2005 JAGUAR S TYPE suspension

2DATE OF ISSUE: May 2004
Table of Contents: FiguresJaguar S-TYPE 2005
FIGURES
Fig. Description Variant
01 Power Distribution
Fig. 01.1 . . . . Main Power Distribution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . All Vehicles
Fig. 01.2 . . . . Battery Power Distribution: Part 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . All Vehi cles
Fig. 01.3 . . . . Battery Power Distribution: Part 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . All Vehi cles
Fig. 01.4 . . . . Ignition Switched Power Distribution: I (Accessory) . . . . . . . . . . . . . . . . . . . . . All Vehicles
Fig. 01.5 . . . . Ignition Switched Power Distribution: II (Run) . . . . . . . . . . . . . . . . . . . . . . . . . . All Vehicles
Fig. 01.6 . . . . Switched System Power Distribution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . All Vehicles
Fig. 01.7 . . . . Engine Management System Switched Power Distribution: Gasoline. . . . . . . . Gasoline Vehicles
Fig. 01.8 . . . . Engine Management System Switched Power Distribution: Diesel 2.7V6 . . . . Diesel 2.7V6
02 Battery; Starter; Generator
Fig. 02.1 . . . . Battery; Starter; Generator: V6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V6 Veh icles
Fig. 02.2 . . . . Battery; Starter; Generator: V8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V8 Veh icles
Fig. 02.3 . . . . Battery; Starter; Generator: Diesel 2.7V6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diesel 2.7V6
03 Engine Management
Fig. 03.1 . . . . Engine Management: V6 – Part 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V6 Vehicles
Fig. 03.2 . . . . Engine Management: V6 – Part 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V6 Vehicles
Fig. 03.3 . . . . Engine Management: V8 N/A – Part 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V8 N/A Vehicles
Fig. 03.4 . . . . Engine Management: V8 N/A – Part 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V8 N/A Vehicles
Fig. 03.5 . . . . Engine Management: V8 SC – Part 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V8 SC Vehicles
Fig. 03.6 . . . . Engine Management: V8 SC – Part 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V8 SC Vehicles
Fig. 03.7 . . . . Engine Management: Diesel 2.7V6 – Part 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . Diesel 2.7V6
Fig. 03.8 . . . . Engine Management: Diesel 2.7V6 – Part 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . Diesel 2.7V6
04 Transmission
Fig. 04.1 . . . . Transmission (Automatic) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Autom atic Vehicles
Fig. 04.2 . . . . Transmission (Manual) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manu al Vehicles
05 Chassis
Fig. 05.1 . . . . Dynamic Stability Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . All Vehicles
