2005 MITSUBISHI LANCER clutch

catalytic converter climate settings oil reset oil additives headlamp fuel type

Page 1 of 788

MITSUBISHI LANCER 2005 Workshop Manual GROUP INDEX
00General . . . . . . . . . . . . . . . . . . . . . . . .
11Engine. . . . . . . . . . . . . . . . . . . . . . . . .
12Engine Lubrication . . . . . . . . . . . . . .
13Fuel . . . . . . . .

GROUP INDEX
00General . . . . . . . . . . . . . . . . . . . . . . . .
11Engine. . . . . . . . . . . . . . . . . . . . . . . . .
12Engine Lubrication . . . . . . . . . . . . . .
13Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .
14Engine Cooling . . . . . . . . . . . . . . . . .
15Intake and Exhaust . . . . . . . . . . . . . .
16Engine Electrical . . . . . . . . . . . . . . . .
17Engine and Emission Control . . . . .
21Clutch . . . . . . . . . . . . . . . . . . . . . . . . .
22Manual Transmission . . . . . . . . . . . .
23Automatic Transmission. . . . . . . . . .
26Front Axle . . . . . . . . . . . . . . . . . . . . . .
27Rear Axle . . . . . . . . . . . . . . . . . . . . . .
31Wheel and Tyre . . . . . . . . . . . . . . . . .
32Power Plant Mount . . . . . . . . . . . . . .
33Front Suspension . . . . . . . . . . . . . . .
34Rear Suspension . . . . . . . . . . . . . . . .
35Service Brakes . . . . . . . . . . . . . . . . . .
36Parking Brakes . . . . . . . . . . . . . . . . .
37Power Steering . . . . . . . . . . . . . . . . .
42Body . . . . . . . . . . . . . . . . . . . . . . . . . .
51Exterior . . . . . . . . . . . . . . . . . . . . . . . .
52 . . . . . . . . . .
54Chassis Electrical . . . . . . . . . . . . . . .
55 . . . . . . .
70Component Locations. . . . . . . . . . . .
80Configration Diagrams . . . . . . . . . . .
90Circuit Diagrams . . . . . . . . . . . . . . . .

LANCER /
LANCER WAGON
WORKSHOP MANUAL
FOREWORD
This Workshop manual contains procedures for
service mechanics, including removal, disassembly,
inspection, adjustment, reassembly and installation.
Use the following manuals in combination with this
manual as required.
TECHNICAL INFORMATION MANUAL
PYME0302
PYME0302-A
WORKSHOP MANUAL
CHASSIS GROUP PWME0302
BODY REPAIR MANUAL
PBME0302
PBME0302-A
PARTS CATALOGUE
B606K005A_
All information, illustrations and product descriptions
contained in this manual are current as at the time of
publication. We, however, reserve the right to make
changes at any time without prior notice or obligation.
Mitsubishi Motors Corporation May 2004
Heater, Air Conditioner and
Ventilation Interior and Supplemental
Restraint System (SRS)

Page 83 of 788

MITSUBISHI LANCER 2005 Workshop Manual STARTING SYSTEM
ENGINE ELECTRICAL16-19
STARTING SYSTEM
GENERAL INFORMATIONM1162000100202
If the ignition switch is turned to the "START"
position, current flows in the pull-in and holding coils
prov

Page 86 of 788

MITSUBISHI LANCER 2005 Workshop Manual STARTING SYSTEM
ENGINE ELECTRICAL16-22
REMOVAL AND INSTALLATION <4G6>M1162001000617
REMOVAL SERVICE POINT
<<A>> STARTER ASSEMBLY REMOVAL
Remove the starter assembly from above the
vehicle.
Pre-remova

Page 90 of 788

MITSUBISHI LANCER 2005 Workshop Manual STARTING SYSTEM
ENGINE ELECTRICAL16-26
DISASSEMBLY AND REASSEMBLYM1162001200202
AK201881
14
1211
20
1
15161718191310 2
4
3
5
7
6
8
9
AG
Disassembly steps
1. Screw
<<A>>2. Magnetic switch
3. Screw
4. B

