2005 MITSUBISHI LANCER EVOLUTION IX timing belt

ENGINE – TIMING BELT, TIMING BELT B
11-23
 
D


Removing timing belt B
Caution
If planning to re-use a timing belt B, ensure that it will be
refitted the same way round, by marking the back of the belt
with chalk arrows indicating the direction of movement.
Fitting guidelines



A 
Fitting timing belt B and the timing belt B tensioner
1. Check that the timing marks for the crankshaft sprocket and the
balancer shaft sprocket are aligned.
2. Fit timing belt B onto the crankshaft sprocket and the balancer
shaft sprocket. Ensure that the side of the belt under tension is
not slack.
3. As a temporary step, fit the timing belt B tensioner pulley so that
its centre is to the upper left of the centre of the mounting bolt,
and so that the flange of the pulley is facing towards the front of
the engine.
4. Adjust the tension of timing belt B.



B 
Adjusting the tension of timing belt B
1. Hold the timing belt B tensioner between fingertips and in the
direction of the arrows, apply tension torque (3.0 ± 0.4 N·m) to
timing belt B until the side of the belt under tension becomes
taught. In this condition, tighten the mounting bolt to the
specified torque, and fit the tensioner.
Tightening torque: 19 ± 3 N·m
Caution
When tightening the mounting bolt, ensure that the
tensioner does not turn round with it. If the tensioner turns
with the mounting bolt, it could cause the tension in the belt
to become too high.
timing marks
balancer shaft
sprocket
crankshaft sprocket
side of belt
under tension
timing
marks
centre of the
pulley
centre of the
mounting bolt

ENGINE – TIMING BELT, TIMING BELT B11-24
2.
(1) As shown in the diagram, apply a force of about 100N to the
middle of the belt between the sprockets (indicated by the
arrow), and check that the amount of give is as specified.
Specified values:
5~7mm
5~7mm
(2) If the specified values are not met, readjust the tension of the
belt.
3.
(1) Connect the special belt tension meter set (MB991668) to the
MUT-II/III.
(2) Connect the special battery harness (MB991704) to the MUT-
II/III, and also connect it to the batteries.
(3) Give the crankshaft two turns in a clockwise direction, and check
that the No.1 cylinder is in the top dead centre position, and that
the timing marks on each sprocket are aligned.
(4) Select the “belt tension measurement” option from the display
on the MUT-II/III.
(5) As shown in the diagram hold the special belt tension meter set
(MB991668) in the middle of the belt between the sprockets
(indicated by the arrow), 10~20mm away from the outer side of
the belt and vertically to the belt (not leaning more than ±15°
away from vertical).
(6) As shown in the diagram, lightly pull the middle of the belt
between the sprockets (indicated by the arrow) using fingertips
and check that the vibration frequency of the belt is within the
limits specified.
Specified values: 76 ~ 92 Hz
Caution
(1) The meter may give an incorrect reading if the
microphone is affected by a strong wind, or if there are
loud noises nearby, while testing is taking place.
(2) The meter may give an incorrect reading if testing is
performed while the microphone is touching the belt.
(7) If the specified values are not met, readjust the tension of the
belt.
approx. 100 N
amount of
give
pull lightly with fingertips

ENGINE – TIMING BELT, TIMING BELT B
11-25



C 
Fitting the crankshaft sensing blade and the
crankshaft sprocket
1. Clean, and remove any grease from the crankshaft sensing
blade, the crankshaft sprocket, and the surface of the crankshaft
to which the crankshaft sprocket will be fitted.
2. Fit the crankshaft sensing blade and the crankshaft sprocket in
the direction shown in the diagram.
3. Clean the screw hole in the crankshaft.
4. Place the washer with the larger surface side in the direction as
shown in the diagram, and fit it to the crankshaft bolt.
5. Apply a small quantity of engine oil to the top and to the screw
thread parts of the crankshaft bolt.
6. In the same way as when it was removed, hold the crankshaft
sprocket using the special tool, and tighten the crankshaft bolt to
the specified torque.
Tightening torque: 167 N·m



D 
Fitting the auto-tensioner
1. If the auto-tensioner rod remains in an extended state, install it
using the following procedure.
(1) Using a press or a vice, slowly compress the auto-
tensioner rod and align the rod with setting hole A and the
tensioner cylinder with setting hole B.
Caution
If the speed of compression is too fast, there is a
chance that the rod may break, so carry out this
operation slowly.
(2) Insert a wire or pin into the aligned holes.
Note
If a brand new or a replacement auto-tensioner is being
used, use a pin to set the auto-tensioner in place.
2. Fit the auto-tensioner into the engine and tighten the mounting
bolt to the specified torque. Do not remove the wire or pin until
the tension of the timing belt has been adjusted.
Tightening torque: 23 ± 3 N·m