Fig. 05.2 . . . . Electronic Parking Brake; Variable Assist Power Steering . . . . . . . . . . . . . . . . All Vehicles
Fig. 05.3 . . . . Adaptive Speed Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adap tive Speed Control Vehicles
Fig. 05.4 . . . . Suspension Adaptive Damping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adaptive D amping Vehicles
Fig. 05.5 . . . . Tire Pressure Monitoring System: NAS V8 SC . . . . . . . . . . . . . . . . . . . . . . . . . NAS V8 SC Vehicles
06 Climate Control
Fig. 06.1 . . . . Climate Control System; Windshield Heaters . . . . . . . . . . . . . . . . . . . . . . . . . . All Vehicles
07 Instrumentation
Fig. 07.1 . . . . Instrument Cluster; Audible Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . All Vehicles
08 Exterior Lighting
Fig. 08.1 . . . . Exterior Lighting: Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N on HID Headlamp Vehicles
Fig. 08.2 . . . . Exterior Lighting: Front – HID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HID He adlamp Vehicles
Fig. 08.3 . . . . Exterior Lighting: Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A ll Vehicles
Fig. 08.4 . . . . Exterior Lighting: Rear – Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trailer Towi ng Vehicles
Fig. 08.5 . . . . Headlamp Leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . He adlamp Leveling Vehicles
09 Interior Lighting
Fig. 09.1 . . . . Interior Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . All Vehicles
Fig. 09.2 . . . . Dimmer-Controlled Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . All Ve hicles

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 03.1
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAPP SENSOR CA88 6-WAY / BLACK TOP OF ACCELERATOR PEDAL
BRAKE ON / OFF SWITCH CA37 2-WAY / GREEN TOP OF BRAKE PEDAL
CKP SENSOR PI55 2-WAY / BLACK ENGINE TIMING COVER, CRANKSHAFT PULLEY
CMP SENSOR 1 PI57 2-WAY / BLACK BANK 1 (RH) CAMSHAFT COVER, FRONT
CMP SENSOR 2 PI56 2-WAY / BLACK BANK 2 (LH) CAMSHAFT COVER, FRONT
ECT SENSOR PI25 2-WAY / BLACK ENGINE VEE, COOLANT OUTLET CASTING
EFT SENSOR IL9 2-WAY / BLACK FUEL RAIL, FRONT
ENGINE CONTROL MODULE PI1 134-WAY / BLACK FRONT BULKHEAD, P ASSENGER SIDE
EOT SENSOR PI24 2-WAY / BLACK ADJACENT TO OIL FILTER
EVAP CANISTER CLOSE VALVE CA270 2-WAY / BLACK ABOVE REAR AXLE (FUEL TANK COMPONENTS)
EVAP CANISTER PURGE VALVE FH111 2-WAY / BLACK ENGINE COMPARTMENT, LH SIDE, ADJACENT TO SUSPENSION TURRET
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
FTP SENSOR FP1 3-WAY / BLACK FUEL TANK PIPING, LH SIDE (UNDER ACCESS PLATE)
HO2 SENSOR DOWNSTREAM 1/2 PI11 4-WAY / BLACK RH EXHAUST, CATALYST CENTER
HO2 SENSOR DOWNSTREAM 2/2 PI13 4-WAY / BLACK LH EXHAUST, CATALYST CENTER
