF-3). Engine oil capacity:
4.2 US qt (4.0 liters, 3.5 Imp qt)
Cold tire pressure:
Tire sizeP215/60R16 94H
Wheel size16 × 6 1
/2 JJ
PressureFrontLight load29 psi (200 kPa, 2.0 kgf/cm 2
)
Full load29 psi (200 kPa, 2.0 kgf/cm 2
)
RearLight load28 psi (190 kPa, 1.9 kgf/cm 2
)
Full load36 psi (250 kPa, 2.5 kgf/cm 2
)
Trailer towing41 psi (280 kPa, 2.8 kgf/cm 2
)