E 
Fitting the tensioner pulley
As a temporary step, fit the tensioner pulley as shown in the
diagram.
Front of engine
washer
crankshaft sprocket
clean
here
crankshaft
crankshaft boltcrankshaft
sensing
blade
remove
grease
wire or pin
tensioner pulley holes

ENGINE – TIMING BELT, TIMING BELT B11-26



F 
Fitting the timing belt
1. Check that all the timing marks for the camshaft sprocket, the
crankshaft sprocket and the oil pump sprocket are aligned.
2. After the timing marks for the oil pump sprocket have been
aligned, remove the plug from the cylinder block and insert a
posidrive (+) with a diameter of 8 mm into the plug hole. Check
that more than 60 mm of the shaft of the screwdriver can be
inserted. If the screwdriver strikes the balancer shaft and can
only be inserted to a depth of 20 ~ 25 mm, turn the sprocket one
complete turn, realign the timing marks, and check that more
than 60 mm of the screwdriver can be inserted. Do not remove
the screwdriver until the timing belt has been fitted.
3. Install the timing belt in accordance with the following guidelines
so that the side that is under tension does not get slack.
(1) Fit the timing belt around the crankshaft sprocket first, then
the oil pump sprocket and then fit it around the idler pulley.
(2) Fit the timing belt around the camshaft sprocket (exhaust
side) and hold it in place with a paper clip at the position
shown in the diagram.
timing marks
camshaft
sprocket (inlet
side)
timing
marks
crankshaft
sprocket
camshaft
sprocket
(exhaust
side)
timing
marks
oil pump
sprocket
plug
more than
60 mm
screwdriver
balancer shaft
camshaft
sprocket (inlet
side)
tensioner pulley
crankshaft
sprocket
camshaft
sprocket
(exhaust side)
idler
pulley
oil pump
sprocket
paper
clip

ENGINE – TIMING BELT, TIMING BELT B
11-27
(3) Use a wrench to align the timing marks on the rocker cover and
the camshaft sprocket, and whilst doing so, fit the timing belt
around the camshaft sprocket (inlet side) and hold it in place
with a paper clip at the position shown in the diagram.
(4) Fit the timing belt around the tensioner pulley.
(5) Remove the two paper clips.
Caution
After the timing belt has been installed, apply some force in
an anti-clockwise direction to the camshaft sprocket and
check once more that all the timing marks are in the correct
position when the side of the belt under tension is taught.
4. Using the special wrench for the tensioner pulley socket
(MD998767), tense the timing belt by turning the tensioner
pulley in the direction shown in the diagram, and temporarily
tighten the mounting bolt for the tensioner pulley.
5. Check that all the timing marks are aligned.
6. Remove the screwdriver, and replace the plug.
7. Adjust the tension of the timing belt.



G 
Adjusting the tension of the timing belt
1. Remove the rubber plug from the rear cover of the timing belt
and put the special adjusting bolt (MD998738) in position.
Slowly twist the adjusting bolt a little at a time, so that the wire
or pin inserted when fitting the auto-tensioner, only moves a
little.
Caution
There is a possibility that the wire or pin inserted in the
auto-tensioner may break if the adjusting bolt is twisted
with a spanner or a similar tool, so it must be twisted by
hand.
2. Turn the crankshaft a quarter turn in an anti-clockwise direction.
3. Turn the crankshaft in a clockwise direction, realign all the timing
marks and set the No.1 cylinder in the top dead centre position.
4. Loosen the mounting bolt for the tensioner pulley which had
been temporarily tightened.paper clips

ENGINE – TIMING BELT, TIMING BELT B, ENGINE ASSY11-28
5. Using the special wrench for the tensioner pulley socket
(MD998767) or a torque wrench, apply tension torque (3.5 N·m)
to the timing belt in the direction shown in the diagram, and
tighten the mounting bolt for the tensioner pulley to the specified
torque.
Tightening torque: 48 ± 5 N·m
Caution
When tightening the installed bolt, take care that the
tensioner pulley does not turn around with it. If the pulley
does turn around with the bolt, the tension of the belt will
become too strong.
6. Remove the wire or pin which had been inserted when the auto-
tensioner was fitted.
7. Remove by hand the special adjusting bolt (MD998738) which
had been fitted in step 1.
8. Turn the crankshaft two complete turns in a clockwise direction,
and leave it for about 15 minutes.
9. Reinsert the wire or pin which had been removed in step 6, and
check that it can be easily pulled out again.
If the wire or pin can be easily pulled out the tension of the
timing belt is just right, so the wire or pin should be removed
completely. At this point check that the auto-tensioner rod is not
projecting more than the amount specified.
Specified projection (A): 3.8 ~ 4.5 mm
10. If the wire or pin cannot be easily pulled out, repeat steps 1 to 8
until the tension of the timing belt is just right.
11.Recheck that the timing marks on all of the sprockets are in line.
Caution
If the crankshaft bolt is turned in an anti-clockwise
direction, the tightening torque of the crankshaft bolt must
be checked, and if it is loose, it must be retightened.
ENGINE ASSY
Removal and fitting
Jobs to be completed before removal and after fitting
•Measures to prevent fuel leaking.
•Check for fuel dripping.
•Removal and refitting of the bonnet.
•Removal and refitting of the strut tower bar.
•Removal and refitting of the valence. (Ref Section 51: Front bumper)
•Checking the tension of the drive belt.
•Adjustment of the axle letter cable.
•Draining and replacing the engine oil.
•Draining and replacing the coolant.
•Removal and refitting of the air cleaner.
•Removal and refitting of air pipe C.
•Removal and refitting of the battery and the battery tray.
•Removal and refitting of the centre cover. (Ref P11-5)
•Removal and refitting of the axle letter cable.
•Removal and refitting of the radiator.
•Removal and refitting of the front exhaust pipe.