HO2 SENSOR UPSTREAM 1/1 PI10 4-WAY / BLACK RH EXHAUST, TOP OF CATALYST
HO2 SENSOR UPSTREAM 2/1 PI12 4-WAY / BLACK LH EXHAUST, TOP OF CATALYST
IMT SOLENOID VALVE 1 PI30 2-WAY / BLACK INTAKE MANIFOLD, REAR
IMT SOLENOID VALVE 2 PI31 2-WAY / BLACK INTAKE MANIFOLD, REAR
IP SENSOR IL12 3-WAY / BLACK FUEL RAIL, REAR
KNOCK SENSOR 1 PI20 2-WAY / BLACK ENGINE VEE, TOWARD FRONT, BANK 2 (FRONT SENSOR)
KNOCK SENSOR 2 PI19 2-WAY / BLACK ENGINE BLOCK, REAR, BANK 1 (REAR SENSOR)
MAF SENSOR PI14 5-WAY / BLACK ENGINE AIR INTAKE, ADJACENT TO AIR CLEANER
MAP SENSOR PI29 4-WAY / BLACK INTAKE MANIFOLD, UPPER REAR
THROTTLE MOTOR PI18 2-WAY / BLACK ENGINE AIR INTAKE, FRONT
THROTTLE MOTOR RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R5
TP SENSOR PI26 4-WAY / BLACK THROTTLE BODY, THROTTLE SHAFT
VVT SOLENOID VALVE 1 PI16 2-WAY / BLACK RH CYLINDER HEAD, FRONT
VVT SOLENOID VALVE 2 PI17 2-WAY / BLACK LH CYLINDER HEAD, FRONTHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFC12 14-WAY / GREY / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, PASSENGER SIDE
FC26 16-WAY / BLUE / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, DRIVER SIDE
FH1 20-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH3 16-WAY / BLUE / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST
FP2 8-WAY / BLACK / CABIN HARNESS TO FUEL PUMP HARNESS TOP OF FUEL TANK, RH SIDE
IL10 12-WAY / BLACK / ENGINE HARNESS TO FUEL INJECTOR LINK REAR OF ENGINE
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationPI40 (LHD) ENGINE COMPARTMENT, BEHIND RH WHEEL ARCH LINER
PI40 (RHD) ENGINE COMPARTMENT, BEHIND LH WHEEL ARCH LINER
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Engine Control Module Pin Description and CharacteristicO PI1–1 HO2 SENSOR HEATER CONTROL – 1/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
O PI1–2 HO2 SENSOR HEATER CONTROL – 1/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
PG PI1–4 POWER GROUND 1: GROUND
PG PI1–5 POWER GROUND 2: GROUND
I PI1–6 ENGINE CRANK: B+
I PI1–7 IGNITION ON: B+
I PI1–8 BRAKE ON / OFF SWITCH: NORMALLY OPEN / B+ WHEN ACTIVATED
I PI1–10 INERTIA SWITCH: NORMALLY CLOSED / OPEN CIRCUIT WHEN ACTIVATED
SS PI1–12 SENSOR POWER SUPPLY 1: NOMINAL 5 V
SS PI1–13 SENSOR POWER SUPPLY 2: NOMINAL 5 V
SG PI1–17 SMALL SIGNAL GROUND 1: GROUND
SG PI1–18 SMALL SIGNAL GROUND 2: GROUND
SG PI1–19 SENSOR GROUND 1: GROUND
SG PI1–20 SENSOR GROUND 2: GROUND
B+ PI1–22 BATTERY POWER SUPPLY: B+
B+ PI1–23 EMS SWITCHED POWER SUPPLY 1: B+
B+ PI1–24 EMS SWITCHED POWER SUPPLY 2: B+
SG PI1–29 HO2 SENSOR HEATER GROUND – 1/1: GROUND
SG PI1–30 HO2 SENSOR HEATER GROUND – 1/1: GROUND
I PI1–31 AUTOMATIC – PARK / NEUTRAL SIGNAL: B+ WHEN ACTIVATED MANUAL, ROW – PARK / NEUTRAL SIGNAL: B+ WHEN IGNITION CRANK (III)
