2005 NISSAN X-TRAIL Crankshaft position sensor

EM-158
[YD22DDTi]
OIL PAN AND OIL STRAINER

b. Insert the seal cutter (special service tool) between oil pan upper
and oil pan lower.
CAUTION:

Be careful not to damage aluminum mating surface.

Do not insert screwdriver, or oil pan flange will be
deformed.
c. Slide the seal cutter by tapping on the side of the seal cutter with
a hammer.
d. Remove oil pan lower.
4. Remove A/C compressor belt. Refer to EM-140, "
DRIVE BELTS" .
5. Remove A/C compressor and bracket. Refer to ATC-144, "
Removal and Installation of Compressor" .
6. Remove front exhaust tube and its support. Refer to EX-2, "
EXHAUST SYSTEM" .
7. Remove crankshaft position sensor from transaxle.
CAUTION:

Avoid impacts such as a dropping.

Do not disassemble.

Keep it away from metal particles.

Do not place sensor close to magnetic materials.
8. Set a suitable transmission jack under transaxle and hoist
engine with engine slinger. Refer to EM-222, "
ENGINE ASSEM-
BLY" .
9. Remove center member. Refer to EM-222, "
ENGINE ASSEM-
BLY" .
10. Remove rear plate cover and transaxle joint bolts.
11. Remove catalyst and catalyst rear diffuser. Refer to EM-149,
"Removal and Installation" .
12. Remove oil strainer.
13. Remove oil pan upper as follows:
SEM544G
SEM545G
PBIC2277E
JEM553G

EM-160
[YD22DDTi]
OIL PAN AND OIL STRAINER


Tighten bolts in numerical order to the specified torque.

Bolt dimensions vary depending on the installation location.
Refer to the following and use appropriate bolts.

The shank length under the bolt neck above is the length of
the threaded part (pilot portion not included).
2. Install oil strainer.
3. Tighten transaxle joint bolts.
4. Install rear plate cover.
5. Install center member. Refer to EM-222, "
ENGINE ASSEMBLY" .
6. Install crankshaft position sensor.
7. Install oil pan lower as follows:
a. Use a scraper to remove old liquid gasket from mating surfaces.
CAUTION:

Also remove old liquid gasket from mating surface of oil
pan upper.

Remove old liquid gasket from bolt hole and thread.
b. Apply a continuous bead of liquid gasket with the tube presser
(special service tool: WS39930000) as shown in the figure.
Use Genuine Liquid Gasket or equivalent.

Be sure liquid gasket is 3.5 to 4.5 mm (0.138 to 0.177 in)
wide.

Attaching should be done within 5 minutes after coating.M6 x 30 mm (1.18 in) : Bolt No. 15, 16
M8 x 25 mm (0.98 in) : Bolt No. 3, 4, 9, 10
M8 x 60 mm (2.36 in) : Bolt No. 1, 2, 5, 6, 7, 8,
11, 12, 13, 14
SBIA0162E
PBIC2277E
SBIA0163E
SBIA0164E

ENGINE ASSEMBLY
EM-223
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
EM

REMOVAL
Description of work
Remove engine and transaxle assembly from vehicle downward. Separate engine and transaxle.
Preparation
1. Remove hood assembly. Refer to BL-12, "HOOD" .
2. Drain engine coolant from radiator drain plug. Refer to CO-32, "
DRAINING ENGINE COOLANT" .
3. Remove the following parts.

LH and RH engine undercover

LH and RH front wheels

Battery; Refer to SC-4, "BATTERY" .

Drive belts; Refer to EM-140, "DRIVE BELTS" .

Air duct and air cleaner case assembly; Refer to EM-142, "AIR CLEANER AND AIR DUCT" .

Alternator; Refer to SC-17, "Removal and Installation" .

Radiator assembly; Refer to CO-35, "RADIATOR" .

