2005 LEXUS LS430 ignition

STARTING AND DRIVING
304
PARKING BRAKE
31L628
1To set: Fully depress the parking brake pedal.
2To release: Pull the parking brake release lever.
Before leaving your vehicle, firmly apply the parking brake.
CAUTION
Before driving, make sure the parking brake is fully
released and that the parking brake reminder light is off.
HOW TO START THE ENGINE
Before cranking
1. Apply the parking brake firmly.
2. Turn off unnecessary lights and accessories.
3. Put the selector lever in “P”. If you need to restart the engine
while the vehicle is moving, put the selector lever in “N”. A
starter safety device will prevent the starter from operating if
the selector lever is in any drive position.
4. Depress the brake pedal and hold it to the floor until driving
off.
Starting the engine
Before starting the engine, be sure to follow the instructions in
“Before cranking”.
Normal starting procedure
The multiport fuel injection system/sequential multiport fuel
injection system in your engine automatically controls the
proper air −fuel mixture for starting. You can start a cold or hot
engine as follows:
With your foot off the accelerator pedal, crank the engine by
turning the ignition switch to “START”. Release it when the
engine starts.

STARTING AND DRIVING
305
The engine should be warmed up by driving, not in idle. For
warming
up, drive with smoothly turning engine until the engine
coolant temperature is within normal range.
If the engine stalls ...
Simply restart it, using the correct procedure given in normal
starting.
If the engine will not start
See “If your vehicle will not start” on page 400.
NOTICE
 Do not crank for more than 30 seconds at a time. This
may overheat the starter and wiring systems.
 Do not race a cold engine.
 If the engine becomes difficult to start or stalls
frequently, have the engine checked immediately.
AUTOMATIC TRANSMISSION
Your automatic transmission has a shift lock system to
minimize the possibility of incorrect operation. This
means you can only shift out of “P” position when the
brake pedal is depressed with the ignition switch in “ON”
position. ( )
31L320

STARTING AND DRIVING
307
(a) Normal driving
31L321a
 1“P” (Park) position 2“N” (Neutral) position
1. Start the engine as instructed in “How to start the
engine” on page 304.
The transmission must be in “P” or “N” position. The engine wi\
ll
not start in any drive position even if the ignition switch is turned
to “START”.
31L322
 1 Power position 2Normal position
3Snow position
2. Set the driving pattern selector switch to the “Normal”
position.
Your transmission has a driving pattern selector switch which
allows you to select “Power”, “Normal” or “Snow” mode to suit\
your driving condition. For ordinary driving, Lexus
recommends that you use the “Normal” position to improve fuel
economy.
3. For more powerful acceleration and sporty driving, use
the “Power” position.
In the “Power” position, the “ECT PWR” light in the instrument
cluster is on and the transmission is shifted up at higher vehicle
speeds and shifted down more responsively than in the
“Normal” position.
For “Snow” mode, see “Electronic Throttle Control
System” on page 315.

STARTING AND DRIVING
313
(d) Backing up
31L324
 1Brake pedal 2“R” (Reverse) position
1. Bring the vehicle to a complete stop.
2. With the brake pedal held down with your foot, shift the
selector lever to the “R” position.
NOTICE
Never shift into reverse while the vehicle is moving.
When the selector lever is shifted into the “R” position, the
outside rear view mirrors automatically down to help backing
up. For details, see “Power rear view mirror control” on page
231.
Vehicles with rear view monitor system: When the selector
lever is shifted into the “R” position with the ignition switch in\
the “ON” position, rear view monitor system will activate. For
instructions, see “Rear view monitor system” on page 323.

STARTING AND DRIVING
316In the power mode, the “ECT PWR” light in the instrument
cluster is on and the transmission is shifted up at higher vehicle
speeds and shifted down more responsively
than in the normal
mode.
To return to the normal mode, push the driving pattern selector
switch lightly on the “SNOW” side.
Snow mode: For slippery road surfaces such as in snow. In
this mode, the spinning of the rear wheels is controlled
appropriately.
When you push the driving pattern selector switch on the
“SNOW” side, the snow mode is turned on and the “ECT
SNOW” light in the instrument cluster comes on.
To return to the normal mode, push the driving pattern selector
switch on the “SNOW” side again.
When you turn the ignition switch off in the snow mode, the
mode automatically changes to the normal mode.
LEXUS PARK ASSIST SYSTEM
31L354b
 Sensors
The Lexus park assist system will help you to easily park
by detecting any obstacle around your vehicle with
ultrasonic sensors and informing you of the approximate
distance from the vehicle to the obstacle with the
indicators on the display and with beeping sounds.*
This system will operate at a vehicle speed of less than about
10 km/h (6 mph) with the selector lever in a position other than
“P”.
NOTE:
* The volume of the beeps can be changed.
Ask your Lexus dealer for details.

