2005 LEXUS LS430 display

AUDIO
261
1Turning the system on and adjusting the volume
(See page 262 for details.)
2Stopping and ejecting a cassette tape
(See page 279 for details.)
3Function buttons
1 6: Station selector buttons
(See page 268 for details.)
SCAN: Scan tuning
(See page 269 or 284 for details.)
4
Display of functions in TAPE or CD mode
:
Side change
(See page 280 for details.)
: DOLBY NR
(See page 279 for details.)
:Rewinding or reversing
(See page 280 for details.)
 :Fast forwarding
(See page 280 for details.)
RPT: Automatic repeat
(See page 280 or 285 for details.)
SKIP: Automatic skip of blank portions of tape
(See page 280 for details.)
:CD selection
(See page 284 for details.)
RAND: Random access
(See page 286 for details.)
5
Radio text
(See page 271 for details.)
6Radio mode: Frequency tuning
(See page 268 or 269 for details.)
TAPE mode: Direct access to a desired program
(See page 281 for details.)
CD mode: Direct access to a desired program
(See page 285 for details.)
7
Cassette tape slot
(See page 279 for details.)
8Tone and balance knobs
(See page 263 for details.)
9Program type/Traffic program
(See page 270 for details.)
10Mode selectors
(See page 262 for details.)
11CD load button
(See page 282 for details.)
12CD slot
(See page 282 for details.)
13Ejecting a CD
(See page 283 for details.)
14Automatic Sound Levelizer (ASL)/Positioning
selector
(See page 264 for details.)

AUDIO
263
20L344
In the “TAPE” or “CD” mode, the applicable functions are
shown in the lowest part of the display. Push the switch
just below to turn on each function.
(b) Tone and balance
How good an audio program sounds to you is largely
determined by the mix of the treble, mid −range, and bass
levels. In fact, different kinds of music and vocal programs
usually sound better with different mixes of treble, mid− range,
and bass.
A good balance of the left and right stereo channels and of the
front and rear sound levels is also important.
Keep in mind that if you are listening to a stereo recording or
broadcast, changing the right/left balance will increase the
volume of one group of sounds while decreasing the volume
of another.
20L357
“BALANCE” knob: Use this knob to adjust the sound
balance between the right and left speakers.
“FADER” knob: Use this knob to adjust the sound balance
between the front and rear speakers.
“BASS” knob: Use this knob to adjust low− pitched tones.
“MID” knob: Use this knob to adjust mid −pitched tones.
“TREBLE” knob: Use this knob to adjust high−pitched tones.

AUDIO
264(c) DSP Control

Automatic Sound Levelizer (ASL)
20L358
When the audio sound becomes difficult to be heard due to
road noise, wind noise, etc. during driving, push the “ASL”
button. The system adjusts to the optimum volume and tone
quality according to the noise level. While the Automatic
Sound Levelizer (ASL) is on, “ASL” appears on the display. 
Positioning selector
20L359a
By selecting the listening position, the system controls the
output timing of the speakers to allow sound to be heard
evenly, creating the ideal music environment.
Each time you push the “POS” button, the position changes as
in the following and the letter displays for 6 seconds on the
screen.
ALL
DRIVER FRONT
REAR

AUDIO
266
20L361a
NOTICE
Do not put any object on the panel or push it hard. Doing
this may damage the panel.
20L362a
Your automatic changer can store up to 6 CDs and play
selected CDs or continuously play all the CDs set in the player.
When you set CDs into the player, make sure their labels face
up. If not, the player will display “ERROR1” and the CD
number.
NOTICE
 Never try to disassemble or oil any part of the CD
player. Do not insert anything except a CD into the
slot.
 Do not insert a CD upon another one, or it will damage
the automatic changer. Insert only one CD into the
slot at a time.

AUDIO
267

The following products may not be playable on your CD
player.
Copy−protected CD
CD− R (CD− Recordable)
CD−RW (CD− Re−writable)
CD−ROM
 Your CD player is intended for use with 12 cm (4.7 in.) CDs
only.
Radio operation
(a) Listening to the radio
20L363
Push these buttons to choose either an AM or FM station.
“AM”, “FM1”, “FM2” or “FM TYPE” appears on the d\
isplay.
If your vehicle is equipped with satellite radio broadcast
system, when you push the “AM·SAT” button, “AM”,
“SAT1”, “SAT2” or “SAT3” station appears on the display. For
details about satellite radio broadcast, see “Radio operation
(XM satellite radio broadcast)” on page 272

AUDIO
268
20L128
Push this button on the upper side to step up the station
band or on the lower side to step down.
Your radio automatically changes to stereo reception when a
stereo broadcast is received. “ST” appears on the display. If
the signal becomes weak, the radio reduces the amount of
channel separation to prevent the weak signal from creating
noise. If the signal becomes extremely weak, the radio
switches from stereo to mono reception. In this case, “ST”
disappears from the display.(b) Presetting a station
20L129
1. Tune in the desired station.
2. Push
one of the station selector buttons ( 16 ) and hold
it until a beep is heard. This sets the station to the button
and the button number ( 16 ) appears on the display.
Each button can store one AM station and two FM stations. To
change the preset station to a different one, follow the same
procedure.
The preset station memory is cancelled when the power
source is interrupted by battery disconnection or a blown fuse.

AUDIO
269
(c) Selecting a station
Tune in the desired station using one of the following methods.
20L130a
Preset
tuning: Push the button ( 1 −6 ) for the station you want.
The button number ( 1− 6 ) and station frequency appear on the
display.
Manual tuning: Push the “TUNE SEEK” button briefly. Each
time you push the button, the radio will step up or down to
another frequency.
Seek tuning: Push the “TUNE SEEK” button and hold it until
you hear a beep. The radio will begin seeking up or down for
a station of the nearest frequency and will stop on reception.
Each time you push the button, the stations will be searched
automatically one after another.
20L139a
To scan all the frequencies: Push the “SCAN” button briefly.
“SCAN” appears on the display. The radio will find the next
station up the band, stay there for a few seconds, and then
scan again. To select a station, push the “SCAN” button a
second time.
To scan the preset stations: Push the “SCAN” button and
hold it until you hear a beep. “P .SCAN” appears on the display.
The radio will tune in the next preset station up the band, stay
there for a few seconds, and then move to the next preset
station. To select a station, push the “SCAN” button a second
time.

AUDIO
270(d) RDS (Radio Data System)
20L364
Program type:
When you push the TYPE “
”
or “” button, the current
program type receiving from the RDS station appears on the
display.
If the radio receives no RDS stations, “NO PTY” appears on the
display.
Each time you push the TYPE “
” or “” button, the program
type changes as in the following:
 ROCK
 EASY LIS (Easy listening)
 CLS/JAZZ (Classical music and jazz)
 R&B (Rhythm and Blues)
 INFORM (Information)
 RELIGION 
MISC
 ALERT (Emergency message)
While you are listening to a program type, you can operate the
“TUNE SEEK” or “SCAN” function.
20L406
Push the “TUNE SEEK” or “SCAN” button. The radio seeks or
scans the station in the relevant program type. (See page 269
for details.)