13A-16MPI – TROUBLESHOOTING
Check the purge control solenoid valve (Refer to Section
17: Checking the exhaust gas purification system)
MUT-II/III Service data
•No.11 O
2sensor (Ref: P13A-83)*
Refer to the diagnosis code classification table (P13A-6)MUT-II/III diagnosis code
•Is the diagnosis code displayed?
Check the timing of ignition (Ref Section 11, Engine
tuning)
Check the sound made by the injector (using a
soundscope)
Check the crank angle sensor and the fitting of the timing
belt cover
If there is abnormality in the exhaust gases and code
Nos. P0201~P0204 are recorded, check the injector
system
If abnormal sensor data is recorded, carry out inspections
for each diagnosis code in order (Ref: P13A-6)
Replace the purge control solenoid valve
Code No.P0130: O
2sensor system inspection (Ref:
P13A-16)*
Go on to next page.
MUT-II/III Service data
•No.13: Intake air temperature sensor
•No.14: TPS
•No.21: Water temperature sensor
•No.25: Atmospheric pressure sensor
•No.95: MAP sensor
(Ref: P13A-24)

Proceed to OK if all service data levels are normal.
Proceed via NG even if only one of the service data
levels is abnormal.
*: Refer to the 03-1 Service Manual for the Lancer Evolution VIII (No.1036K07)
NO
OK
OK
OK
OK
OK
YES
NG
NG
NG
NG
Inspection procedureFault to be checkedReference page
11
Engine seems hesitant
13A-16Acceleration malfunction
Engine seems to stumble
Engine has a power surge
15Mis-timed ignition13A-18
35Inter-cooler water spray circuit system13A-19
37No.2 waste gate solenoid valve system13A-21
38Air temperature sensor system13A-22
Engine seems hesitant, acceleration malfunction, engine
seems to stumble, engine has a power surgeProbable causes of the malfunction
Probable causes of the malfunction are noted in the right hand
column.•Malfunction of the air/fuel mixing control system
•Malfunction of the ignition system
•Malfunction of the fuel system
•Malfunction of the intake system
•Malfunction of the exhaust gas purification system
•Failure of compression pressure
•Malfunction of the turbocharger system
5. Inspection procedure for each type of fault
Inspection procedure 11
4. Checklist of faults

13A-18MPI – TROUBLESHOOTING
Measure the output wave from
the crank angle sensor and the
cam position sensor (using an
oscilloscope).
•Engine: idling

•Measure the output wave at
the crank angle sensor
connector B-122
•Connect test harness
(MB998478), to the connector,
and take measurements at the
pick-up harness component
•Voltage across earth at 2

•Measure the output wave at
the exhaust cam position
sensor connector B-115
•Connect test harness
(MB991709), to the connector
and take measurements at the
pick-up harness component
•Voltage across earth at 2
OK:The output wave timing
from both sensors is as
shown on P13A-25
(Main points for
oscilloscope testing).Check that the problem has been
solvedTemporary malfunction (Ref
Section 00: Dealing with
temporary malfunctions)
Replace the engine ECU
NO
OK
NG
OK
NG
NG
NG
Repair
Miss-timed ignitionProbable causes of the malfunction
Probable causes of the malfunction are noted in the right
hand column.•Malfunction of the crank angle sensor
•Malfunction of the exhaust cam position sensor
•Malfunction of the timing belt
•Malfunction of the engine ECU
Inspection procedure 15
Refer to the diagnosis code classification table (P13A-6)MUT-II/III Diagnosis code
•Is the diagnosis code displayed?YES
Repair
Replace the crank angle sensor pane
Match up the timing marks on the timing belt
Replace the exhaust cam position sensing cylinder
Temporary malfunction (Ref Section 00: Dealing with
temporary malfunctions)
Check the exhaust cam position sensing cylinder
Check the fitting of the crank angle sensor and the
exhaust cam position sensor
Check the timing marks on the timing belt
Check the crank angle sensor pane
Replace the crank angle sensor
Check that the problem has been solved
Replace the exhaust cam position sensor
Check that the problem has been solved
Replace the engine ECU
OK
OK
OK
NG
OK
NG
NG
NG
OK
OK