2005 KIA Rio heating

Knowing Your Vehicle3-16Heating the Front Seats (If Equipped)
The front seats are electrically heated when the
corresponding switch(shown above) is depressed and
the vehicle ignition is ON. A thermostat regulates seat
temperature when the switch is depressed. To
deactivate the front seats heating system, depress the
switch again.
2FDB301/2FDB304
Type A
Driver’s seatType B
Driver’s seatPassenger’s seat
✽ ✽
NOTICE When cleaning the seats, do not use an organic
solvent such as thinner, benzene, alcohol and
gasoline. Doing so may damage the surface of
the heater or seats.
 To prevent overheating the seat warmer, do not
place blankets, cushions or seat covers on the
seats while the seat warmer is in operation.
 Do not place heavy or sharp objects on seats
equipped with seat warmers. Damage to the
seat warming components could occur.
RIO ENG CNA 3.qxd 7/29/05 5:13 PM Page 16

3-17
Rear Seat
WARNING - Rear Seatback
 The rear seatback must be securely latched.
If not passengers and objects could be
thrown forward and suffer serious injury or
death in the event of a sudden stop or colli-
sion.
 Luggage and other cargo should be laid flat
in the cargo area. If objects are large, heavy
or must be piled, they must be secured.
Under no circumstances should cargo be
piled higher than the seatbacks. Failure to
follow what warnings could result in serious
injury or death in the event of a sudden
stop, collision or rollover.
(Continued)
WARNING
Passengers should use extreme caution when
using seat warmers due to the possibility of
excess heating or burns. In particular, the fol-
lowing types of passengers should exercise
extreme care:
1. Infants, children, elderly or handicapped
persons, or hospital outpatients
2. Persons with sensitive skin or those that
burn easily
3. Fatigued individuals
4. Intoxicated individuals
5. Individuals taking medication that can cause
drowsiness or sleepiness (sleeping pills, cold
tablets, etc.)
RIO ENG CNA 3.qxd 7/29/05 5:13 PM Page 17

Driving Your Vehicle4-26 Fuel GaugeThe fuel gauge indicates the approximate amount of
fuel remaining in the fuel tank.
Fuel tank capacity: 45 L (11.7 US gal.)
The fuel gauge is supplemented by a low fuel warning
light located in the instrument panel.
This gauge is designed to continue indicating the
amount of fuel remaining in the fuel tank even after the
ignition switch has been turned to OFF.
Engine Temperature GaugeThis gauge shows the temperature of the engine
coolant when the ignition switch is ON.
If the gauge pointer moves beyond the normal range
area toward the H position, it indicates overheating that
may damage the engine.
Do not continue driving with an overheated engine.
If your vehicle overheats, refer to “Overheating’’ in the
Index.
1B3105005
1B3105006
With Tachometer
Without Tachometer
With Tachometer
Without Tachometer
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 26

4-29
If the warning light illuminates while driving:
1. Drive to the nearest safe location and carefully stop
your vehicle.
2. With the engine OFF, check the generator drive belt
for looseness or breakage.
3. If the belt is adjusted properly, a problem exists
somewhere in the electrical charging system. Have
an Authorized Kia Dealer locate and correct the
problem as soon as possible.Engine Oil Pressure Warning This warning light indicates the engine oil pressure is
low.
If the warning light comes ON while driving:
1. Drive safely to the side of the road and stop.
2. With the engine OFF, check the engine oil level. If
the level is low, add oil as required.
If the warning light remains ON after adding oil or if
oil is not available, call an Authorized Kia Dealer.Low Fuel Level Warning This warning light indicates the fuel tank is near
empty. The warning light will come on when the fuel
level has dropped to about 9 liters (2.4 US gal.).
Refuel as soon as possible.
✽
NOTICE
Do not drive the vehicle with a loose or broken
generator belt; the engine could be damaged by
overheating because this belt also drives the water
pump.
✽
NOTICE
 If the engine is not stopped as soon as possible,
severe engine damage could result.
 Do not drive the vehicle when the Engine Oil
Pressure Warning Light is ON.
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 29