Charge air cooler; Refer to EM-144, "CHARGE AIR COOLER" .
4. Disconnect engine room harness from the engine side and set it aside for easier work.
5. Disconnect all vacuum hoses and air hoses connected to vehicle side at engine side.
Engine room LH
1. Disconnect fuel hose, and plug it to prevent fuel from draining. Refer to EM-146, "INTAKE MANIFOLD" .
2. Disconnect heater hose, and install plug it to prevent engine coolant from draining. Refer to EM-146,
"INTAKE MANIFOLD" .
3. Remove clutch operating cylinder from transaxle, and move it aside. Refer to MT-19, "
TRANSAXLE
ASSEMBLY" and CL-12, "OPERATING CYLINDER" .
4. Disconnect shift cable from transaxle. Refer to MT-16, "
CONTROL LINKAGE" .
Engine room RH
1. Remove engine coolant reservoir tank. Refer to CO-35, "RADIATOR" .
2. Remove A/C compressor with piping connected from engine. Temporarily secure it on body with a rope to
avoid putting load on it. Refer to ATC-144, "
Removal and Installation of Compressor" .
Vehicle underbody
1. Remove exhaust front tube. Refer to EX-2, "EXHAUST SYSTEM" .
2. Disconnect power steering fluid cooler piping at a point between body and engine. Refer to PS-37,
"HYDRAULIC LINE" .
3. Remove front wheel sensor (LH and RH) for ABS from brake caliper. Refer to BRC-46, "
WHEEL SEN-
SORS" (ABS), BRC-116, "WHEEL SENSORS" (ESP/TCS/ABS).
4. Remove brake caliper with piping connected from steering knuckle. Temporarily secure it on body with a
rope to avoid load on it. Refer to BR-27, "
FRONT DISC BRAKE" .
5. Remove drive shaft (LH and RH) from steering knuckle. Refer to FA X - 11 , "
FRONT DRIVE SHAFT" .
6. Preparation for the separation work of transaxle as follows:
a. Remove crankshaft position sensor from transmission. Refer toEM-157, "
OIL PAN AND OIL STRAINER" .
b. Remove transaxle joint bolts which pierce at oil pan (lower) rear side. Refer to EM-157, "
OIL PAN AND
OIL STRAINER" .

ENGINE ASSEMBLY
EM-227
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
EM

REMOVAL
Description of work
Remove engine, transaxle and transfer assembly with front suspension member from vehicle downward. Sep-
arate suspension member, and then separate engine and transaxle.
Preparation
1. Remove hood assembly. Refer to BL-12, "HOOD" .
2. Drain engine coolant from radiator drain plug. Refer to CO-32, "
DRAINING ENGINE COOLANT" .
3. Remove the following parts.

LH and RH engine undercover

LH and RH front wheels

Battery; Refer to SC-4, "BATTERY" .

Drive belts; Refer to EM-141, "Removal and Installation" .

Air duct and air cleaner case assembly; Refer to EM-142, "Removal and Installation" .

Alternator; Refer to SC-17, "Removal and Installation" .

Radiator and cooling fan assembly; Refer to CO-35, "Removal and Installation" and CO-37, "COOL-
ING FAN" .

