2005 MITSUBISHI LANCER length

GENERAL INFORMATION
FRONT SUSPENSION33-2
GENERAL INFORMATION
M1332000100407
The front suspension is a McPherson strut with coil
spring. The shock absorber is gas-filled hydraulic
double-acting type.
CONSTRUCTION DIAGRAM
SPECIFICATIONS
COIL SPRING
NOTE: .
•The*mark indicates optional item.
AC304023
AC304022
AC304754
Lower arm assembly
Front axle No.1
crossmember Stabilizer bar
Strut (shock absorber) Coil spring
AB

Strut cover Strut damper
Strut damper
Item Sedan Wagon
Comfort Sport Comfort Sport
Wire diameter mm 13 13 13 <1600-M/T>
14 1600-A/T,
2000>14
13 <1600>
*
14 <2000>*
Average diameter mm 160 160 160 160
Free length mm 330 321 330 <1600-M/T>
338 <1600-A/T>
338 <2000>314 <1600>
321 <2000>
330 <1600>
*
338 <2000>*

SERVICE SPECIFICATIONS
FRONT SUSPENSION33-3
SERVICE SPECIFICATIONS
M1332000300586
NOTE: *: difference between right and left wheels must be less than 30'
LUBRICANT
M1332000400152
ItemStandard value
Toe-in At the centre of tyre tread mm 1 ± 2
Toe-angle (per wheel) 0°03' ± 06'
Toe-out angle on turns (inner wheel when outer wheel at 20°)21°42' ± 1°30'
Steering angle Inner wheel Comfort 39°30' ± 1°30'
Sport (LH drive vehicles) 33°40' +1°00'/-2°00'
Sport (RH drive vehicles) 37°00' +1°00'/-2°00'
Outer wheel (reference) Comfort 32°30'
Sport (LH drive vehicles) 28°46'
Sport (RH drive vehicles) 30°00'
Camber Comfort 0°05' ± 30'*
Sport -0°05' ± 30'*
Caster Comfort 2°45' ± 30'*
Sport 2°55' ± 30'*
Kingpin inclination Comfort 12°30' ± 1°30'
Sport 12°40' ± 1°30'
Lower arm ball joint rotation starting torque N⋅m0 − 3.9
Protruding length of stabilizer link thread part mm 22 ± 1.5
Item Specified lubricant Quantity
Lower arm ball joint Lip portion of ball joint cover Multipurpose grease SAE J310,
NLGI No.2 or equivalentAs required
Inside of ball joint cover

STRUT ASSEMBLY
FRONT SUSPENSION33-9
DISASSEMBLY SERVICE POINTS
<> STRUT NUT (SELF-LOCKING NUT)
REMOVAL
CAUTION
•Install special tool arm set (MB991238) evenly,
and so that the maximum length will be
attained within the installation range.
•Do not use an impact wrench to tighten the
bolt of special tool spring compressor body
(MB991237), otherwise the special tool will
break.
1. Use following special tools to compress the coil
spring.
•MB991237: Spring Compressor Body
•MB991238: Arm Set
WARNING
Do not use an impact wrench to remove the
strut nut (self-locking nut). Vibration of the
impact wrench will cause special tools
(MB991237 and MB991238) to slip and cause
personal injury.
2. Use following special tools to secure the strut, and
then remove the strut nut (self-locking nut).
•MB991681: Wrench
•MB991682: Socket
<> STRUT DISPOSAL
WARNING
Wear goggles when drilling to protect your
eyes from flying metal debris.
The gas must be discharged from the strut before
discarding it. Place the strut horizontally with its
piston rod extended. Then drill a hole of
approximately 3 mm in diameter at the location
shown in the illustration and discharge the gas.
REASSEMBLY SERVICE POINTS
>>A<< SPRING UPPER SEAT
INSTALLATION
If the spring upper seat peeled off the pad, adhere
the seat and the pad with a double-sided tape.
AC001085 AB
MB991238
MB991237
AC006091 AB
MB991681 MB991682
AC001087
AC304396AB
Seat
Pad