Page 277 of 442

275 Operation
At the gas station
At the gas station
RefuelingThe fuel filler flap is located on the 
right-hand side of the vehicle towards the 
rear. Locking/unlocking the vehicle with 
the SmartKey automatically locks/unlocks 
the fuel filler flap.
1To open the fuel filler flap
2To insert the fuel filler cap
3Tire pressure table
Turn the engine off by turning the 
SmartKey to position0.
Remove the SmartKey from the starter 
switch.
Warning!
G
Gasoline is highly flammable and poisonous. 
It burns violently and can cause serious 
injury. Whenever you are around gasoline, 
avoid inhaling fumes and skin contact, 
extinguish all smoking materials. Never 
allow sparks, flame or smoking materials 
near gasoline! 
Warning!
G
Flexible Fuel Vehicles only (identified by a 
label reading Premium gasoline or E85 
only! on fuel filler flap):
Ethanol fuel (E85) and its vapors are highly 
flammable, poisonous and burn easily. Etha-
nol fuel can cause serious injuries if ignited 
or if you come into contact with it or inhale 
fumes of it. Avoid inhalation of Ethanol 
fumes and skin contact with Ethanol. Extin-
guish all open flames before fueling. Never 
smoke or create sparks close to Ethanol.
 
     
        
        Page 299 of 442

297 Operation
Vehicle care
Engine cleaning
Prior to cleaning the engine compartment, 
make sure to protect electrical compo-
nents and connectors from the intrusion of 
water and cleaning agents.
Corrosion protection, such as MB Anticor-
rosion Wax, should be applied to the 
engine compartment after every engine 
cleaning. Before applying, all control 
linkage bushings and joints should be 
lubricated. The poly-V-belt and all pulleys 
should be protected from any wax.Vehicle washing
Do not use hot water or wash your vehicle 
in direct sunlight. Only use a mild car wash 
detergent, such as Mercedes-Benz 
approved Car Shampoo.
Thoroughly spray the vehicle with a dif-
fused jet of water. Direct only a very weak 
spray towards the ventilation intake. Use 
plenty of water and rinse the sponge and 
chamois frequently.
Rinse with clear water and thoroughly dry 
with a chamois. Do not allow cleaning 
agents to dry on the finish.
Due to the width of the vehicle, fold in 
exterior rear view mirrors prior to running 
the vehicle through an automatic car wash 
to prevent damage to the mirrors.
In the winter, thoroughly remove all traces 
of road salt as soon as possible.
When washing the underbody, do not 
forget to clean the inner sides of the 
wheels.Ornamental moldings
For regular cleaning and care of very dirty 
chrome-plated parts, use a chrome 
cleaner.
Headlamps, tail lamps, side markers, 
turn signal lenses
Use a mild car wash detergent, such as 
Mercedes-Benz approved Car Shampoo, 
with plenty of water.
To prevent scratches, never apply strong 
force and only use a soft, non-scratchy 
cloth when cleaning the lenses. Do not 
attempt to wipe dirty lenses with a dry 
cloth or sponge. 
     
        
        Page 303 of 442
301  Practical hints
What to do if …
Where will I find ...?
Unlocking/locking in an emergency
Opening/closing in an emergency
Replacing SmartKey batteries
Replacing bulbs
Replacing wiper blades
Flat tire
Battery
Jump starting
Towing the vehicle
Fuses 
     
        
        Page 331 of 442
329 Practical hints
Where will I find ...?
Where will I find ...?
First aid kit
The first aid kit is located in the trunk on 
the left side secured by a hook and loop 
fastener.
1First aid kit
2Hook and loop fastener
Unfasten hook and loop fastener2.
Remove first aid kit1.
Vehicle tool kit
The vehicle tool kit is located in the storage 
compartment underneath the trunk floor.
The following is included:
Towing eye bolt
Wheel wrench
Alignment bolt
Vehicle jack
Spare wheel bolts
Spare fuses
Valve extractor (C 55 AMG only)
Protective wrap (C 55 AMG only)
Collapsible wheel chock
A pair of gloves Removing the vehicle tool kit (except 
C55AMG)
Lift up trunk floor cover and engage 
trunk floor handle in upper edge of 
trunk.
1Retaining screw
2Storage well casing
Loosen retaining screw1 by turning it 
counterclockwise.
Remove storage well casing2.
iCheck expiration dates and contents 
for completeness at least once a year 
and replace missing/expired items.
 