MANUAL, NAS – CLUTCH PEDAL SAFETY SWITCH (PARK / NEUTRAL SIGNAL): B+ WHEN ACTIVATED
I PI1–36 CRANKSHAFT SENSOR SIGNAL: PULSED SIGNAL, 70 PULSES PER ENGINE CYCLE
SG PI1–37 CRANKSHAFT SENSOR SIGNAL GROUND: GROUND
O PI1–38 INTAKE MANIFOLD TUNING VALVE SOLENOID DRIVE – 1 / TOP: GROUND WHEN ACTIVATED
O PI1–39 INTAKE MANIFOLD TUNING VALVE SOLENOID DRIVE – 2 / BOTTOM: GROUND WHEN ACTIVATED
O PI1–40 EMS CONTROL RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–41 STARTER RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
SG PI1–43 TP AND APP SIGNALS SHIELD: GROUND
I PI1–44 MASS AIR FLOW SENSOR SIGNAL: NOMINAL 0 – 5 V BY ENGINE OPERATING CONDITION
SG PI1–45 MASS AIR FLOW SENSOR GROUND: GROUND
SG PI1–46 MASS AIR FLOW SENSOR GROUND: GROUND
I PI1–50 ENGINE FUEL TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
O PI1–52 THROTTLE MOTOR RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–53 GENERATOR CONTROL: VARIABLE VOLTAGE
SG PI1–54 THROTTLE MOTOR GROUND: GROUND
O PI1–55 HO2 SENSOR HEATER CONTROL – 2/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
O PI1–56 HO2 SENSOR HEATER CONTROL – 2/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
I PI1–65 GENERATOR FIELD RETURN SIGNAL: VARIABLE VOLTAGE BY GENERATOR OPERATING CONDITION
O PI1–66 EVAP CANISTER PURGE VALVE DRIVE: PWM, 10 Hz, POSITIVE DUTY CYCLE RANGE 7% – 100%
O PI1–67 EVAP CANISTER CLOSE VALVE DRIVE: TO CLOSE, ECM SWITCHES CIRCUIT TO GROUND
I PI1–68 BANK 2 CAMSHAFT SENSOR SIGNAL: PULSED SIGNAL, 4 PULSES PER ENGINE CYCLE
SG PI1–69 BANK 2 CAMSHAFT SENSOR GROUND: GROUND
I PI1–70 ENGINE COOLANT TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–71 INTAKE AIR TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–73 INJECTION PRESSURE SENSOR SIGNAL, NOMINAL 0 – 5 V: POTENTIOMETER – VOLTAGE INCREASES AS PRESSURE INCREASES
I PI1–75 THROTTLE POSITION SENSOR 1 SIGNAL: IDLE = 0.60 V; FULL THROTTLE = 4.30 V
I PI1–76 THROTTLE POSITION SENSOR 2 SIGNAL: IDLE = 1.48 V; FULL THROTTLE = 4.40 V
I PI1–78 ENGINE OIL TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–79 GENERATOR FAULT; CHARGE WARNING
O PI1–80 THROTTLE MOTOR DRIVE: B+ TO ACTIVATE MOTOR
SG PI1–81 HO2 SENSOR HEATER GROUND – 2/1: GROUND
SG PI1–82 HO2 SENSOR HEATER GROUND – 2/1: GROUND
I PI1–83 HO2 SENSOR 1/1 SIGNAL: VARIABLE CURRENT
I PI1–84 HO2 SENSOR 1/1 SIGNAL: CONSTANT CURRENT
SG PI1–91 HO2 SENSOR HEATERS 1/2, 2/2 GROUND: GROUND
O PI1–92 HO2 SENSOR HEATER CONTROL – 1/2: PWM, 1 CYCLE PER 256 mS, POSITIVE DUTY CYCLE RANGE 0 mS = 0%, 77 mS = 30%, 256 mS = 100%
O PI1–93 HO2 SENSOR HEATER CONTROL – 2/2: PWM, 1 CYCLE PER 256 mS, POSITIVE DUTY CYCLE RANGE 0 mS = 0%, 77 mS = 30%, 256 mS = 100%
I PI1–94 BANK 1 CAMSHAFT SENSOR SIGNAL: PULSED SIGNAL, 4 PULSES PER ENGINE CYCLE
SG PI1–95 BANK 1 CAMSHAFT SENSOR GROUND: GROUND
