2005 MITSUBISHI LANCER Transmission

COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-38
TECHNICAL DESCRIPTION (COMMENT)
The engine-ECU and its associated components, the
combination meter assembly, the wiring harness, or
the connector(s) may be defective.
TROUBLESHOOTING HINTS
•Malfunction of the vehicle speed sensor
•Malfunction of the engine-ECU
•Malfunction of the combination meter assembly
•The wiring harness or connectors may have
loose, corroded, or damaged terminals, or
terminals pushed back in the connector.
DIAGNOSIS PROCEDURE
STEP 1. MUT-II/III actuator test
(1) Connect the MUT-II/III to the diagnosis connector.(2) Use the MUT-II/III to enter simulated vehicle
speed.
Q: Does the speedometer show that simulated vehicle
speed?
YES :
Go to Step 6.
NO : Go to Step 2.
STEP 2. Check the output shaft speed sensor.
(MUT-II/III diagnosis code)
(1) Connect MUT-II/III to the diagnosis connector.
(2) Turn the ignition switch to the "ON" position.
(3) Read the automatic transmission system
diagnosis code.
Q: Is automatic transmission system diagnosis code
23 set?
YES :
Refer to P.23A-38.
NO : Go to Step 3.
AC304777
Steering shaft
AB
MB991502

AC304950
MB991911
16-PIN
MB991827 MB991824
AB

AC304777
Steering shaft
AB
MB991502

AC304950
MB991911
16-PIN
MB991827 MB991824
AB

ON-VEHICLE SERVICE
HEATER, AIR CONDITIONER AND VENTILATION55-76
FAN CONTROL RELAY CONTINUITY
CHECK
IDLE-UP OPERATION CHECK
M1552001600371
1. Before inspection and adjustment, set vehicle in
the following condition:
•Engine coolant temperature: 80 − 90 °C•Lamps, electric cooling fan and accessories: Set
to OFF
•Transmission: Neutral ("N" or "P" for vehicles with
A/T)
•Steering wheel: Straightforward
2. Check whether or not the idle speed is the
standard value. <1300, 1600> Refer to GROUP
13A, On-vehicle Service − Basic Idle Speed
Adjustment P.13A-387.
<2000> Refer to GROUP 13B, On-vehicle Service
− Basic Idle Speed Adjustment P.13B-324.
Standard value: 750 ± 50 r/min
3. When the A/C is running after turning the A/C
switch to ON, and the blower switch to the 3(MH)
or 4(HI) position, check to be sure that the idle
speed is at the standard value.
Standard value: 850 ± 50 r/min
NOTE: It is not necessary to make an adjustment,
because the idling speed is automatically
adjusted by the ISC system. If, however, a
deviation from the standard value occurs for some
reason, check the ISC system.
CLEAN AIR FILTER REPLACEMENT
PROCEDURE
M1552020100030
1. Remove the glove box (Refer to GROUP 52A,
Instrument Panel P.52A-2).
2. Remove the two screws as shown, and replace
the clean air filter.
3. Install the glove box. Battery voltage Tester
connectionSpecified
condition
Not applied 2 − 4 Open circuit
•Connect
terminal 1 to
the positive
battery
terminal
•Connect
terminal 3 to
the negative
battery
terminal2 − 4 Less than 2
ohms
AC305307
Fan control relay
13
4 2
3 4
1 2
AC
AC305114AB
Air filter
Instrument panel

DIODE
COMPONENT LOCATIONS70-13
DIODE
M1701000900223
AC208684
D
AD
A/T control solenoid
valve assembly connector
Inhibitor switch
A/T control solenoid
valve assembly
Transmission
assembly
AC300441
AC301240
Diode

