2005 MITSUBISHI LANCER length

immobilizer headlights check oil battery capacity auxiliary battery clutch

Page 209 of 788

MITSUBISHI LANCER 2005 Workshop Manual CONTROL LINK, UPPER ARM AND LOWER ARM
REAR SUSPENSION34-9
REMOVAL SERVICE POINTS
<<A>> CONTROL LINK/LOWER ARM
ASSEMBLY REMOVAL
After making a mating mark on the toe adjusting bolt
or camber adjustin

Page 213 of 788
TRAILING ARM ASSEMBLY
REAR SUSPENSION34-13
REMOVAL SERVICE POINTS
<> LIFTING POINT
When removing the trailing arm, move the lifting arm
slightly towards the front of the vehicle so that it will
not be in the way.
<> LOWER ARM ASSEMBLY AND
TRAILING ARM DISCONNECTION
After supporting the lower arm assembly with a jack,
separate the lower arm assembly and trailing arm
connection.
INSTALLATION SERVICE POINT
>>A<< STABILIZER LINK INSTALLATION
Tighten the self-locking nut until the stabilizer link
thread part protruding length meets the standard
value.
Standard value (A): 6 − 8 mm
INSPECTIONM1341002300182
•Check the bushings for wear and deterioration.
•Check the trailing arm for bending or damage.
TRAILING ARM BUSHING
REPLACEMENT
M1341011300221
1. Use the following special tools to drive out the
trailing arm bushing.
•MB990890: Rear Suspension Bushing Base
•MB990947: Lower Arm Bushing Arbor
•MB991816: Bushing Remover and Installer Base
<>9. Lower arm assembly and trailing
arm connection
10. Trailing arm and body connection
11. Trailing armRemoval steps (Continued)
AC006171AC
Trailing arm
AC107126AB
Piece of wood
AC103744
A
AC
AC006172AE
Driving out
MB990890
Trailing armMB990947
MB991816

Page 216 of 788
SHOCK ABSORBER ASSEMBLY
REAR SUSPENSION34-16
REMOVAL SERVICE POINT
<> LOWER ARM BOLT REMOVAL
After supporting the lower arm with a jack, remove
the lower arm bolt.
INSTALLATION SERVICE POINTS
>>A<< SHOCK ABSORBER ASSEMBLY
INSTALLATION
Install the spring seat stepped section so that it
points towards the rear side of the vehicle.
>>B<< STABILIZER LINK INSTALLATION
Tighten the self-locking nut until the stabilizer link
thread part protruding length meets the standard
value.
Standard value (A): 6 − 8 mm
INSPECTIONM1341002600150
•Check the rubber parts for cracks and wear.
•Check the shock absorber for malfunctions, oil
leakage, or abnormal noise.
AC107126AB
Piece of wood
AC304795
AB
Spring seat
stepped section
Rear of
the vehicle
AC103744
A
AC

Page 221 of 788
STABILIZER BAR
REAR SUSPENSION34-21
INSTALLATION SERVICE POINTS
>>A<< STABILIZER
BAR/BUSHING/FIXTURE INSTALLATION
Install the stabilizer bar, the bushings and the fixtures
as illustrated.
>>B<< SELF-LOCKING NUT
INSTALLATION
Tighten the self-locking nut until the stabilizer link
thread part protruding length meets the standard
value.
Standard value (A): 6 − 8 mm
INSPECTIONM1341001400294
•Check the bushings for wear and deterioration.
•Check the stabilizer bar for deterioration or
damage.
•Check all bolts for condition and straightness.
STABILIZER LINK BALL JOINT TURNING
TORQUE CHECK
1. After shaking the ball joint stud several times,
install the nut to the stud and use special tool
preload socket (MB990326) to measure the
turning torque of the ball joint.
Standard value: 0.5 − 1.5 N⋅m
2. If the measured value exceeds the standard
value, replace the stabilizer link.
3. If the measured value is lower than the standard
value, check that the ball joint turns smoothly
without excessive play. If so, it is possible to
re-use that ball joint.
STABILIZER LINK BALL JOINT DUST
COVER CHECK
1. Check the dust cover for cracks or damage by
pushing it with your finger.
2. If the dust cover is cracked or damaged, replace
the stabilizer link.
NOTE: Cracks or damage of the dust cover may
cause damage to the ball joint. When it is
damaged during service work, replace the dust
cover (Refer to P.34-21).
STABILIZER LINK BALL JOINT DUST
COVER REPLACEMENT
M1341010900242
Only when the dust cover is damaged accidentally
during service work, replace the dust cover as
follows:
AC102279AC
Outside of vehicle
Bushing (LH)
Fixture (LH)Identification colourApproximately
9.5 mm
AC103744
A
AC
AC001129
MB990326
AB

