2005 Seat Alhambra display

Instrument panel62
Windscreen washer fluid level*
This warning lamp will light up if the fluid level in the windscreen
washer container is too low.
Add water for the windscreen washers and headlight washers*
⇒
"Windscreen washer" chapter.K
Open door warning lamp*
This warning lamp will light up if any of the doors is open or not
properly closed.
K
Brake pad wear monitor*
The warning lamp will light up if the frontpads are worn out.
You should proceed immediately to a Technical Service Centre to
have the brake pads checked.
Since this warning lamp indicates the wear of the frontpads only,
it is advisable to have the rear brake pads checked at the same
time.
K
Engine oil pressure/level*
The warning lamp lights up for a few seconds as a functional check
when ignition is switched on.
If the warning lamp is red or yellow or flashes it indicates that the
engine oil pressure or level is too low. This warning lamp will also
light up if there is a defect in the oil level indicator.I If
f lli
ig
gh
ht
ts
s uup
p oor
r ffl
la
as
sh
he
es
s rre
ed
d ((i
in
ns
su
uf
ff
fi
ic
ci
ie
en
nt
t ooi
il
l ppr
re
es
ss
su
ur
re
e)
)
If the warning lamp lights up or flashes red while driving an
acoustic signal will sound three times at engine speeds above
1500 rpm. Stop and switch engine off: check oil level and add oil,
if necessary
⇒"Engine oil" chapter.
If the warning lamp flashes even though the oil level is in order, do
not continue driving. Do not even run the engine at idling speed.
Call in expert assistance.
If while driving the engine speed decreases below idling speed the
oil pressure warning lamp may light up. Increase engine speed by
accelerating or changing down gear.
L Li
ig
gh
ht
ts
s uup
p yye
el
ll
lo
ow
w ((o
oi
il
l lle
ev
ve
el
l*
* tto
oo
o llo
ow
w)
)
The yellow warning lamp indicates that the oil level is too low. Stop
engine and add oil
⇒"Engine oil" chapter.
When opening the bonnet the oil level warning is reset. However, if
you do not refill oil the warning will reappear after about 100 km.
F Fl
la
as
sh
he
es
s yye
el
ll
lo
ow
w ((d
de
ef
fe
ec
ct
ti
iv
ve
e ooi
il
l lle
ev
ve
el
l*
* iin
nd
di
ic
ca
at
to
or
r)
)
If the oil level indicator is defective an acoustic signal will sound
and the warning lamp will flash several times.
At the same time the onboard computer will display a warning for a
short time
⇒"Onboard computer" chapter. Take the vehicle to a
Technical Service Centre as soon as possible to have the engine
checked.
From the moment of the defect to the check-up of the engine the
oil level needs to be checked regularly, preferably when filling the
tank.
K

Instrument panel64
O On
nb
bo
oa
ar
rd
d cco
om
mp
pu
ut
te
er
r wwi
it
th
h mmu
ul
lt
ti
i-
-f
fu
un
nc
ct
ti
io
on
n
i in
nd
di
ic
ca
at
to
or
r*
*
Description
In the fig. 55you see a display of instruments in vehicle fitted with
a navigational or telematic* system. In the fig. 56you see a display
for vehicles with onboard computers.
In these displays you see information of the multi-function
indicator and onboard computer. Instructions and functions for the
multifunction indicator are described in the "Instruments" chapter.
C Ca
au
ut
ti
io
on
n
Depending on the model version or the country, please keep in mind that
some of the messages may not appear in the fitted equipment* of your
vehicle or they may not correspond to the ones described in this
Instructions Manual as date of print.
For this reason, we recommend that for additional information you also
check carefully the "Warning lamps" chapter where you will find the different
symbols and a description of their operation.
While the ignition is switched on and you are driving the onboard
computer continuously checks the functioning of certain systems
and components of the vehicle.
Malfunctioning, repair work or urgent servicing is indicated by
acoustic signals and, depending on the priority, by red and yellow
warning lamps in the instrument panel.
In addition to red and yellow symbolsi in
nf
fo
or
rm
ma
at
ti
io
on
n
will also appear
in the driver’s display.
The informative text in the illustrations of this Instructions Manual
appear in Spanish. Depending on the country, the i in
nf
fo
or
rm
ma
at
ti
io
on
n
and
w wa
ar
rn
ni
in
ng
g ffo
or
r tth
he
e ddr
ri
iv
ve
er
r
will appear in the following languages:
English, French, Italian, Spanish, Portuguese and Czech.
K
6
7
8
1/min
x1000
0 20 4060
3050
7
Km/h
C
AL0-076
F
.
4
AL5Sa
fA---
- O- g-F-
e-i-
.
t5Ly
C
AL0-077
Fig. 55
Fig. 56