I PI1–98 BANK 1 KNOCK SENSOR SIGNAL: VARIABLE VOLTAGE DEPENDENT ON ENGINE VIBRATION
I PI1–99 BANK 2 KNOCK SENSOR SIGNAL: VARIABLE VOLTAGE DEPENDENT ON ENGINE VIBRATION
SG PI1–100 SENSOR SHIELD: GROUND
I PI1–102 ACCELERATOR PEDAL POSITION SENSOR 1 SIGNAL: FOOT OFF = 0.75 V; FULLY DEPRESSED = 3.40 V (AUTO) 3.20 V (MAN)
I PI1–103 ACCELERATOR PEDAL POSITION SENSOR 2 SIGNAL: FOOT OFF = 3.38 V; FULLY DEPRESSED = 2.05 V (AUTO) 2.14 V (MAN)
I PI1–104 FUEL TANK PRESSURE SENSOR SIGNAL, NOMINAL 0 – 5 V: VOLTAGE INCREASES AS PRESSURE INCREASES
D PI1–105 SERIAL DATA LINK: SERIAL COMMUNICATION
O PI1–106 THROTTLE MOTOR DRIVE: B+ TO ACTIVATE MOTOR
I PI1–107 HO2 SENSOR 2/1 SIGNAL: VARIABLE CURRENT
I PI1–108 HO2 SENSOR 2/1 SIGNAL: CONSTANT CURRENT
O PI1–109 BANK 1 VVT SOLENOID VALVE: PWM, 300 Hz, POSITIVE DUTY CYCLE RANGE 0% – 100%
O PI1–110 BANK 2 VVT SOLENOID VALVE: PWM, 300 Hz, POSITIVE DUTY CYCLE RANGE 0% – 100%
SG PI1–111 FUEL INJECTORS 2, 3, 5, 8 GROUND: GROUND
SG PI1–116 FUEL INJECTORS 1, 4, 6, 7 GROUND: GROUND
C PI1–123 CAN –
C PI1–124 CAN +
I PI1–127 MAP SENSOR SIGNAL, NOMINAL 0 – 5 V: VOLTAGE INCREASES AS MANIFOLD ABSOLUTE PRESSURE INCREASES
I PI1–128 HO2 SENSOR 1/2 SIGNAL, NOMINAL 1 V SWING: 0.1 – 0.9 V SWING
I PI1–129 HO2 SENSOR 2/2 SIGNAL, NOMINAL 1 V SWING: 0.1 – 0.9 V SWING
SG PI1–130 HO2 SENSORS SHIELD: GROUND
B+ PI1–134 THROTTLE MOTOR POWER SUPPLY: B+ WHEN RELAY ACTIVATED

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 03.3
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAPP SENSOR CA88 6-WAY / BLACK TOP OF ACCELERATOR PEDAL
BRAKE ON / OFF SWITCH CA37 2-WAY / GREEN TOP OF BRAKE PEDAL
CKP SENSOR PI21 2-WAY / BLACK ENGINE UNDER SIDE, FORWARD OF BELL HOUSING
CMP SENSOR 1 PI23 2-WAY / BLACK BANK 1 (RH) CAMSHAFT COVER, FRONT
CMP SENSOR 2 PI22 2-WAY / BLACK BANK 2 (LH) CAMSHAFT COVER, FRONT
ECT SENSOR PI25 2-WAY / BLACK ENGINE VEE, COOLANT OUTLET CASTING
EFT SENSOR PI27 2-WAY / BLACK FUEL RAIL, RH REAR
EGR VALVE PI15 6-WAY / BLACK INTAKE MANIFOLD, RH FRONT
ENGINE CONTROL MODULE PI1 134-WAY / BLACK FRONT BULKHEAD, P ASSENGER SIDE
EOT SENSOR PI24 2-WAY / BLACK ADJACENT TO OIL FILTER
EVAP CANISTER CLOSE VALVE CA270 2-WAY / BLACK ABOVE REAR AXLE (FUEL TANK COMPONENTS)
EVAP CANISTER PURGE VALVE FH111 2-WAY / BLACK ENGINE COMPARTMENT, LH SIDE, ADJACENT TO SUSPENSION TURRET
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
FTP SENSOR FP1 3-WAY / BLACK FUEL TANK PIPING, LH SIDE (UNDER ACCESS PLATE)
HO2 SENSOR DOWNSTREAM 1/2 PI11 4-WAY / BLACK RH EXHAUST, TOP OF CATALYST
HO2 SENSOR DOWNSTREAM 2/2 PI13 4-WAY / BLACK LH EXHAUST, TOP OF CATALYST
HO2 SENSOR UPSTREAM 1/1 PI10 4-WAY / BLACK RH EXHAUST, CATALYST CENTER
HO2 SENSOR UPSTREAM 2/1 PI12 4-WAY / BLACK RH EXHAUST, CATALYST CENTER
IP SENSOR PI28 3-WAY / BLACK FUEL RAIL, RH FRONT