Charge air cooler; Refer to EM-144, "CHARGE AIR COOLER" .
4. Disconnect engine room harness from the engine side and set it aside for easier work.
5. Disconnect all vacuum hoses and air hoses connected to vehicle side at engine side.
Engine room LH
1. Disconnect fuel hose, and plug it to prevent fuel from draining. Refer to EM-146, "INTAKE MANIFOLD" .
2. Disconnect heater hose, and install plug it to prevent engine coolant from draining. Refer to EM-146,
"INTAKE MANIFOLD" .
3. Remove clutch operating cylinder from transaxle, and move it aside. Refer to MT-19, "
TRANSAXLE
ASSEMBLY" and CL-12, "OPERATING CYLINDER" .
4. Disconnect shift cable from transaxle. Refer to MT-16, "
CONTROL LINKAGE" .
Engine room RH
1. Remove engine coolant reservoir tank. Refer to CO-35, "RADIATOR" .
2. Remove A/C compressor with piping connected from engine. Temporarily secure it on body with a rope to
avoid putting load on it. Refer to ATC-144, "
Removal and Installation of Compressor" .
Vehicle underbody
1. Remove exhaust front tube. Refer to EX-2, "Removal and Installation" .
2. Remove propeller shaft. Refer to PR-4, "
Removal and Installation" .
3. Remove steering shaft from steering gear. Refer to PS-11, "
STEERING COLUMN" .
4. Disconnect power steering fluid cooler piping at a point between body and engine. Refer to PS-37,
"HYDRAULIC LINE" .
5. Remove front wheel sensor (LH and RH) for ABS from brake caliper. Refer to BRC-46, "
WHEEL SEN-
SORS" (ABS), BRC-116, "WHEEL SENSORS" (ESP/TCS/ABS).
6. Remove brake caliper with piping connected from steering knuckle. Temporarily secure it on body with a
rope to avoid load on it. Refer to BR-27, "
FRONT DISC BRAKE" .
7. Remove lower ends of LH and RH strut from steering knuckle. Refer to FSU-5, "
FRONT SUSPENSION
ASSEMBLY" .
8. Preparation for the separation work of transaxle as follows:
a. Remove crankshaft position sensor from transmission. Refer toEM-157, "
OIL PAN AND OIL STRAINER" .
b. Remove transaxle joint bolts which pierce at oil pan lower rear side. Refer to EM-157, "
OIL PAN AND OIL
STRAINER" .