Instrument panel65
Safety FirstControls and equipment Tips and Maintenance Technical Data
Function check
V Ve
eh
hi
ic
cl
le
es
s wwi
it
th
h mma
an
nu
ua
al
l gge
ea
ar
r
Malfunctioning will be displayed once the ignition is switched on.
At the same time the corresponding acoustic signal will sound.
V Ve
eh
hi
ic
cl
le
es
s wwi
it
th
h aau
ut
to
om
ma
at
ti
ic
c gge
ea
ar
r
Once the ignition is switched on and the lever is in the positions
"P P
" or "N N
" the warning will appear on the driver’s display:
"STOP CAR, PRESS BRAKES TO SET SPEED".
After choosing the speed ("R R
", "D D
" etc.) this warning will disappear.
In case of one or more malfunctions the warning will disappear
after 15 seconds from switching on the ignition and the symbols of
the corresponding malfunction with the respective informative text
will be displayed.
F Fo
or
r aal
ll
l vve
eh
hi
ic
cl
le
es
s:
:
In case of malfunction an acoustic signal will sound with the
following display:
– – PPr
ri
io
or
ri
it
ty
y 11 –– tth
hr
re
ee
e aac
co
ou
us
st
ti
ic
c ssi
ig
gn
na
al
ls
s
– – PPr
ri
io
or
ri
it
ty
y 22 –– oon
ne
e aac
co
ou
us
st
ti
ic
c ssi
ig
gn
na
al
lWith malfunctions of priority 1 and 2 simultaneously three acoustic
signals will sound.
In case of malfunction the symbol with the corresponding
informative text will be displayed.
N No
ot
te
e
The priority 2 malfunctions will appear once the priority 1 malfunctions are
repaired or eliminated.K
Priority 1 (red symbols)
T Th
he
e ppr
ri
io
or
ri
it
ty
y 11 ssy
ym
mb
bo
ol
ls
s ssi
ig
gn
na
al
l dda
an
ng
ge
er
r.
. FFo
or
r tth
hi
is
s rre
ea
as
so
on
n,
, sst
to
op
p tth
he
e
v ve
eh
hi
ic
cl
le
e aan
nd
d ttu
ur
rn
n oof
ff
f een
ng
gi
in
ne
e.
.
Eliminate defect. The help of a mechanic may be necessary.
If there are several priority 1 malfunctions the symbols will appear
consecutively for about 2 seconds. The symbols will flash until the
defect has been corrected.
The following priority 1 malfunction or warning may appear:
E En
ng
gi
in
ne
e ooi
il
l ppr
re
es
ss
su
ur
re
e
The corresponding warning is:
"STOP PRESS OIL"
STOP ENGINE!
If this symbol begins to flash while driving y yo
ou
u mmu
us
st
t sst
to
op
p tth
he
e
v ve
eh
hi
ic
cl
le
e aan
nd
d ssw
wi
it
tc
ch
h oof
ff
f een
ng
gi
in
ne
e
. Check oil level and, if necessary, add
oil
⇒"Engine oil" chapter.

