2005 LEXUS ES300 battery

I31548
I30369
I30363
E58517
55-40
- HEATER & AIR CONDITIONERCOOLER COMPRESSOR ASSY
2655 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
(f) Using a vise pliers, hold the magnet clutch hub and install
the bolt.
Torque: 18 NVm (184 kgfVcm, 13 ftVlbf)
11. INSPECT MAGNETIC CLUTCH CLEARANCE
(a) Set the dial indicator to the magnet clutch hub.
(b) Connect the battery positive lead to the terminal 3 of mag-
net clutch connector and the negative lead to the earth
wire. Turn on and off the magnet clutch and measure the
clearance.
Standard clearance:
0.35 - 0.60 mm (0.014 - 0.024 in.)
If the measured value is out of the standard range, remove the
magnet clutch hub and adjust it with magnet clutch washers.
NOTICE:
Adjustment shall be performed with 3 or less magnet
clutch washers.
(c) Remove the compressor and magnetic clutch from the
vise.
(d) Install the bolt and bracket.
12. INSTALL COOLER COMPRESSOR BRACKET
(a) Install the earth wire and cooler compressor bracket with
the screw.

0103D-09
- INTRODUCTIONTERMS FOR AUTOMATIC TRANSAXLE REPAIR
MANUAL01-7
7 Author
: Date
:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
GLOSSARY OF SAE AND TOYOTA TERMS
This glossary lists all SAE-J1930 terms and abbreviations used in this manual in compliance with SAE rec-
ommendations, as well as their Toyota equivalents.
SAE
ABBREVIATIONSSAE TERMSTOYOTA TERMS
( )--ABBREVIATIONS
A/CAir ConditioningAir Conditioner
ACLAir CleanerAir Cleaner
AIRSecondary Air InjectionAir Injection (AI)
APAccelerator Pedal-
B+Battery Positive Voltage+B, Battery Voltage
BAROBarometric Pressure-
CACCharge Air CoolerInter cooler
CARBCarburetorCarburetor
CFIContinuous Fuel Injection-
CKPCrankshaft PositionCrank Angle
CLClosed LoopClosed Loop
CMPCamshaft positionCam Angle
CPPClutch Pedal Position-
CTOXContinuous Trap Oxidizer-
CTPClosed Throttle Potion-
DFIDirect Fuel Injection (Diesel)Direct Injection (DI)
DIDistributor Ignition-
DLC1
DLC2
DLC3Data Link Connector 1
Data Link Connector 2
Data Link Connector 31: Check Connector
2: Total Diagnosis Communication Link (TDCL)
3: OBD II Diagnostic Connector
DTCDiagnostic Trouble CodeDiagnostic Code
DTMDiagnostic Test Mode-
ECLEngine Control Level-
ECMEngine Control ModuleEngine ECU (Electronic Control Unit)
ECTEngine Control TemperatureCoolant Temperature, Water Temperature (THW)
EEPROMElectrically Erasable Programmable Read Only
memoryElectrically Erasable Programmable Read Only memory
(EEPROM),
Erasable Programmable Read Only memory (EPROM)
EFEEarly Fuel EvaporationCold Mixture Heater (CMH), Heat Control Valve (HCV)
EGRExhaust Gas RecirculationExhaust Gas Recirculation (EGR)
EIElectronic IgnitionDistributorless Ignition (DI)
EMEngine ModificationEngine Modification (EM)
EPROMErasable Programmable Read Only MemoryProgrammable Read Only Memory (PROM)
EVAPEvaporative EmissionEvaporative Emission Control (EVAP)
FCFan Control-
FEEPROMFlash Electrically Erasable Programmable
Read Only Memory-
FEPROMFlash Erasable Programmable Read Only Memory-
FFFlexible Fuel-
FPFuel PumpFuel Pump
GENGeneratorAlternator
GNDGroundGround (GND)
HO2SHeated Oxygen SensorHeated Oxygen Sensor (HO2S)
IACIdol Air ControlIdol Speed Control (ISC)
IATIntake Air TemperatureIntake or Inlet Air Temperature
ICMIgnition Control Module-
IFIIndirect Fuel InjectionIndirect Injection
IFSInertia Fuel-Shutoff-

4010O-05
D30614
D25415
C99458
- AUTOMATIC TRANSMISSION / TRANSPARK/NEUTRAL POSITION SWITCH ASSY (U151E)
40-3
2518 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
PARK/NEUTRAL POSITION SWITCH ASSY (U151E)
REPLACEMENT
1. REMOVE BATTERY
2. REMOVE AIR CLEANER ASSY
3. REMOVE AIR CLEANER HOSE NO.1
4. REMOVE AIR CLEANER BRACKET
5. REMOVE AIR CLEANER INLET NO.1
6. REMOVE INTAKE AIR RESONATOR SUB-ASSY
7. REMOVE ENGINE UNDER COVER NO.1
8. DISCONNECT TRANSMISSION CONTROL CABLE
ASSY
(a) Remove the nut from the control shaft lever.
(b) Disconnect the control cable from the control shaft lever.
(c) Remove the clip and disconnect the control cable from
the control cable bracket.
9. REMOVE PARK/NEUTRAL POSITION SWITCH ASSY
(a) Disconnect the park/neutral position switch connector.
(b) Remove the nut, washer and control shaft lever.