EC-6 Wiring Diagram .....................................................515
Diagnostic Procedure ...........................................517
MI & DATA LINK CONNECTORS ...........................518
Wiring Diagram .....................................................518
EVAPORATIVE EMISSION SYSTEM .....................522
Description ............................................................522
Component Inspection ..........................................525
POSITIVE CRANKCASE VENTILATION ...............527
Description ............................................................527
Component Inspection ..........................................527
AUTOMATIC SPEED CONTROL DEVICE (ASCD) .529
System Description ...............................................529
Component Description ........................................530
SERVICE DATA AND SPECIFICATIONS (SDS) ....531
Fuel Pressure .......................................................531
Idle Speed and Ignition Timing .............................531
Calculated Load Value ..........................................531
Mass Air Flow Sensor ...........................................531
Intake Air Temperature Sensor .............................531
Engine Coolant Temperature Sensor ...................531
Heated Oxygen Sensor 1 Heater .........................531
Heated Oxygen sensor 2 Heater ..........................532
Crankshaft Position Sensor (POS) .......................532
Camshaft Position Sensor (PHASE) ....................532
Throttle Control Motor ...........................................532
Injector ..................................................................532
Fuel Pump ............................................................532
QR (WITHOUT EURO-OBD)
INDEX FOR DTC .....................................................533
Alphabetical Index ................................................533
DTC No. Index ......................................................535
PRECAUTIONS .......................................................537
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ...............................................................537
On Board Diagnostic (OBD) System of Engine ....537
Precaution ............................................................537
Wiring Diagrams and Trouble Diagnosis ..............540
PREPARATION .......................................................541
Special Service Tools ...........................................541
Commercial Service Tools ....................................542
ENGINE CONTROL SYSTEM ................................543
System Diagram ...................................................543
Vacuum Hose Drawing .........................................545
System Chart ........................................................547
Multiport Fuel Injection (MFI) System ...................548
Electronic Ignition (EI) System .............................550
Air Conditioning Cut Control .................................551
Fuel Cut Control (at No Load and High Engine
Speed) ..................................................................551
CAN Communication Unit .....................................552
BASIC SERVICE PROCEDURE .............................558
Idle Speed and Ignition Timing Check ..................558
Accelerator Pedal Released Position Learning ....559
Throttle Valve Closed Position Learning ...............560
Idle Air Volume Learning ......................................560
Fuel Pressure Check ............................................562ON BOARD DIAGNOSTIC (OBD) SYSTEM ...........565
Introduction ...........................................................565
Two Trip Detection Logic .......................................565
Emission-related Diagnostic Information ..............565
NATS (Nissan Anti-theft System) ..........................567
Malfunction Indicator (MI) .....................................568
TROUBLE DIAGNOSIS ..........................................572
Trouble Diagnosis Introduction .............................572
DTC Inspection Priority Chart ...............................576
Fail-Safe Chart ......................................................577
Basic Inspection ....................................................578
Symptom Matrix Chart ..........................................584
Engine Control Component Parts Location ...........588
Circuit Diagram .....................................................593
ECM Harness Connector Terminal Layout ............595
ECM Terminals and Reference Value ...................595
CONSULT-II Function (ENGINE) ..........................604
CONSULT-II Reference Value in Data Monitor Mode
.615
Major Sensor Reference Graph in Data Monitor
Mode .....................................................................618
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .620
Description ............................................................620
Testing Condition ..................................................620
Inspection Procedure ............................................620
Diagnostic Procedure ............................................621
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT .......................................................................624
Description ............................................................624
Diagnostic Procedure ............................................624
POWER SUPPLY AND GROUND CIRCUIT ...........625
Wiring Diagram .....................................................625
Diagnostic Procedure ............................................626
Component Inspection ..........................................632
Ground Inspection .................................................632
DTC U1000, U1001 CAN COMMUNICATION LINE .633
Description ............................................................633
On Board Diagnosis Logic ....................................633
DTC Confirmation Procedure ................................633
Wiring Diagram .....................................................634
Diagnostic Procedure ............................................635
DTC P0011 IVT CONTROL .....................................636
Description ............................................................636
CONSULT-II Reference Value in Data Monitor Mode
.637
On Board Diagnosis Logic ....................................637
DTC Confirmation Procedure ................................637
Overall Function Check .........................................639
Wiring Diagram .....................................................640
Diagnostic Procedure ............................................641
Component Inspection ..........................................643
Removal and Installation .......................................643
DTC P0102, P0103 MAF SENSOR .........................644
Component Description ........................................644
CONSULT-II Reference Value in Data Monitor Mode
.644
On Board Diagnosis Logic ....................................644
DTC Confirmation Procedure ................................644
Wiring Diagram .....................................................646