Page 252 of 788
STEERING WHEEL
POWER STEERING37-18
REMOVAL SERVICE POINTS
<> COVER REMOVAL
Insert special tool ornament remover (MB990784) at
the indicated position to remove the cover.
NOTE: The special tool can be inserted through the
notch behind the area shown.
<> STEERING WHEEL AND AIR BAG
MODULE ASSEMBLY REMOVAL
1. By sliding section A of the clock spring connector
shown in the illustration in the arrow direction,
disconnect the connector.
2. Loosen the bolt completely. Then, remove the
steering wheel and air bag module assembly.
NOTE: Use a hexagonal bit socket or a hexagonal
wrench having an effective length of 75 mm or
more in the hexagonal section and the diameter of
8 mm or more.
AC006294
AB
MB990784
AC105823
AC304700
AC305145AB
A
Steering
wheel
Air bag module
connector
AC100442
Hexagonal bit socket
AC

Page 254 of 788
STEERING WHEEL
POWER STEERING37-20
<> STEERING WHEEL AND AIRBAG
MODULE ASSEMBLY REMOVAL1. By sliding section A of the clock spring connector
as shown in the illustration in the arrow direction,
disconnect the connector.
2. Loosen the bolt completely. Then, remove the
steering wheel and airbag module assembly.
NOTE: Use a hexagonal bit socket or a hexagonal
wrench having an effective length of 75 mm or
more in the hexagonal section and the diameter of
8 mm or more.
AC105823
AC304700
AC305145AB
A
Steering
wheel
Air bag module
connector
AC211762AC
Hexagonal bit
socket

Page 270 of 788
POWER STEERING GEAR BOX AND LINKAGE
POWER STEERING37-36
>>N<< TIE ROD END/LOCK NUT
INSTALLATION
Screw in the tie rod end to achieve the right and left
length as illustrated. Lock with the lock nut.
NOTE: The lock nuts must be tightened securely
only after the steering gear is installed to the vehicle
and toe-in is adjusted.
>>O<< GEAR MOUNTING RUBBER
INSTALLATION
Install the gear mounting rubber to the rack housing
so that the distance is as shown in the illustration.
TIE ROD END BALL JOINT DUST COVER
REPLACEMENT
M1372008200327
If the dust cover is damaged accidentally during
service work, replace the dust cover as follows:
1. Apply specified grease to the lip and inside of the
dust cover.
Specified grease:
Multipurpose grease SAE J310, NLGI No.2 or
equivalent
2. Drive in the dust cover with special tool front axle
base (MB990776) until it is fully seated.
3. Check the dust cover for cracks or damage by
pushing it with your finger.
AC001011
AM
Lock nut Edge of bellows
assembly groove
180 mm
AC100275
AB
220 mm
AC001012
AB
MB990776

Page 288 of 788
WINDOW GLASS
BODY42-10
WINDOW REPAIRM1422005600027
The windshield, rear window glass, quarter window
glass and tailgate window glass are attached by an
urethane-base adhesive to the window frame. This
adhesive provides improved glass holding and
sealing, and also gives body openings a greater
structural strength.
ITEMS
HANDLING OF AUTO WINDOW SEALER
Keep the sealant in a cool place, not exposed to the
direct rays of the sun. Do not place any heavy article
on the sealant nor press it, otherwise it will become
deformed. Avoid storing the sealant for more than 6
months, because it will lose its sealing effect.
BODY PINCH-WELD FLANGE SERVICING
Before servicing the body pinch-weld flange, remove
old adhesive completely. If the flange requires
painting, bake it after painting is completed. Name Remark
Adhesive 3M ATD Part No.8609 Super Fast Urethane Auto Glass Sealant or
equivalent
Primer 3M ATD Part No.8608 Super Fast Urethane Primer or equivalent
Spacers Available as service part
Dam Available as service part
Anti-rust solvent (or Tectyl
506T.Valvoline Oil Company)For rust prevention
Isopropyl alcohol For grease removal from bonded surface
Steel piano wire Dia. × length... 0.6mm × 1m For cutting adhesive
Glass adhesive knife For cutting adhesive
Adhesive gun For pressing-out adhesive

Page: < prev 1-8 9-16 17-24

Search:

ECU ad blue spare tire location fuse box diagram coolant reservoir oil

Popular search:

ignition wheel bolt torque drain bolt hood open brake rotor Hub nut exterior

All product names, logos, and brands are property of their respective owners. Privacy Policy & Contact Us