KNOCK SENSOR 1 PI20 2-WAY / BLACK ENGINE VEE, BANK 1
KNOCK SENSOR 2 PI19 2-WAY / BLACK ENGINE VEE, BANK 2
MAF SENSOR PI14 5-WAY / BLACK ENGINE AIR INTAKE, ADJACENT TO AIR CLEANER
MAP SENSOR PI29 4-WAY / BLACK INTAKE MANIFOLD, LOWER REAR
THROTTLE MOTOR PI18 2-WAY / BLACK ENGINE AIR INTAKE, FRONT
THROTTLE MOTOR RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R5
TP SENSOR PI26 4-WAY / BLACK THROTTLE BODY, THROTTLE SHAFT
VVT SOLENOID VALVE 1 PI16 2-WAY / BLACK RH CYLINDER HEAD, FRONT
VVT SOLENOID VALVE 2 PI17 2-WAY / BLACK LH CYLINDER HEAD, FRONTHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFC12 14-WAY / GREY / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, PASSENGER SIDE
FC26 16-WAY / BLUE / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, DRIVER SIDE
FH1 20-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH3 16-WAY / BLUE / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST
FP2 8-WAY / BLACK / CABIN HARNESS TO FUEL PUMP HARNESS TOP OF FUEL TANK, RH SIDE
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationPI40 (LHD) ENGINE COMPARTMENT, BEHIND RH WHEEL ARCH LINER
PI40 (RHD) ENGINE COMPARTMENT, BEHIND LH WHEEL ARCH LINER
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Engine Control Module Pin Description and CharacteristicO PI1–1 HO2 SENSOR HEATER CONTROL – 1/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
O PI1–2 HO2 SENSOR HEATER CONTROL – 1/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
PG PI1–4 POWER GROUND 1: GROUND
PG PI1–5 POWER GROUND 2: GROUND
I PI1–6 ENGINE CRANK: B+
I PI1–7 IGNITION ON: B+
I PI1–8 BRAKE ON / OFF SWITCH: NORMALLY OPEN / B+ WHEN ACTIVATED
I PI1–10 INERTIA SWITCH: NORMALLY CLOSED / OPEN CIRCUIT WHEN ACTIVATED
SS PI1–12 SENSOR POWER SUPPLY 1: NOMINAL 5 V
SS PI1–13 SENSOR POWER SUPPLY 2: NOMINAL 5 V
SG PI1–17 SMALL SIGNAL GROUND 1: GROUND
SG PI1–18 SMALL SIGNAL GROUND 2: GROUND
SG PI1–19 SENSOR GROUND 1: GROUND
SG PI1–20 SENSOR GROUND 2: GROUND
B+ PI1–22 BATTERY POWER SUPPLY: B+
B+ PI1–23 EMS SWITCHED POWER SUPPLY 1: B+
B+ PI1–24 EMS SWITCHED POWER SUPPLY 2: B+
SG PI1–29 HO2 SENSOR HEATER GROUND – 1/1: GROUND
SG PI1–30 HO2 SENSOR HEATER GROUND – 1/1: GROUND
I PI1–31 AUTOMATIC – PARK / NEUTRAL SIGNAL: B+ WHEN ACTIVATED MANUAL, ROW – PARK / NEUTRAL SIGNAL: B+ WHEN IGNITION CRANK (III)
MANUAL, NAS – CLUTCH PEDAL SAFETY SWITCH (PARK / NEUTRAL SIGNAL): B+ WHEN ACTIVATED
I PI1–36 CRANKSHAFT SENSOR SIGNAL: PULSED SIGNAL, 70 PULSES PER ENGINE CYCLE
SG PI1–37 CRANKSHAFT SENSOR SIGNAL GROUND: GROUND
O PI1–40 EMS CONTROL RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–41 STARTER RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
SG PI1–43 TP AND APP SIGNALS SHIELD: GROUND
I PI1–44 MASS AIR FLOW SENSOR SIGNAL: NOMINAL 0 – 5 V BY ENGINE OPERATING CONDITION