EC-10 CONSULT-II Reference Value in Data Monitor Mode
.946
Wiring Diagram .....................................................947
Diagnostic Procedure ...........................................948
Component Inspection ..........................................953
ASCD INDICATOR ..................................................954
Component Description ........................................954
CONSULT-II Reference Value in Data Monitor Mode
.954
Wiring Diagram .....................................................955
Diagnostic Procedure ...........................................957
MI & DATA LINK CONNECTORS ...........................958
Wiring Diagram .....................................................958
EVAPORATIVE EMISSION SYSTEM .....................962
Description ............................................................962
Component Inspection ..........................................965
POSITIVE CRANKCASE VENTILATION ...............967
Description ............................................................967
Component Inspection ..........................................967
AUTOMATIC SPEED CONTROL DEVICE (ASCD) .969
System Description ...............................................969
Component Description ........................................970
SERVICE DATA AND SPECIFICATIONS (SDS) ....971
Fuel Pressure .......................................................971
Idle Speed and Ignition Timing .............................971
Mass Air Flow Sensor ...........................................971
Intake Air Temperature Sensor .............................971
Engine Coolant Temperature Sensor ...................971
Heated Oxygen Sensor 1 Heater .........................971
Heated Oxygen sensor 2 Heater ..........................971
Crankshaft Position Sensor (POS) .......................971
Camshaft Position Sensor (PHASE) ....................972
Throttle Control Motor ...........................................972
Injector ..................................................................972
Fuel Pump ............................................................972
YD (WITH EURO-OBD)
INDEX FOR DTC .....................................................973
Alphabetical Index ................................................973
DTC No. Index ......................................................976
PRECAUTIONS .......................................................979
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ...............................................................979
On Board Diagnostic (OBD) System of Engine ....979
Precautions ...........................................................979
Wiring Diagrams and Trouble Diagnosis ..............982
PREPARATION .......................................................983
Special Service Tools ...........................................983
Commercial Service Tools ....................................983
ENGINE CONTROL SYSTEM ................................984
System Diagram ...................................................984
Vacuum Hose Drawing .........................................985
System Chart ........................................................986
Fuel Injection Control System ...............................986
Fuel Injection Timing Control System ...................988
Air Conditioning Cut Control .................................988
Fuel Cut Control (At No Load & High Engine Speed) .988Crankcase Ventilation System ..............................989
CAN Communication ............................................989
BASIC SERVICE PROCEDURE .............................994
Fuel Filter ..............................................................994
Fuel Pump Learning Value Clearing .....................994
ON BOARD DIAGNOSTIC (OBD) SYSTEM ...........996
Introduction ...........................................................996
Three Trip Detection Logic and One Trip Detection
Logic .....................................................................996
Emission-related Diagnostic Information ..............996
NATS (Nissan Anti-theft System) .........................1001
Malfunction Indicator (MI) ....................................1001
OBD System Operation Chart ..............................1004
TROUBLE DIAGNOSIS .........................................1007
Trouble Diagnosis Introduction ............................1007
DTC Inspection Priority Chart ..............................1010
Basic Inspection ...................................................1012
Symptom Matrix Chart .........................................1016
Engine Control Component Parts Location ..........1020
Circuit Diagram ....................................................1025
ECM Harness Connector Terminal Layout ...........1027
ECM Terminals And Reference Value ..................1027
CONSULT-II Function (ENGINE) .........................1034
Generic Scan Tool (GST) Function ......................1040
CONSULT-II Reference Value in Data Monitor Mode
1042
Major Sensor Reference Graph in Data Monitor
Mode ....................................................................1043
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT ......................................................................1045
Description ...........................................................1045
Diagnostic Procedure ...........................................1045
POWER SUPPLY AND GROUND CIRCUIT ..........1046
Wiring Diagram ....................................................1046
Diagnostic Procedure ...........................................1047
Component Inspection .........................................1054
Ground Inspection ................................................1055
DTC U1000 CAN COMMUNICATION LINE ...........1056
Description ...........................................................1056
On Board Diagnosis Logic ...................................1056
DTC Confirmation Procedure ...............................1056
Wiring Diagram ....................................................1057
Diagnostic Procedure ...........................................1058
DTC P0016 CKP - CMP CORRELATION ..............1059
On Board Diagnosis Logic ...................................1059
DTC Confirmation Procedure ...............................1059
Diagnostic Procedure ...........................................1059
DTC P0045 TC BOOST CONTROL SOLENOID
VALVE .....................................................................1061
Description ...........................................................1061
On Board Diagnosis Logic ...................................1061
DTC Confirmation Procedure ...............................1061
Wiring Diagram ....................................................1062
Diagnostic Procedure ...........................................1063
Component Inspection .........................................1064
DTC P0088 FUEL SYSTEM ...................................1066
On Board Diagnosis Logic ...................................1066
DTC Confirmation Procedure ...............................1066