AD

80-1
GROUP 80
CONFIGURATION
DIAGRAMS
CONTENTS
OVERALL CONFIGURATION
DIAGRAM. . . . . . . . . . . . . . . . . . . . . .80-2
OVERALL WIRING DIAGRAM
. . . . . . . . . . . . . . . . . . . . 80-2
OVERALL WIRING DIAGRAM
. . . . . . . . . . . . . . . . . . . . 80-3
OVERALL WIRING DIAGRAM
. . . . . . . . . . . . . . . . . . . 80-4
OVERALL WIRING DIAGRAM
. . . . . . . . . . . . . . . . . . . 80-5
ENGINE COMPARTMENT. . . . . . . . .80-6
ENGINE COMPARTMENT . . . . . . . 80-6
ENGINE COMPARTMENT . . . . . . 80-7
ENGINE AND TRANSMISSION. . . . .80-8
ENGINE AND TRANSMISSION
<4G1-MPI (LHD) > . . . . . . . . . . . . . . . . . . . 80-8
ENGINE AND TRANSMISSION
<4G1-MPI (RHD) > . . . . . . . . . . . . . . . . . . . 80-10
ENGINE AND TRANSMISSION
<4G6-MPI (LHD) > . . . . . . . . . . . . . . . . . . . 80-12
ENGINE AND TRANSMISSION
<4G6-MPI (RHD) > . . . . . . . . . . . . . . . . . . . 80-14
DASH PANEL . . . . . . . . . . . . . . . . . . .80-16
DASH PANEL . . . . . . . . . . . . . . . . . 80-16
DASH PANEL . . . . . . . . . . . . . . . . . 80-19
FLOOR AND ROOF . . . . . . . . . . . . . .80-22
FLOOR AND ROOF . . . . 80-22
FLOOR AND ROOF . . . . 80-23
FLOOR AND ROOF . . . 80-24
FLOOR AND ROOF . . . 80-25
DOOR . . . . . . . . . . . . . . . . . . . . . . . . .80-26
DOOR . . . . . . . . . . . . . . . . . . . . . . . 80-26
DOOR . . . . . . . . . . . . . . . . . . . . . . . 80-27
TRUNK
(LUGGAGE COMPARTMENT). . . . . .80-28
TRUNK (LUGGAGE COMPARTMENT)
. . . . . . . . . . . . . . . . . . . . 80-28
TRUNK (LUGGAGE COMPARTMENT)
. . . . . . . . . . . . . . . . . . . . 80-29
TAILGATE. . . . . . . . . . . . . . . . . . . . . .80-30
TAILGATE . . . . . . . . . . 80-30
TAILGATE . . . . . . . . . . 80-31

ENGINE AND TRANSMISSION
CONFIGURATION DIAGRAMS80-8
ENGINE AND TRANSMISSION
ENGINE AND TRANSMISSION <4G1-MPI (LHD) >M1801000400689
NOTE: On A/T only, the standard routing positions
for the corrugated tube and wiring harness are
marked by*.
AC301128
B-02
B-03B-04B-05
B-22
B-23 B-24 B-25 B-26Control wiring
harnessB-01
Connector colour
code
B : Black
BR : Brown
G : Green
GR : Gray
L : Blue
None : Milk white
O : Orange
R : Red
V : Violet
Y : Yellow*
Connector
symbol
-01
thru
-26B
Earth cable
AB
9
10
11
13
B-06B-07
B-09
B-10X
B-15X
B-16X
B-17X
B-18
Battery wiring
harness
B-19
B-20
B-21
*
B-01 (5-GR) Windshield wiper motor
B-02 (2-GR) Fuel injector 1
B-03 (2-GR) Fuel injector 2
B-04 (2-GR) Fuel injector 3
B-05 (2-GR) Fuel injector 4
B-06 (3-GR) Throttle body throttle sensor
B-07 (3-B) Vehicle speed sensor
B-09 (2-GR) Brake fluid level indicator switch
B-10X (1) Engine speed detection connector
B-15X (4) A/T control relay
B-16X (4) Engine control relay
B-17X (4) A/C compressor relay
B-18 (6-B) Control wiring harness and battery wiring
harness combination
B-19 (10-GR) A/T control solenoid valve assemblyB-20 (10-B) Inhibitor switch
B-21 (4-B) Engine control oxygen sensor (Front)
B-22 (1) Starter
B-23 (1-B) Starter
B-24 (1-B) Engine oil pressure switch
B-25 (1) Alternator
B-26 (4-GR) Alternator