SG PI1–45 MASS AIR FLOW SENSOR GROUND: GROUND
SG PI1–46 MASS AIR FLOW SENSOR GROUND: GROUND
I PI1–50 ENGINE FUEL TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
O PI1–52 THROTTLE MOTOR RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
SG PI1–54 THROTTLE MOTOR GROUND: GROUND
O PI1–55 HO2 SENSOR HEATER CONTROL – 2/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
O PI1–56 HO2 SENSOR HEATER CONTROL – 2/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
O PI1–57 EGR DRIVE 1: B+; EGR DRIVE 1, 2, 3 AND 4 ARE OPERATED IN TURN
O PI1–58 EGR DRIVE 2: B+; EGR DRIVE 1, 2, 3 AND 4 ARE OPERATED IN TURN
O PI1–59 EGR DRIVE 3: B+; EGR DRIVE 1, 2, 3 AND 4 ARE OPERATED IN TURN
O PI1–60 EGR DRIVE 4: B+; EGR DRIVE 1, 2, 3 AND 4 ARE OPERATED IN TURN
O PI1–66 EVAP CANISTER PURGE VALVE DRIVE: PWM, 10 Hz, POSITIVE DUTY CYCLE RANGE 7% – 100%
O PI1–67 EVAP CANISTER CLOSE VALVE DRIVE: TO CLOSE, ECM SWITCHES CIRCUIT TO GROUND
I PI1–68 BANK 2 CAMSHAFT SENSOR SIGNAL: PULSED SIGNAL, 4 PULSES PER ENGINE CYCLE
SG PI1–69 BANK 2 CAMSHAFT SENSOR GROUND: GROUND
I PI1–70 ENGINE COOLANT TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–71 INTAKE AIR TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–73 INJECTION PRESSURE SENSOR SIGNAL, NOMINAL 0 – 5 V: POTENTIOMETER – VOLTAGE INCREASES AS PRESSURE INCREASES
I PI1–75 THROTTLE POSITION SENSOR 1 SIGNAL: IDLE = 0.60 V; FULL THROTTLE = 4.30 V
I PI1–76 THROTTLE POSITION SENSOR 2 SIGNAL: IDLE = 1.48 V; FULL THROTTLE = 4.40 V
I PI1–78 ENGINE OIL TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–79 GENERATOR FAULT; CHARGE WARNING
O PI1–80 THROTTLE MOTOR DRIVE: B+ TO ACTIVATE MOTOR
SG PI1–81 HO2 SENSOR HEATER GROUND – 2/1: GROUND
SG PI1–82 HO2 SENSOR HEATER GROUND – 2/1: GROUND
I PI1–83 HO2 SENSOR 1/1 SIGNAL: VARIABLE CURRENT
I PI1–84 HO2 SENSOR 1/1 SIGNAL: CONSTANT CURRENT
SG PI1–91 HO2 SENSOR HEATERS 1/2, 2/2 GROUND: GROUND
O PI1–92 HO2 SENSOR HEATER CONTROL – 1/2: PWM, 1 CYCLE PER 256 mS, POSITIVE DUTY CYCLE RANGE 0 mS = 0%, 77 mS = 30%, 256 mS = 100%
O PI1–93 HO2 SENSOR HEATER CONTROL – 2/2: PWM, 1 CYCLE PER 256 mS, POSITIVE DUTY CYCLE RANGE 0 mS = 0%, 77 mS = 30%, 256 mS = 100%
I PI1–94 BANK 1 CAMSHAFT SENSOR SIGNAL: PULSED SIGNAL, 4 PULSES PER ENGINE CYCLE
SG PI1–95 BANK 1 CAMSHAFT SENSOR GROUND: GROUND
I PI1–98 BANK 1 KNOCK SENSOR SIGNAL: VARIABLE VOLTAGE DEPENDENT ON ENGINE VIBRATION
I PI1–99 BANK 2 KNOCK SENSOR SIGNAL: VARIABLE VOLTAGE DEPENDENT ON ENGINE VIBRATION
SG PI1–100 SENSOR SHIELD: GROUND
I PI1–102 ACCELERATOR PEDAL POSITION SENSOR 1 SIGNAL: FOOT OFF = 0.75 V; FULLY DEPRESSED = 3.40 V (AUTO) 3.20 V (MAN)
I PI1–103 ACCELERATOR PEDAL POSITION SENSOR 2 SIGNAL: FOOT OFF = 3.38 V; FULLY DEPRESSED = 2.05 V (AUTO) 2.14 V (MAN)