EC-14 Wiring Diagram ....................................................1294
Diagnostic Procedure ..........................................1296
DTC P2147, P2148 FUEL INJECTOR CIRCUIT ...1297
Component Description .......................................1297
CONSULT-II Reference Value in Data Monitor Mode
1297
On Board Diagnosis Logic ...................................1297
DTC Confirmation Procedure ..............................1297
Wiring Diagram ....................................................1298
Diagnostic Procedure ..........................................1300
Component Inspection .........................................1301
Removal and Installation .....................................1302
DTC P2228, P2229 BARO SENSOR .....................1303
Description ...........................................................1303
On Board Diagnosis Logic ...................................1303
DTC Confirmation Procedure ..............................1303
Diagnostic Procedure ..........................................1304
GLOW CONTROL SYSTEM ..................................1305
Description ...........................................................1305
Wiring Diagram ....................................................1306
Diagnostic Procedure ..........................................1308
Component Inspection .........................................1312
Removal and Installation .....................................1312
BRAKE SWITCH ....................................................1313
Description ...........................................................1313
CONSULT-II Reference Value in Data Monitor Mode
1313
Wiring Diagram ....................................................1314
Diagnostic Procedure ..........................................1316
Component Inspection .........................................1320
PNP SWITCH .........................................................1322
Description ...........................................................1322
CONSULT-II Reference Value in Data Monitor Mode
1322
Wiring Diagram ....................................................1323
Diagnostic Procedure ..........................................1324
PSP SWITCH .........................................................1326
Component Description .......................................1326
CONSULT-II Reference Value in Data Monitor Mode
1326
Wiring Diagram ....................................................1327
Diagnostic Procedure ..........................................1328
Component Inspection .........................................1329
Removal and Installation .....................................1330
FUEL TRANSPORT PUMP ....................................1331
Description ...........................................................1331
Wiring Diagram ....................................................1332
Diagnostic Procedure ..........................................1334
Component Inspection .........................................1338
Removal and Installation .....................................1338
AUTOMATIC SPEED CONTROL DEVICE (ASCD) 1339
System Description ..............................................1339
Component Description .......................................1340
ASCD INDICATOR .................................................1341
Component Description .......................................1341
Wiring Diagram—LHD Models .............................1342
Wiring Diagram—RHD Models ............................1343
Diagnostic Procedure ..........................................1344START SIGNAL ......................................................1345
Wiring Diagram ....................................................1345
Diagnostic Procedure ...........................................1346
MI & DATA LINK CONNECTORS ..........................1348
Wiring Diagram ....................................................1348
SERVICE DATA AND SPECIFICATIONS (SDS) ...1350
General Specifications .........................................1350
Mass Air Flow Sensor ..........................................1350
Engine Coolant Temperature Sensor ...................1350
Fuel Rail Pressure Sensor ...................................1350
Glow Plug .............................................................1350
EGR Volume Control Valve ..................................1350
Crankshaft Position Sensor .................................1350
Camshaft Position Sensor ...................................1350
YD (WITHOUT EURO-OBD)
INDEX FOR DTC ....................................................1351
Alphabetical Index ................................................1351
DTC No. Index .....................................................1353
PRECAUTIONS ......................................................1355
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ..............................................................1355
On Board Diagnostic (OBD) System of Engine ...1355
Precautions ..........................................................1355
Wiring Diagrams and Trouble Diagnosis ..............1358
PREPARATION ......................................................1359
Special Service Tools ...........................................1359
Commercial Service Tools ...................................1359
ENGINE CONTROL SYSTEM ................................1360
System Diagram ..................................................1360
Vacuum Hose Drawing ........................................1361
System Chart .......................................................1362
Fuel Injection Control System ..............................1362
Fuel Injection Timing Control System ..................1364
Air Conditioning Cut Control ................................1364
Fuel Cut Control (At No Load & High Engine Speed) 1364
Crankcase Ventilation System .............................1365
CAN Communication ...........................................1365
BASIC SERVICE PROCEDURE ............................1370
Fuel Filter .............................................................1370
Fuel Pump Learning Value Clearing ....................1370
ON BOARD DIAGNOSTIC (OBD) SYSTEM ..........1372
DTC and MI Detection Logic ................................1372
Diagnostic Trouble Code (DTC) ...........................1372
Freeze Frame Data ..............................................1373
NATS (Nissan Anti-theft System) .........................1373
Malfunction Indicator (MI) ....................................1373
Relationship Between MI, DTC, CONSULT-II and
Driving Patterns ...................................................1376
TROUBLE DIAGNOSIS .........................................1378
Trouble Diagnosis Introduction ............................1378
DTC Inspection Priority Chart ..............................1381
Basic Inspection ...................................................1382
Symptom Matrix Chart .........................................1387
Engine Control Component Parts Location ..........1391
Circuit Diagram ....................................................1396
ECM Harness Connector Terminal Layout ...........1398