Instrument panel70
N Na
av
vi
ig
ga
at
ti
io
on
n ssy
ys
st
te
em
m*
*If your vehicle is fitted with a n na
av
vi
ig
ga
at
ti
io
on
n ssy
ys
st
te
em
m
you may go from
one indicator to the next using the windscreen wiper lever (by
pressing for more than 2 seconds):
– Navigation indicator.
– Multi-function indicator.
When the navigation or multi-function system is activated the
onboard computer display will most likely show possible failures.
The instructions for the use of the SEAT navigation system is
included in a s se
ep
pa
ar
ra
at
te
e ssu
up
pp
pl
le
em
me
en
nt
t
.
K
6
7
8
1/min
x1000
0 20 4060
3050
7
Km/h
C
AL0-078
AL0-152Fig. 57
Fig. 58

Climate control132
1Display for blower speed for f fr
ro
on
nt
t sse
ea
at
ts
s
2Display AUTO (automaticmode), ECON (compressor off) or OFF
(entire system off)
3Display for ambient temperature
4Display for defrosting windscreen
5Display for air recirculation for f fr
ro
on
nt
t sse
ea
at
ts
s
6Display for air flow direction f fr
ro
on
nt
t
7Display for selected temperature f fr
ro
on
nt
t
8Blower speed indicator f fr
ro
on
nt
t
9Display for selected temperature r re
ea
ar
r
10Button for Automaticoperation (complete system).
11Button for defrosting windscreen.
12Button for air recirculation f fr
ro
on
nt
t sse
ea
at
ts
s
.
13Button for “Blower faster” f fr
ro
on
nt
t
14Button for “Blower slower” f fr
ro
on
nt
t
and button for air conditioner
“OFF” front
15Button for “Air flow to upper part of body” f fr
ro
on
nt
t
16Button for “Air flow to footwell” f fr
ro
on
nt
t
Controls
AUTO
15c22c22c
14
13
12
11
16
15
18
17
20
19
22
21
23
10
2134
5
6789
AL0-115Fig. 131


Climate control133
Safety FirstControls and equipment Tips and Maintenance Technical Data
17Button for “Warmer” f fr
ro
on
nt
t
18Button for “Colder” f fr
ro
on
nt
t
19Button for “Blower faster” r re
ea
ar
r
20Button for “Blower slower” r re
ea
ar
r
and button for air conditioner
“OFF” r re
ea
ar
r
21Button for “Warmer” r re
ea
ar
r
22Button for “Colder” r re
ea
ar
r
23ECON button (complete system off)
When the appropriate buttons are pressed the displays
1, 2, 7,8and 9change or the displays4, 5and 6appear.
T Th
he
e aau
ut
to
om
ma
at
ti
ic
c rre
eg
gu
ul
la
at
ti
io
on
n oof
f tth
he
e ssy
ys
st
te
em
m cca
an
n bbe
e iin
nf
fl
lu
ue
en
nc
ce
ed
d bby
y tth
he
e
b bu
ut
tt
to
on
ns
s
11-
-16,
, 19a
an
nd
d 20.
.K
Climatronic for the driver’s compartment (front)
T
Th
he
e ffo
ol
ll
lo
ow
wi
in
ng
g sst
ta
an
nd
da
ar
rd
d sse
et
tt
ti
in
ng
g iis
s rre
ec
co
om
mm
me
en
nd
de
ed
d ffo
or
r aal
ll
l tti
im
me
es
s oof
f tth
he
e
y ye
ea
ar
r:
:
T Te
em
mp
pe
er
ra
at
tu
ur
re
e aab
bo
ou
ut
t 222
2°
°C
C ((7
72
2°
°F
F)
) aan
nd
d AAU
UT
TO
O bbu
ut
tt
to
on
n.
.
With this setting a pleasant climate in the vehicle is reached most
quickly.
This setting should therefore only be altered when required for
personal comfort.
Arrangement of vents
⇒page 139.K
Using the system
When ignition has been switched on the system normally works in
the automaticmode. Displays1, 2, 3, 7, 8and 9appear.
The Climatronicmaintains the selected vehicle interior temperature
fully automatically.
To do this, the temperature of the air flow as well as the blower
speed (air volume) and air distribution are altered automatically.
The system also takes account of intense sunlight. This eliminates
the need for a manual re-adjustment.
If the settings deviated from Automaticoperation before the
ignition is switched off the selected functions are permanently
stored. Only the function “air recirculation” is cancelled after about
20 minutes.
K

