2005 Mercury Montego clock

one|Windshield Wiper WasherThe multifunction lever controls the windshieldwiper modes, speeds and the windshield washer. For intermittent operation, move the
control up one position. You can then adjust the rotary control to the desired interval
speed. For normal or low wiper speed, move the control up two positions from OFF. For
high speed operation, move the control up three positions from OFF. For windshieldwasher control, pull the end of the lever toward you. A brief pull causes a single swipe
of the wipers without washer fluid. With a quick pull and hold, the wipers will swipe three times with washer
fluid. With a long pull and hold, the wipers will activate washer fluid for up to ten seconds.
two|Speed ControlFor your speed control to work, you must press and release
the ON button. Pressing and releasing the OFF button disengages the system and
turns it off. To set a speed, accelerate to the desired speed and press the SET+ button,
then take your foot off the accelerator pedal. You can Increase speed using speedcontrol by pressing and releasing the SET+ button until you reach the desired speed;
increasing speed by 1 mph (1..6 km/h) with each tap. You can decrease speed in the
same way using the SET button. Pressing the RSM (resume) button will automatically return the vehicle tothe previously set speed. The RSM control will not work if the vehicle speed is below 30 mph (48 km/h) or
if the OFF or CNCL button was pressed. To disengage the speed control, press the OFF or CNCL button orpress the brake pedal.
three|Headlamp Control Turning the headlamp control clockwise to the first
position turns on the parking lamps, instrument panel lamps, license plate lamps andthe tail lamps. Continuing to turn the headlamp control to the second position turns on
the headlamps. To use the autolamp lightsensitive, automatic onoff control for the
headlamps, turn the headlamp control counterclockwise. To turn autolamps off, turn
the control clockwise to the OFF position. To activate the high beams, simply pull theturn signal lever towards you to the second detent. Pull the lever towards you again to deactivate high
beams. Use the same lever to activate the “Flash to Pass” feature. Pull the lever towards you to the firstdetent to activate and release it to deactivate.
four|Foglamp ControlWith the ignition on, the foglamps can be turned on when
the headlamp control is in the parking lamp, headlamp, or autolamp position and the highbeams are not on. Simply pull the headlamp control toward you to turn on the foglamps.The foglamp indicator light will illuminate. The foglamps will not operate when the highbeams are activated.
Instrument Panel

Additional Features
Memory Feature(If equipped) This feature will allow you to set two positions for
the driver's seat, power mirrors, and adjustable pedals (if equipped). Set the positionby pressing the SET button (indicator will illuminate) then press the 1 or 2 button to
set the position to either Driver 1 or Driver 2. This memory setting can then berecalled when you press the 1 or 2 button, enter Customer Code 1 or 2 on the keypad,
or when you press unlock on the remote entry system (one of your remotetransmitters is associated with Driver 1 and the other transmitter is associated with Driver 2)
.
HomeLink(if equipped) The HomeLink Wireless Control System on the driver’s visor provides a
convenient way to replace up to three handheld transmitters with a single device. This feature will
operate most garage doors, entry gate operators, security systems, and home or office lighting.
For programming, please consult your Owner’s Guide.
Power MirrorsTo adjust your mirrors, rotate the control clockwise to adjust the
right mirror and counterclockwise to adjust the left mirror. Move the control in the
direction you wish to tilt the mirror. Then rotate the control to the center position to
lock the mirrors in place.
Keyless Entry PadThe keyless entry keypad can be used to lock or unlock the
doors without using a key. It can also control the memory seat, power mirrors, and
adjustable pedals features (if equipped). For more information, please consult yourOwner’s Guide.
AutolockYour vehicle is equipped with an autolock feature. The autolock feature will automatically
lock all doors when your vehicle is in motion and meets a set of conditions, as described in your
Owner’s Guide. Your vehicle comes with this feature enabled. You can enable or disable this featureby following the activation or deactivation procedure outlined in your Owner’s Guide.
Adjustable Pedals(if equipped): The accelerator and brake pedal should only be adjusted when
the vehicle is stopped and the gearshift is in the P (Park) position. Press the top of the control to adjustthe pedals away from you or press the bottom of the control to adjust the pedals toward you.
Reverse Sensing System(if equipped) The Reverse Sensing System (RSS) sounds a tone to warn
the driver of obstacles near the rear bumper when R (Reverse) is selected and the vehicle is moving atspeeds less than 3 mph (5 km/h). The system is not effective at speeds above 3 mph (5 km/h) andmay not detect certain angular or moving objects.

one|Tune/Disc SelectorPress to go up or down
the radio frequency or to select a desired disc.Also use in menu mode to select various settings.
two|LoadPress to begin the CD load
sequence. Press and hold to autoload up to6 CDs.
three|CDPress to enter CD mode. If a CD is
already loaded into the system, the CD willbegin playing where it last ended.
four|On/Off/Volume Control Push to turn
the system ON or OFF. Turn to increase ordecrease volume. If the volume is set above acertain level and the ignition is turned off, the
volume will come back on at a “nominal” levelwhen the ignition switch is turned back on.
five|AM / FMPress to select AM or FM
frequency bands.
six|Seek Function Press to access the
next/previous strong station or track.
seven|Scan FunctionPress for a brief
sampling of radio stations or CD tracks. Pressagain to stop.
eight|CD RewindPress to manually reverse in
a CD track.
nine|CD Fast Forward Press to manually
advance in a CD track.
ten|Setting Memory Preset To set a station:
Press AM/FM to select frequency band; tune toa station, then press and hold a preset buttonuntil the sound returns.
Bass / TreblePress MENU until bass or treble
settings are displayed, adjust using theSEEK control.
Balance / Fade Press MENU until Balance is
displayed, press to adjust the audio betweenthe left and right speakers using the SEEK
control. Press MENU again to display Fade,
press SEEK to adjust audio between the frontand rear speakers.
Setting The Clock Press MENU until SELECT
HOUR or SELECT MINS is displayed. Press the
up/down arrows or SEEK control to adjust the
hours/minutes. Press MENU again todisengage clock mode.
MP3 Track/Folder Mode In Track mode, pressing
SEEK will scroll through all tracks on the disc.
In Folder mode, pressing SEEK will scroll only
through tracks within a selected folder.
4
3
5
6
6
8
10
21
7
9
Premium / Audiophile InDash 6CD Sound System (if equipped)