4-31 Flashing ON and OFF :
If the CHECK ENGINE light begins to flash ON and
OFF, a more serious problem with the ECS or exhaust
system component has been detected. If this happens,
and there is no degradation to performance, the vehicle
is still driveable (avoid high speeds) but should be
checked by an authorized Kia dealer at your earliest
possible convenience. If the flashing CHECK
ENGINE light is accompanied by a decrease in power
or poor running conditions, safely stop the vehicle and
immediately contact Kia Roadside Assistance.
Note that the CHECK ENGINE light will illuminate
for a problem like a loose or missing gas cap, but will
not illuminate as a result of low engine oil or coolant,
low automatic transaxle fluid or engine overheating.
The driver will be alerted to these conditions by other
indicators on the instrument panel.
CAUTION
 Prolonged driving with the On Board
Diagnostic System Malfunction Indicator Light
()illuminated may cause damage to the
emission control systems which could effect
driveability and/or fuel economy.
 If the On Board Diagnostic System
Malfunction Indicator Light () begins to
flash ON and OFF, potential catalytic convert-
er damage is possible which could result in
loss of engine power. Have the On Board
Diagnostic System inspected as soon as possi-
ble by an authorized Kia dealer.
CHECK
CHECK
CHECK
CHECK
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 31

4-41 Cigarette Lighter
To operate the cigarette lighter, press it in and release
it. When it is heated, it automatically pops out ready
for use. If the engine is not running, the ignition switch
must be in the ACC position for the lighter to operate.
1S2107021
✽
NOTICE
 Do not hold the lighter in because it will over-
heat.
 Only a genuine Kia lighter should be used in
the cigarette lighter socket. The use of plug-in
accessories (shavers, hand-held vacuums and
coffee pots, for example) may damage the
socket or cause electrical failure.
 If the lighter does not pop out within
30 seconds, remove it to prevent overheating.
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 41

Driving Your Vehicle4-46Face - floor position
Air flow is directed towards the face and the
floor. The air to the floor is warmer than the
air to the face (except when the temperature
control is set to the extreme cold position).
(outlet port: , , )
Floor position
Most of the air flow is directed to the floor,
with a small amount of the air being directed
to the windshield and side window defroster.
(outlet port: , )
Floor - defrost position
Most of the air flow is directed to the floor
and the windshield with a small amount
directed to the side window defrosters.
(outlet port: , , )
Defrost position
Most of the air flow is directed to the wind-
shield with a small amount of air directed to
the side window defrosters.
(outlet port: , )Air Flow Control Button
It is recommended that under normal conditions the
outside (fresh) air position be selected.
Recirculated air position If you press the air intake control button once (recircu-
late), almost all outside air flow into the vehicle is shut
off, and air within the vehicle will be recirculated.
This position can be used temporarily for maximum
heating or cooling (if equipped with an air condition-
ing) and to help prevent undesirable outside air flow
into the vehicle.
BC
C
D
D
A
C
D
A
D
CAUTION
Continued climate control system operation in the
recirculated air position may allow humidity to
increase inside the vehicle which may fog the
glass and obscure visibility
WARNING
Don’t sleep in a vehicle with air conditioning
system or heating system on. It may cause seri-
ous harm or death to passengers due to a drop
in the oxygen level and/or body temperature.
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 46

Driving Your Vehicle4-48 System OperationVentilation
1. Set the mode selection knob to the position.
2. Set the air intake control switch to the outside air
position (switch indicator OFF).
3. Set the temperature control knob to the desired
position.
4. Set the fan speed control knob to the desired speed.
Heating
1. Set the mode selection knob to the position.
2. Set the air intake control switch to the outside
(fresh) air position.
3. Set the temperature control knob to the desired
position.
4. Set the fan speed control knob to the desired speed.
5. If dehumidified heating is desired, turn the air con-
ditioning system (if equipped) ON.
If cool air is desired at face level for bi-level opera-
tion, set the mode selection knob to the posi-
tion.
If the windshield fogs up, set the mode selection
knob to the position.
CAUTION
Continued climate control system operation in the
recirculated air position may allow humidity to
increase inside the vehicle which may fog the
glass and obscure visibility.
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 48