2005 KIA Rio lock

Maintenance7-42
1. Remove the headlight bulb cover by turning it
counterclockwise.
2. Disconnect the electrical connector from the bulb
assembly.
3. Unsnap the headlight bulb retaining wire by
depressing the end of it and pulling it upward.
4. Remove the bulb.
5. Install a new bulb by aligning the bulb with the
three(3) slots on the headlight assembly and snap the
headlight bulb retaining wire into position.
6. Connect the headlight bulb electrical connector.
7. Install the headlight bulb cover.
Bulb ReplacementHeadlight Bulb Replacement
WARNING - Halogen Bulbs
 Wear eye protection when changing a bulb.
Allow the bulb to cool before handling it.
 Halogen bulbs contain pressurized gas. If
broken, a halogen bulb will explode and will
produce flying pieces of glass.
 Always handle halogen bulbs carefully to
avoid scratches and abrasion. If the bulbs
are lit, avoid contact with liquids. Never
touch the glass with bare hands. Residual oil
may cause the bulb to overheat and burst
when lit. A bulb should be operated only
when installed in the headlight assembly.
 If a bulb becomes damaged or cracked,
replace it immediately and carefully dispose
it.
1B3106004B
RIO ENG CNA 7-2.qxd 7/29/05 5:18 PM Page 42

7-43 Front Turn Signal / Parking Light Bulb Replacement
1. Turn the parking light bulb socket counterclockwise
and remove it from the headlight assembly.
2. Remove the bulb from the socket by pulling it out.
3. Insert a new bulb in the socket.
4. Re-install the parking light bulb socket into the
headlight assembly and rotate it clockwise to lock
the socket in place.
1B3106006
Rear Combination Light Bulb Replacement1. Using a cross-tip screwdriver, remove the screws
and bolts attaching the rear combination light
assembly to the body.
2. Carefully remove the light assembly from the
vehicle.
1B3106007A
RIO ENG CNA 7-2.qxd 7/29/05 5:18 PM Page 43

5. Insert a new bulb in the socket, then push the bulb
in and rotate it one-quarter turn clockwise to lock
the bulb in place.
6. Re-install the bulb socket into the rear combination
light assembly and rotate it one-quarter turn
clockwise to lock the socket in place.
7. Carefully re-install the light assembly in the
vehicle.
Maintenance7-44
AS2B07033
3. Turn the bulb socket counterclockwise and remove
it from the housing.
4. Push the bulb in, then rotate it one-quarter turn
counterclockwise and remove the bulb from the
socket.
1B3106007C
Turn signal bulbStop/tail light bulb
Backup light bulb
RIO ENG CNA 7-2.qxd 7/29/05 5:18 PM Page 44

Index
9-1
A
ir Bag - Supplemental Restraint System.....................3-46
Air Cleaner ......................................................................7-27
Automatic Transaxle................................................4-9, 7-23
Battery ............................................................................7-31
Before Driving ..................................................................5-4
Brake System ..................................................................4-15
Brakes and Clutch ...........................................................7-20
Bulb Replacement ...........................................................7-42C
limate Control System ................................................4-44
Connection Jumper Cables ...............................................6-5
Cup Holders and Console Storage Compartment ...........3-66
D
aytime Running Lights(DRL) .....................................4-35
Door Locks........................................................................3-5
Electrical Circuit Protection ............................................6-7
Emergency Starting ...........................................................6-4Emission Control System..................................................5-3
Engine Compartment ......................................................7-13
Engine Cooling System ..................................................7-16
Engine Oil and Oil Filter ................................................7-14
Exterior Care ...................................................................7-49
Fuel Filler Door .............................................................3-59
Fuel Requirements ............................................................5-2G
auges ...........................................................................4-25
H
ood ..............................................................................3-57
How To Use This Manual .................................................1-2
If You Have a Flat Tire ..................................................6-16
Ignition Switch ..................................................................4-2
Instrument Cluster...........................................................4-23
Instrument Panel Overview ..............................................2-4
Interior and Exterior Overview .........................................2-2
9
RIO ENG CNA 9.qxd 7/29/05 5:19 PM Page 9-1