Climate control134
• The interior temperature can be freely selected with buttons17
and 18and is stored permanently until another temperature is
selected.
The interior temperature can be set between +18°C (64°F) and
+29°C (86°F). In this range it is automatically regulated.
If temperatures below +18°C (64°F) are selected “LO” appears in
the display. With temperatures above +29°C (86°F) “HI” is
displayed.
In these two end positions the system works continuously at
maximum cooling or heating output. The temperature is not
regulated.• If the blower speed is changed up or down a stage, automatic
mode is still retained.
• In certain operating conditions it may be found that the system
temporarily carries out functions which are not quite as expected.
This includes, for example, that for a few seconds after starting
from cold, air is directed mainly into the footwell. This is intentional
so that damp air in the system does not cause the windows to mist
up.
K
Notes on Automatic mode (AUTO)
AUTO
15c22c22c
14
13
12
11
16
15
18
17
20
19
22
21
23
10
2134
5
6789
AL0-115Fig. 132

Climate control135
Safety FirstControls and equipment Tips and Maintenance Technical Data
Partial deviation from Automatic mode
In nearly all cases the Automatic mode offers the best conditions
for the comfort of the vehicle occupants all the year round.
In isolated cases however it can be necessary to move away form
certain functions of the automatic mode by pressing various
buttons. The Climatronicstill works automatically.
The blower speed and thus the air volume at the front can be
increased or reduced with buttons
13and 14. This is shown by a
change in the number of lines in display position 1.
• By pressing button
11
– the ECON operation is switched off
– the air recirculation mode is switched off
– the windscreen and side windows can be defrosted or kept free
of misting (direct vents
4onto side windows)
– the dehumidifying and defrosting effect for the windscreen can
be increased if, for example persons with damp clothing are picked
up shortly after moving off.
• A Ai
ir
r rre
ec
ci
ir
rc
cu
ul
la
at
ti
io
on
n
for the front is selected by pressing button
12.
The symbol5appears in the display.
The air recirculation function prevents strong outside smells
entering the vehicle, for example when driving through a tunnelor
standing in a trafficjam.Air recirculation can also be selected if the vehicle is to be heated
or cooled quickly. In this mode, air is drawn in from the vehicle
interior and heated or cooled.
Smoking should be avoided when air recirculation is selected, as
the smoke drawn in from the vehicle interior deposits on the
evaporator of the Climatronic. This leads to permanent odours
when the Climatronicis in operation. These can only be eliminated
by exchanging the evaporator, which is time-consuming and
expensive.
• With buttons
15and 16the air flow can be to the upper part of
the body or into the footwell.
• The combination of buttons
11and 16can be used to direct the
air flow both to the windscreen and into the footwell.
• The combination of buttons
15and 16can be used to direct the
air flow both to the upper body and into the footwell.
• Button
23( (E
EC
CO
ON
N)
) ssw
wi
it
tc
ch
he
es
s tth
he
e cco
oo
ol
li
in
ng
g ssy
ys
st
te
em
m oof
ff
f
. In this mode,
the heating is automatically regulated (without air dehumidifying
and cooling), with the desired interior temperature being attained
as quickly as possible and maintained.
T Th
he
e aai
ir
r rre
ec
ci
ir
rc
cu
ul
la
at
ti
io
on
n mmo
od
de
e ssh
ho
ou
ul
ld
d nno
ot
t bbe
e uus
se
ed
d ffo
or
r aan
n eex
xt
te
en
nd
de
ed
d ppe
er
ri
io
od
d aas
s nno
o
f fr
re
es
sh
h aai
ir
r iis
s ddr
ra
aw
wn
n iin
n aan
nd
d tth
he
e wwi
in
nd
do
ow
ws
s cco
ou
ul
ld
d mmi
is
st
t uup
p.
.
W
WA
AR
RN
NI
IN
NG
G