     
        
        Page 333 of 442

331 Practical hints
Where will I find ...?
1Vehicle jack
2Collapsible wheel chock and spare 
wheel bolts
3Towing eye bolt
4Alignment bolt
5Wheel wrench
6Spare fuses and valve extractor
7Electric air pumpVehicle jackThe vehicle jack is located in the storage 
compartment underneath the trunk floor.
Storage position
Remove vehicle jack from its 
compartment.
Push crank handle up.
Warning!
G
The jack is designed exclusively for jacking 
up the vehicle at the jack take-up brackets 
built into both sides of the vehicle. To help 
avoid personal injury, use the jack only to lift 
the vehicle during a wheel change. Never 
get beneath the vehicle while it is supported 
by the jack. Keep hands and feet away from 
the area under the lifted vehicle. Always 
firmly set parking brake and block wheels 
before raising vehicle with jack.
Do not disengage parking brake while the 
vehicle is raised. Be certain that the jack is 
always vertical (plumb line) when in use, 
especially on hills. Always try to use the jack 
on level surface. Make sure the jack arm is 
fully seated in the jack take-up bracket. 
Always lower the vehicle onto sufficient 
capacity jackstands before working under 
the vehicle. 
     
        
        Page 342 of 442
340 Practical hintsUnlocking/locking in an emergencyManually unlocking the transmission gear selector lever
In the case of power failure the transmis-
sion gear selector lever can be manually 
unlocked, e.g. to tow the vehicle.
Slide out the swiveling cup holder 
(page 243).
1Tool
Insert a tool1 (e.g. flat blade 
screwdriver) into the opening.
Perform the following two steps 
simultaneously:
Press tool1 forward in the 
direction of the arrow.
Move gear selector lever from 
positionP.
Remove tool1 from the opening.iThe gear selector lever is locked again 
when moving it to positionP. 
     
        
        Page 352 of 442

350 Practical hintsReplacing bulbsFront turn signal lamp bulb
Turn bulb socket3 with the bulb 
counterclockwise and remove it.
Press gently onto the bulb and turn it 
counterclockwise out of bulb 
socket3.
Press new bulb gently into bulb 
socket3 and turn clockwise until it 
engages.
Place bulb socket3 back into the 
lamp and turn it clockwise.Parking and standing lamp bulb
Press the clamp on housing cover2 
and remove it. 
Pull out bulb socket5 with the bulb.
Pull the bulb out of bulb socket5.
Press the new bulb into bulb socket5.
Press bulb socket5 back into the 
lamp.
Align housing cover2 and press until 
it engages.Side marker lamp 
Carefully slide the lamp towards the 
rear in direction of arrows.
Remove the front end first.
Turn the bulb socket with the bulb 
counterclockwise and remove it.
Pull the bulb out of the bulb socket.
Insert the new bulb into the bulb 
socket.
Place the bulb socket back into the 
lamp and turn it clockwise.
To reinstall the lamp, set the rear end in 
the bumper and let the front end 
engage. 
     
        
        Page 366 of 442

364 Practical hintsJump startingThe battery is located in the engine 
compartment on the right hand side. The 
terminals for jump starting are located in 
front of the battery.
Make sure the two vehicles do not 
touch.
Turn off all electrical consumers.
Apply parking brake.
Shift gear selector lever to positionP 
(manual transmission to Neutral).1Positive terminal of charged battery
2Positive under hood terminal in front of 
discharged battery
3Negative under hood terminal in front 
of discharged battery
4Negative terminal of charged battery
Connect positive terminal1 of the 
charged battery with positive under 
hood terminal2 in front of the 
discharged battery with the jumper 
cables. Clamp cable to charged 
battery1 first.
Start engine of the vehicle with the 
charged battery and run at idle speed.
Connect negative terminal4 of the 
charged battery with negative under 
hood terminal3 in front of the 
discharged battery with the jumper 
cables. Clamp cable to charged 
battery4 first.
Start the engine of the disabled 
vehicle.
You can now again turn on the electrical 
consumers. Do not turn on the lights under 
any circumstances.
Remove the jumper cables first from 
negative terminals4 and3 and then 
from positive terminals1 and2.
You can now turn on the lights.
Have the battery checked at the near-
est authorized Mercedes-Benz Center.
Warning!
G
Keep flames or sparks away from battery. 
Do not smoke. 
Observe all safety instructions and precau-
tions when handling automotive batteries 
(page 284).
!Vehicles with automatic transmission 
and/or 4MATIC:
Do not tow-start the vehicle.