EC-18 Diagnostic Procedure ..........................................1638
Component Inspection .........................................1640
Removal and Installation .....................................1640
DTC P2228, P2229 BARO SENSOR .....................1641
Description ...........................................................1641
On Board Diagnosis Logic ...................................1641
DTC Confirmation Procedure ..............................1641
Diagnostic Procedure ..........................................1642
GLOW CONTROL SYSTEM ..................................1643
Description ...........................................................1643
Wiring Diagram ....................................................1644
Diagnostic Procedure ..........................................1646
Component Inspection .........................................1650
Removal and Installation .....................................1650
EGR VOLUME CONTROL SYSTEM .....................1651
Description ...........................................................1651
CONSULT-II Reference Value in Data Monitor Mode
1652
Wiring Diagram ....................................................1653
Diagnostic Procedure ..........................................1655
Component Inspection .........................................1656
Removal and Installation .....................................1658
TC BOOST CONTROL SOLENOID VALVE ..........1659
Description ...........................................................1659
Wiring Diagram ....................................................1660
Diagnostic Procedure ..........................................1661
Component Inspection .........................................1663
Removal and Installation .....................................1663
BRAKE SWITCH ....................................................1664
Description ...........................................................1664
CONSULT-II Reference Value in Data Monitor Mode
1664
Wiring Diagram ....................................................1665
Diagnostic Procedure ..........................................1667
Component Inspection .........................................1671
PNP SWITCH .........................................................1673
Description ...........................................................1673
CONSULT-II Reference Value in Data Monitor Mode
1673Wiring Diagram ....................................................1674
Diagnostic Procedure ...........................................1675
PSP SWITCH ..........................................................1677
Component Description .......................................1677
CONSULT-II Reference Value in Data Monitor Mode
1677
Wiring Diagram ....................................................1678
Diagnostic Procedure ...........................................1679
Component Inspection .........................................1680
Removal and Installation ......................................1681
FUEL TRANSPORT PUMP ....................................1682
Description ...........................................................1682
Wiring Diagram ....................................................1683
Diagnostic Procedure ...........................................1685
Component Inspection .........................................1689
Removal and Installation ......................................1689
AUTOMATIC SPEED CONTROL DEVICE (ASCD) 1690
System Description ..............................................1690
Component Description .......................................1691
ASCD INDICATOR .................................................1692
Component Description .......................................1692
Wiring Diagram—LHD Models .............................1693
Wiring Diagram—RHD Models ............................1694
Diagnostic Procedure ...........................................1695
START SIGNAL ......................................................1696
Wiring Diagram ....................................................1696
Diagnostic Procedure ...........................................1697
MI & DATA LINK CONNECTORS ..........................1699
Wiring Diagram ....................................................1699
SERVICE DATA AND SPECIFICATIONS (SDS) ...1701
General Specifications .........................................1701
Mass Air Flow Sensor ..........................................1701
Engine Coolant Temperature Sensor ...................1701
Fuel Rail Pressure Sensor ...................................1701
Glow Plug .............................................................1701
EGR Volume Control Valve ..................................1701
Crankshaft Position Sensor .................................1701
Camshaft Position Sensor ...................................1701