one|Windshield Wiper WasherThe multifunction lever controls the windshieldwiper modes, speeds and the windshield washer. For intermittent operation, move the
control up one position. You can then adjust the rotary control to the desired interval
speed. For normal or low wiper speed, move the control up two positions from OFF. For
high speed operation, move the control up three positions from OFF. For windshieldwasher control, pull the end of the lever toward you. A brief pull causes a single swipe
of the wipers without washer fluid. With a quick pull and hold, the wipers will swipe three times with washer
fluid. With a long pull and hold, the wipers will activate washer fluid for up to ten seconds.
two|Speed ControlFor your speed control to work, you must press and release
the ON button. Pressing and releasing the OFF button disengages the system and
turns it off. To set a speed, accelerate to the desired speed and press the SET+ button,
then take your foot off the accelerator pedal. You can Increase speed using speedcontrol by pressing and releasing the SET+ button until you reach the desired speed;
increasing speed by 1 mph (1..6 km/h) with each tap. You can decrease speed in the
same way using the SET button. Pressing the RSM (resume) button will automatically return the vehicle tothe previously set speed. The RSM control will not work if the vehicle speed is below 30 mph (48 km/h) or
if the OFF or CNCL button was pressed. To disengage the speed control, press the OFF or CNCL button orpress the brake pedal.
three|Headlamp Control Turning the headlamp control clockwise to the first
position turns on the parking lamps, instrument panel lamps, license plate lamps andthe tail lamps. Continuing to turn the headlamp control to the second position turns on
the headlamps. To use the autolamp light sensitive, automatic on off control for the
headlamps, turn the headlamp control counterclockwise. To turn autolamps off, turn
the control clockwise to the OFF position. To activate the high beams, simply pull theturn signal lever towards you to the second detent. Pull the lever towards you again to deactivate high
beams. Use the same lever to activate the “Flash to Pass” feature. Pull the lever towards you to the firstdetent to activate and release it to deactivate.
four|Foglamp ControlWith the ignition on, the foglamps can be turned on when
the headlamp control is in the parking lamp, headlamp, or autolamp position and the highbeams are not on. Simply pull the headlamp control toward you to turn on the foglamps.The foglamp indicator light will illuminate. The foglamps will not operate when the highbeams are activated.
Instrument Panel
Driver and Passenger Side Temperature
Set desired cabin temperature with the 1or 4red and blue buttons. Press 1 for driver’s
side, 4for passenger’s side. Recommended
setting is 72°F (22°C) to 75°F (24°C).
Dual Control (if equipped)
Press 10DUAL to engage/disengage separate
passenger side temperature control. For controlswithout a 10DUAL button, press and hold 2
AUTO to engage/disengage separatepassenger
side temperature control.
Automatic Operation
Set desired 1cabin temperature. Press 2AUTO
button for full automatic operation. The systemwill automatically adjust airflow temperature,fan speed, airflow direction, A/C, andrecirculated air based on the selectedtemperature to heat or cool the vehicle to thedesired temperature as soon as possible.
Max A/C Operation
Automatic operation: Press 2AUTO button for
full automatic operation. Do not override A/C or
recirculated air. Set the desired temperature.Override Operation: Select 7air distribution.
Select 8A/C and 9 recirculated air. Use
recirculated air with A/C to provide colder
airflow. Set temperature setting to 60°F
(15.5°C). Initially set to highest fan speed 5,
then adjust to maintain comfort.Manual Override Operation:Press 1to set
desired cabin temperature. Adjust any of thefollowing for personal comfort preferences: 5
fan speed, 7 airflow direction, 8 A/C, and
9 recirculated air. Fan speed, A/C, and
recirculated air overrides will not turn off the
AUTO indicator light. Airflow direction overrides
will turn off the AUTO indicator light.
One Button Airflow Direction Control (if equipped)Press 7repeatedly to select airflow direction.
Defogging / Demisting
Press 3to distribute outside air through the
windshield defroster vents and demister vents.
To reduce humidity buildup in the vehicle,do not drive with the Climate Control turned off. Also, do not drive with recirculated air selectedunless A/C is operating.
Heated Seats (if equipped)
Press 6to cycle through available settings of
high heat (2 lights), low heat (1 light), and off(no lights). 1
2
4
57910
3
686
Climate Control
