2005 LEXUS LS430 ignition

STEERING WHEEL AND MIRRORS
234
156.INSIDE REAR VIEW MIRROR
16L286
Adjust the mirror so that you can just see the rear of your
vehicle in the mirror.
Pushing the switch changes the mode between “AUTO”
and “DAY”.
The indicator comes on when the “AUTO” mode is selected.
“DAY” mode: The mirror surface is normal.
“AUTO” mode: If the mirror detects light from the
headlights of the vehicle behind you, the mirror surface
darkens slightly to reduce the reflected light.
When the inside rear view mirror surface changes, the outside
rear view mirror surfaces will also become darker.
When the ignition switch is turned on, the inside rear view
mirror always turns on in the “AUTO” mode. When the outside air temperature is low, it may take a little
longer for the mirror to darken in response to the detection of
headlights.
CAUTION
Do not adjust the mirror while the vehicle is moving.
Doing so may cause the
driver to mishandle the vehicle
and an accident may occur resulting in death or serious
injuries.

AIR CONDITIONING
239
The automatic air conditioning automatically maintains
the set temperature.
This
air conditioning features automatic fan speed and air flow
control which automatically se lects the most suitable fan
speed and air flow to control the temperature.
The ignition switch must be in the “ON” position.
NOTICE
To prevent the battery from being discharged, do not
leave the air conditioning on longer than necessary
when the engine is not running.
1 Temperature selector
(with the “DUAL” button on; for driver and rear
passengers)
(with the “DUAL” button off; for driver and all
passengers)
2 Passenger side temperature control button
3 Front windshield button
4 Driver side temperature display
(in degrees Fahrenheit or Centigrade)
5 Air intake control button
6 Fan speed display
7 Air flow display
8 Passenger side temperature display
(in degrees Fahrenheit or Centigrade)
9 Center vent vane swing button
10 Air conditioning onoff button
11 Air flow control button
12 Fan speed control button
13 OFF button
14 Automatic control button
15 Separate/dual control button

AIR CONDITIONING
241
The automatic air conditioning automatically maintains
the set temperature.
This
air conditioning features automatic fan speed and air flow
control which automatically se lects the most suitable fan
speed and air flow to control the temperature.
The ignition switch must be in the “ON” position.
NOTICE
To prevent the battery from being discharged, do not
leave the air conditioning on longer than necessary
when the engine is not running.
1 Temperature selector
(with the “DUAL” button on; for driver and rear
passengers)
(with the “DUAL” button off; for driver and all
passengers)
2 Passenger side temperature control button
3 Front windshield button
4 Driver side temperature display
(in degrees Fahrenheit or Centigrade)
5 Fan speed display
6 Air flow display
7 Air intake control button
8 Passenger side temperature display
(in degrees Fahrenheit or Centigrade)
9 Center vent vane swing button
10 Air conditioning onoff button
11 Air flow control button
12 Fan speed control button
13 OFF button
14 Automatic control button
15 Separate/dual control button

AIR CONDITIONING
248
(b) Windshield defogging and defrosting
21L068a
To remove interior fog on the windshield
Push the “FRONT WINDSHIELD” button.
To remove frost or exterior fog on the windshield
1. Place the temperature control button at the maximum
temperature.
2. Push the “FRONT WINDSHIELD” button.
3. Push the fan speed control button on the right side to obtain
a maximum air flow.
4. Leave the “A/C” button off.
When the “FRONT WINDSHIELD” button is pushed while
operating in automatic mode, the air conditioning is set to
operate and the OUTSIDE AIR mode is set. If you push the “FRONT WINDSHIELD” button once again
while in the FRONT WINDSHIELD mode, the mode then
returns to the last mode used.
CAUTION
Do not use the “FRONT WINDSHIELD” button during
cooled air operation in extremely humid weather. The
difference between the temperature of the outside air
and that of
the windshield could cause the outer surface
of the windshield to fog up blocking your vision.
When you turn the ignition switch on after the removal and
installation of the battery terminal, the indicator light may flash
and the operating sound of the motor may be heard. This does
not indicate a malfunction.
You may hear the operating sound of the motor about 70
seconds after the ignition switch is turned off. This does not
indicate a malfunction.