40-6
- AUTOMATIC TRANSMISSION / TRANSPARK/NEUTRAL POSITION SWITCH ASSY (U151E)
2521 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
12. ADJUST SHIFT LEVER POSITION (SEE PAGE 40-40)
13. INSPECT SHIFT LEVER POSITION (SEE PAGE 40-40)
14. INSPECT PARK/NEUTRAL POSITION SWITCH ASSY (SEE PAGE 40-7)
15. INSTALL ENGINE UNDER COVER NO.1
16. INSTALL INTAKE AIR RESONATOR SUB-ASSY
17. INSTALL AIR CLEANER INLET NO.1
18. INSTALL AIR CLEANER BRACKET
19. INSTALL AIR CLEANER HOSE NO.1
20. INSTALL AIR CLEANER ASSY
21. INSTALL BATTERY

40060-08
C90569
C90570
C90570
C90569
- AUTOMATIC TRANSMISSION / TRANSSPEED SENSOR
40-19
2534 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
SPEED SENSOR
REPLACEMENT
1. REMOVE BATTERY
2. REMOVE AIR CLEANER ASSY
3. REMOVE AIR CLEANER HOSE NO.1
4. REMOVE SPEED SENSOR (NT SENSOR)
(a) Disconnect the speed sensor connector.
(b) Remove the bolt and speed sensor.
5. REMOVE SPEED SENSOR (NC SENSOR)
(a) Disconnect the speed sensor connector.
(b) Remove the bolt and speed sensor.
6. INSTALL SPEED SENSOR (NC SENSOR)
(a) Coat O-ring with ATF.
(b) Install the speed sensor with the bolt.
Torque: 11.3 NVm (115 kgfVcm, 8 ftVlbf)
HINT:
Make sure of the manufacturer's name.
(c) Connect the speed sensor connector.
7. INSTALL SPEED SENSOR (NT SENSOR)
(a) Coat O-ring with ATF.
(b) Install the speed sensor with the bolt.
Torque: 11.3 NVm (115 kgfVcm, 8 ftVlbf)
HINT:
Make sure of the manufacturer's name.
(c) Connect the speed sensor connector.

40-20
- AUTOMATIC TRANSMISSION / TRANSSPEED SENSOR
2535 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
8. INSTALL AIR CLEANER HOSE NO.1
9. INSTALL AIR CLEANER ASSY
Torque: 5.0 NVm (51 kgfVcm, 44 in.Vlbf)
10. INSTALL BATTERY

C93323
Lock Key
C92370
C93015
C93325
- AUTOMATIC TRANSMISSION / TRANSFLOOR SHIFT ASSY
40-39
2554 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
40. INSTALL FLOOR SHIFT PARKING LOCK CABLE
ASSY
(a) Using a screwdriver, unlock the claw of the lock key of au-
tomatic adjustment part.
(b) Insert the slide cap into the through hole and install.
(c) Shift the shift lever to P position and turn the ignition
switch to Lock.
(d) Insert the lever pin into the hole of the parking lock cable.
(e) Lock the lock key.
41. INSTALL BATTERY
42. ADJUST SHIFT LEVER POSITION(SEE PAGE 40-40)
43. INSPECT SHIFT LEVER POSITION(SEE PAGE 40-40)
44. INSPECT CHECK KEY INTERLOCK OPERATION(SEE PAGE 40-31)
45. INSPECT CHECK SHIFT LOCK OPERATION(SEE PAGE 40-31)
46. INSPECT CHECK SHIFT LOCK RELEASE BUTTON OPERATION(SEE PAGE 40-31)
47. INSTALL CONSOLE BOX DUCT NO.1(SEE PAGE 55-17)
48. INSTALL AIR DUCT REAR NO.2(SEE PAGE 55-17)
49. INSTALL AIR DUCT REAR NO.1(SEE PAGE 55-17)

400FW-02
D25414
D25415
C93327
40-44
- AUTOMATIC TRANSMISSION / TRANSTRANSMISSION CONTROL CABLE ASSY
2559 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
TRANSMISSION CONTROL CABLE ASSY
REPLACEMENT
1. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSY (SEE PAGE 71-1 1)
2. REMOVE AIR CONDITIONING RADIATOR ASSY (SEE PAGE 55-17)
3. REMOVE AIR BAG SENSOR ASSY CENTER (SEE PAGE60-55)
4. REMOVE BATTERY
5. REMOVE AIR CLEANER ASSY
6. REMOVE AIR CLEANER HOSE NO.1
7. REMOVE INTAKE AIR RESONATOR SUB-ASSY
8. REMOVE TRANSMISSION CONTROL CABLE ASSY
(a) Remove the nut from the control shaft lever.
(b) Disconnect the control cable from the control shaft lever.
(c) Remove the clip and disconnect the control cable from
the control cable bracket.
(d) Disconnect the control cable from the control cable
clamp.