2005 Seat Ibiza 5D fog light bulb

If and when
204Some of the electrical items listed in the table are only fitted on certain
models or are optional extras.
Please note that the above list, while corr ect at the time of printing, is subject
to alterations.Lamp changeGeneral notesBefore changing any lamp first turn off the equipment concerned.
Do not touch the lamp glass. Fingerprints vaporise in the heat, causing a
reduction in the lamp life and conden sation on the mirror surface, thus
reducing efficiency.
A lamp should only be placed by one of the same type. The designation is
inscribed on the bulb, either on the glass part or on the base.
It is highly recommended to keep a box of spare lamps in the vehicle. At the
very least, the lamps that most affect road safety should have spares in the
vehicle.
Rear lights on frame
Brake/position 12V/P21/5W
Indicator 12V/P21W Rear lights on tailgate
small position light 12V/W5W
foglight 12V/P21W
reverse light 12V/P21W
Single reflector headlamps
Full / dipped beam 12V 60/55W (H4)
indicator 12V/PY21W
position 12/W5W
Double reflector headlamps
dipped beam 12V/55W (H7)
full lights 12V/55W (H3)
indicator 12V/PY21W
position 12V/W5W
Xenon headlights
7)
Dipped beam 12V/35W (D1S)
8)
full beam 12V/55W (H7)
indicator 12V/PY21W
position lights 12V/W5W
F1
Multi-terminal voltage supply “30”. Internal fuse box 100
G1 Trailer fuse voltage supply in internal fuse box 50
H1 Vacant
Number
Electrical equipment Amperes7)For these type of headlights, the bulbs must be changed by an Authorised Service
Centre, given that complex elements of the vehicle must be removed and that the au-
tomatic control system must be reset.8)Xenon discharge lamps emit 2.5 times as much light flux and have a useful life five
times greater than halogen lamps, this means that, except in case of an abnormal
fault, there is no need to change the bulbs during the vehicle life.
ibiza_ingles Seite 204 Mittwoch, 5. Oktober 2005 5:17 17

If and when211
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Side indicator lamps– Press the indicator to the left or to the right to remove the lamp.
– Remove the lamp holder from the indicator.
– Remove the broken glass bulb and replace with a new bulb.
– Insert the lamp holder in the indicator guide until it clicks into
place.
– First fit the indicator in the opening in the chassis, fastening the tabs ⇒fig. 152 , and then fit in the lamp as shown by the
arrow ⇒fig. 152
Rear lights on the tailgate: Access to the light unitSide light 1/ Fog light/ reverse light
–Open the tailgate.
Fig. 152 Side indicators
A1A2
Fig. 153 Rear light on
tailgateFig. 154 Rear light on
tailgate
ibiza_ingles Seite 211 Mittwoch, 5. Oktober 2005 5:17 17

If and when
212
– Remove the plastic cover ⇒page 211, fig. 153 and the
plastic caps ⇒page 211, fig. 153 carefully levering using a
screwdriver using the flat part of a screwdriver; avoid damage to
the paintwork.
– Extract the bolts ⇒page 211, fig. 154 and unplug the
connector.
– Remove the light from its housing.Rear lights on the tailgate: Access to the bulb
Side light 1/ Fog light/ reverse light
– Unscrew the bolts ⇒fig. 156 and remove the lampholder.
– Press and rotate the large lampholder to the left. In the case of a small lamp, rotate and extract the lampholder and pull on the
lamp.
– Remove lamp and replace.
– Fit the lampholder and proceed with installation.
– Fit the caps and the plastic cover ⇒ fig. 155.
NoteEnsure that all joints and rubber elements as well as the plastic caps are
correctly fitted during installation.
AA
AB
AC
Fig. 155 Rear light on
tailgate
Fig. 156 Access to the
lamp
AD
AB
AA
AB
ibiza_ingles Seite 212 Mittwoch, 5. Oktober 2005 5:17 17