Page 91 of 788
STARTING SYSTEM
ENGINE ELECTRICAL16-27
DISASSEMBLY SERVICE POINTS
<> MAGNETIC SWITCH REMOVAL
CAUTION
Do not clamp the yoke assembly with a vise.
Disconnect the lead from the M terminal of the
magnetic switch.
<> SNAP RING/STOP RING REMOVAL
1. Apply a long socket wrench of an appropriate size
to the stop ring and strike the wrench to drive out
the stop ring toward the pinion gear side.
2. Remove the snap ring with snap ring pliers, then
remove the stop ring and overrunning clutch.
STARTER MOTOR PARTS CLEANING
Never clean in a solvent such starter motor parts
as the magnetic switch, brush holder, and
armature. If they are soaked in a solvent, their
insulation could be impaired. When these parts
require cleaning, wipe off contamination with
cloth.
1. Never soak the drive unit in a solvent. If it is
washed in a solvent, the grease having been
packed in the overrunning clutch at the factory will
be washed out. Wipe the drive unit with cloth if it
requires cleaning.
REASSEMBLY SERVICE POINTS
>>A<< STOP RING/SNAP RING
INSTALLATION
Use a suitable puller to pull the stop ring until it gets
over the snap ring.
INSPECTION M1162001300157
COMMUTATOR
1. Support the armature with a pair of V block and
turn it to measure the runout of the surface not
rubbed by the brushes using a dial gauge.
Standard value: 0.05 mm or less
Limit: 0.1 mm
AK201882
B terminal
M terminal S terminal
AC
AK100883AC
Socket wrench
Stop ring
Pinion Gear
Overrunning
clutch
AK202791
Snap ring
pliersSnap ring
Pinion gear
Overrunning
clutch
AB
AK202911
Overrunning
clutchStop ring
Snap ring Stop ring
AB
AK202712

Page 92 of 788
STARTING SYSTEM
ENGINE ELECTRICAL16-28
2. Measure the diameter of the commutator.
Standard value: 29.4 mm
Limit: 28.8 mm
3. Measure the depth of the undercut between
segments.
Standard value: 0.5 mm
Limit: 0.2 mm
BRUSH HOLDER
Push the brush into the brush holder to make sure
that the spring is working on the brush.
If the spring is not working, replace the brush holder.
OVERRUNNING CLUTCH
1. Make sure that the pinion cannot be turned
counterclockwise and can be turned clockwise
freely.
2. Check the pinion for abnormal ware and damage.
BRUSHES
1. Check the commutator contacting surface of each
brush for abnormal roughness. Also check the
height of the brush. Replace the brush holder if
the height is lower than the limit.
Limit: 7.0 mm
2. When the contact surface of the brush is rectified
or the brush holder is replaced, recondition the
contact surface with sandpaper wrapped around
the commutator.
ARMATURE COIL
1. Check the armature coil for short circuit as
follows:
AK202715
AK202711
SegmentUndercut
Mica
AB
AK201187
AK202710
Free
Lock
AB
AK202846
Brush
height
AB

Page 127 of 788
21-1
GROUP 21
CLUTCH
CONTENTS
CLUTCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21A
CLUTCH OVERHAUL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21B

Page 448 of 788
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-60
STEP 9. Check the wiring harness between
combination meter connector C-04 (terminal 1
and 2) and earth.
Q: Are the wiring harness between combination meter
connector C-04 (terminal 1 and 2) and earth in
good condition?
YES :
This procedure is complete.
NO : Repair or replace the wiring harness. Check
to see that all meters operate.
ON-VEHICLE SERVICE
SPEEDOMETER CHECKM1543000900423
Adjust the pressure of tyres to the specified level.
(Refer to GROUP 31, On-vehicle Service P.31-7.)
CAUTION
Do not operate the clutch suddenly. Do not
increase/decrease speed rapidly while testing.
1. Set the vehicle onto a speedometer tester and
use wheel chocks to hold the rear wheels.2. To prevent the front wheel from moving from side
to side, attach tension bars to the tie-down hook,
and secure both ends to anchor plates.
3. To prevent the vehicle from moving, attach a chain
or wire to the rear retraction hook, and make sure
the end of the chain or wire is secured.
4. Check if the speedometer indicator range is within
the standard values.
Standard value:
5. If not to the standard value, inspect for proper tyre
size. If not correct, replace the tyres with original
size tyres and retest. If correct, replace the
speedometer. If still not to standard value, replace
the vehicle speed sensor.
TACHOMETER CHECKM1543001000434
1. Attach an external high quality tachometer to the
engine speed detection connector on the harness
side (such as with a paper clip).
AC303798
Connector: C-04

Harness side
AT
AC303814
Connector: C-04

Harness side
AT
AC305135AB
Wheel stopper
Standard indicator
km/h (mph)Allowance range km/h
(mph)
20 (12) 20 − 24 (12 − 15)
40 (25) 40 − 44 (25 − 28)
80 (50) 80 − 85 (50 − 53)
120 (75) 121 − 127 (75 − 79)
160 (100) 162 − 169 (100 − 105)
200 (125) 203 − 211 (126 − 131)
AC001288
Tension bar
Front
Anchor plate
AB
AC305138AB
Engine speed
indicator
Paper clip
Probe for detection
of engine speed

Load next 8 pages

Page: 1-8 9-16 17-24 25-32 32 next >

Search:

wiring diagram suspension checking oil coolant capacity brake rotor TPMS

Popular search:

Intake weight Clutch Air con engine coolant heater lights

All product names, logos, and brands are property of their respective owners. Privacy Policy & Contact Us