STARTING AND DRIVING
317
31L340
You can use this system in either of the following ways.
Push the main switch of the Lexus park assist system with
the ignition on. A beep sounds for one second. After the
system self− check is performed, the Lexus park assist
system screen appears for 2 seconds.
 Push the main switch of the Lexus park assist system and
turn the ignition on. The Lexus park assist system screen
appears for 2 seconds and a system self −check is
performed. At this time, a beep does not sound.
If an error is detected in the Lexus park assist system while
self−checking, beeps sound and the message appears in the
multi− information display. For details, see “Lexus park assist
system failure warning” on page 319. Up to 4 indicator bars are shown on the front and rear sides of
the vehicle mark and up to 3 indicator arcs are shown on each
corner of the vehicle mark. The number of indicators shows
the approximate range up to the obstacle. The indicator marks
disappear one
−by−one as your vehicle comes closer to the
obstacle. Also, as you get closer to the obstacle, the beeping
interval becomes shorter.
To turn off the system, push the main switch again.
NOTICE
 If an accident should occur, the sensors will be
affected, resulting in a system failure.
 If the indicators remain on the display but you do not
hear a beeping sound, the system may be
malfunctioning. Contact your Lexus dealer.

STARTING AND DRIVING
323
REAR VIEW MONITOR SYSTEM
The rear view monitor system assists the driver by
displaying an image of the rear of the vehicle while
backing up. The displayed image on the screen is a
horizontally reversed mirror image of the inside rear view
mirror.
To display the rear view image on the screen, place the
selector lever in the “R” position when the ignition switch
is in the “ON” position.
If you move the selector lever out of the “R” position, the screen
returns to the previous screen. Operating another function of
the navigation system will display another screen.
The rear view monitor system is a supplemental device
intended to assist back up. When backing up, be sure to check
behind and all around the vehicle visually.
CAUTION
 Never depend on the rear view monitor system
entirely when backing up. Always make sure your
intended path is clear.
Use caution just as you would when backing up any
vehicle.
 Never back up while looking only at the screen. The
image on the screen is different from actual
conditions. Depicted distances between objects and
flat surfaces will differ from actual distances. If you
back up while looking only at the screen, you may hit
a vehicle, a person or an object. When backing up, be
sure to check behind and all around the vehicle
visually and with mirrors before proceeding.
 Do not use the system when the trunk is not
completely closed.
 If the back of the vehicle is hit, the position and
mounting angle of the camera may change. Be sure
to have the camera’s position and mounting angle
checked at your Lexus dealer.
 If the temperature changes rapidly , such as when hot
water is poured on the vehicle in cold weather, the
system may not operate normally.

STARTING AND DRIVING
327
Turning the system on
31L629
To operate the cruise control, push the “ON−OFF” button. This
turns the system on. The indicator light in the instrument
cluster shows that you can now set your desired cruising
speed. Another push on the button will turn the system
completely off.
When the ignition switch is turned off, the “ON −OFF” button is
also automatically turned off. To use the cruise control again,
push the “ON −OFF” button again to turn it on.
CAUTION
To avoid accidental cruise control engagement, keep
the “ONOFF” button off when not using the cruise
control.
Setting operation
31L630
 Each function is described below.
1
Setting at a desired speed.
The transmission must be in the “D” position, or the shift range
position must be “4” (fourth range), “5” (fifth range) o\
r “6” (sixth
range) in the “S” mode before you set the cruise control speed.
Bring the vehicle to the desired speed, press the control lever
downward in the “– SET” direction and release it. This sets the
vehicle at that speed. Now you may take your foot off the
accelerator pedal. If you need acceleration − for example,
when passing − depress the accelerator pedal enough for the
vehicle to exceed the set speed. When you release the
accelerator pe dal, the vehicle will return to the speed set prior
to the acceleration.