AIR CONDITIONING
256
(d) Replacing the photocatalyst filter for therear seats
This rear air conditioning is equipped with dustproof and
deodorant filter with photocatalyst.
Replace the air filter when the use of rear air conditioning or air
purification function reduces air flow or deodorant
performance.
This filter is an interchangeable type. Do not clean the filter by
washing or air blowing. The use of filter after washing or
cleaning may cause a malfunction of the system. Be sure to
replace it with a new one.
The filter is located in the trunk.
Replace the filter using the following procedures.
1. Be sure to turn the ignition switch to “LOCK”.
21L210
 1 Air purifier 2Filter cover
2. Open the trunk and remove the filter cover in the trunk.
21L211
 1 Filter case 2Filter
3. Pull out the filter case toward you.
4. Replace the filter.
When you install the filter, face the filter surface (gray)
downward and fit the filter folds properly in the case as shown.
5. Install the filter in the reverse order of removal.
The gray surface in the filter may turn to yellow (yellow spots)
because of ultraviolet rays included in the light, however it is
no problem for use.

AIR CONDITIONING
257
When the ignition switch is turned on, the xenon tube comes
on even if the rear air conditioning or rear fan is not operating.
This
does not indicate a malfunction but is required for the long
use of the photocatalyst.
NOTICE
 Do not look into the xenon tube in the air purifier
through the filter slot and do not expose your skin
directly to the light in the xenon tube also. Although
the xenon tube scarcely issues less than 300nm
ultraviolet rays which are thought harmful for the
human body, some people may have symptoms such
as eye sore, vision trouble, skin inflammation, etc.
 Do not disassemble the air purifier , or it may cause a
malfunction. As some part in the purifier is under
high voltage, you may get an electric shock when you
touch it.
 The filters should be installed properly in position.
The use of rear air conditioning controls with the filter
removed may cause the malfunction of the rear air
conditioning controls.
 Turn on the air conditioning with a filter in position.
The activation without an filter may not only cause a
malfunction of the system but also dirty the interior
by spouting dust.

AUDIO
262
Using your audio system: some basics
This section describes some of the basic features of the Lexus
audio system. Some informat ion may not pertain to your
system.
Your audio system works when the ignition switch is in the
“ACC” or “ON” position.
NOTICE
To prevent the battery from being discharged, do not
leave the audio system on longer than necessary when
the engine is not running.
(a) Turning the system on and off
20L355
Push this knob to turn the audio system on and off. Turn
this knob to adjust the volume.
The system turns on in the last mode used.
20L356
Push the “AM·SAT”, “FM”, “TAPE” or “DISC” to turn on
that mode. The selected mode turns on directly.
Push these buttons if you want to switch from one mode to
another.
If the tape or CD is not set, the cassette player or CD player
does not turn on.
You can turn off the cassette player by ejecting the cassette
tape. If the audio system was previously off, then the entire
audio system will be turned off when you eject the cassette
tape. If another function was previously playing, it will come on
again.

AUDIO
282
CD player operation
(a) Inserting or ejecting CDs
The ignition switch must be in the “ACC” or “ON” position.
Your automatic changer can store up to 6 CDs.
20L150c
Setting a single CD:
1. Push the “LOAD” button briefly.
The green indicators at both ends of the slot start blinking and
“WAIT” appears on the display. After the blinking indicators
stay on and the “WAIT” changes to the “LOAD”, the CD door
opens.
2. Insert only one CD while the CD door is open.
You can set a CD at the lowest empty CD number.
After insertion, the set CD is automatically loaded.
If the label faces down, the CD cannot be played. In this case,
“ERROR1” and CD number appear on the display. If you need to insert the next CD, repeat the same procedure
to insert another CD.

Setting all the CDs:
1. Push the “LOAD” button until you hear a beep.
The green indicators at both ends of the slot start blinking and
“WAIT” appears on the display. After the blinking indicators
stay on and the “WAIT” changes to the “LOAD”, the CD door
opens.
2. Insert only one CD while the CD door is open.
The CD door closes and “WAIT” appears again.
3. Insert the next CD after the “WAIT” changes to the
“LOAD” and the CD door opens.
4. Repeat this procedure until you insert all the CDs.
To cancel the operation, push the “LOAD” or “DISC” button.
If you do not insert the CDs within 15 seconds after pushing the
“LOAD” button and “LOAD” is displayed, the operation will be
canceled automatically.
NOTICE
Do not insert one CD stacked on top of another one or
feed them in continuously, to prevent CDs from getting
stuck in the player.