I PI1–104 FUEL TANK PRESSURE SENSOR SIGNAL, NOMINAL 0 – 5 V: VOLTAGE INCREASES AS PRESSURE INCREASES
D PI1–105 SERIAL DATA LINK: SERIAL COMMUNICATION
O PI1–106 THROTTLE MOTOR DRIVE: B+ TO ACTIVATE MOTOR
I PI1–107 HO2 SENSOR 2/1 SIGNAL: VARIABLE CURRENT
I PI1–108 HO2 SENSOR 2/1 SIGNAL: CONSTANT CURRENT
O PI1–109 BANK 1 VVT SOLENOID VALVE: PWM, 300 Hz, POSITIVE DUTY CYCLE RANGE 0% – 100%
O PI1–110 BANK 2 VVT SOLENOID VALVE: PWM, 300 Hz, POSITIVE DUTY CYCLE RANGE 0% – 100%
SG PI1–111 FUEL INJECTORS 2, 3, 5, 8 GROUND: GROUND
SG PI1–116 FUEL INJECTORS 1, 4, 6, 7 GROUND: GROUND
C PI1–123 CAN –
C PI1–124 CAN +
I PI1–127 MAP SENSOR SIGNAL, NOMINAL 0 – 5 V: VOLTAGE INCREASES AS MANIFOLD ABSOLUTE PRESSURE INCREASES
I PI1–128 HO2 SENSOR 1/2 SIGNAL, NOMINAL 1 V SWING: 0.1 – 0.9 V SWING
I PI1–129 HO2 SENSOR 2/2 SIGNAL, NOMINAL 1 V SWING: 0.1 – 0.9 V SWING
SG PI1–130 HO2 SENSORS SHIELD: GROUND
B+ PI1–134 THROTTLE MOTOR POWER SUPPLY: B+ WHEN RELAY ACTIVATED

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 03.5
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAPP SENSOR CA88 6-WAY / BLACK TOP OF ACCELERATOR PEDAL
BRAKE ON / OFF SWITCH CA37 2-WAY / GREEN TOP OF BRAKE PEDAL
CKP SENSOR PI21 2-WAY / BLACK ENGINE UNDER SIDE, FORWARD OF BELL HOUSING
CMP SENSOR 1 PI23 2-WAY / BLACK BANK 1 (RH) CAMSHAFT COVER, FRONT
CMP SENSOR 2 PI22 2-WAY / BLACK BANK 2 (LH) CAMSHAFT COVER, FRONT
ECT SENSOR PI25 2-WAY / BLACK ENGINE VEE, COOLANT OUTLET CASTING
EFT SENSOR PI27 2-WAY / BLACK FUEL RAIL, RH REAR
EGR VALVE PI15 6-WAY / BLACK INTAKE MANIFOLD, REAR
ENGINE CONTROL MODULE PI1 134-WAY / BLACK FRONT BULKHEAD, P ASSENGER SIDE
EOT SENSOR PI24 2-WAY / BLACK ADJACENT TO OIL FILTER
EVAP CANISTER CLOSE VALVE CA270 2-WAY / BLACK ABOVE REAR AXLE (FUEL TANK COMPONENTS)
EVAP CANISTER PURGE VALVE FH111 2-WAY / BLACK ENGINE COMPARTMENT, LH SIDE, ADJACENT TO SUSPENSION TURRET
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
FTP SENSOR FP1 3-WAY / BLACK FUEL TANK PIPING, LH SIDE (UNDER ACCESS PLATE)
HO2 SENSOR DOWNSTREAM 1/2 PI11 4-WAY / BLACK RH EXHAUST, TOP OF CATALYST
HO2 SENSOR DOWNSTREAM 2/2 PI13 4-WAY / BLACK LH EXHAUST, TOP OF CATALYST
HO2 SENSOR UPSTREAM 1/1 PI10 4-WAY / BLACK RH EXHAUST, CATALYST CENTER
HO2 SENSOR UPSTREAM 2/1 PI12 4-WAY / BLACK RH EXHAUST, CATALYST CENTER
IAT SENSOR 2 PI43 2-WAY / BLACK INTAKE MANIFOLD, RH SIDE, REAR
IP SENSOR PI28 3-WAY / BLACK FUEL RAIL, LH REAR
KNOCK SENSOR 1 PI20 2-WAY / BLACK ENGINE VEE, BANK 1
KNOCK SENSOR 2 PI19 2-WAY / BLACK ENGINE VEE, BANK 2
MAF SENSOR PI14 5-WAY / BLACK ENGINE AIR INTAKE, ADJACENT TO AIR CLEANER
MAP SENSOR PI29 4-WAY / BLACK INTAKE MANIFOLD, REAR, BELOW THROTTLE ASSEMBLY
THROTTLE MOTOR PI18 2-WAY / BLACK ENGINE AIR INTAKE, REAR
THROTTLE MOTOR RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R5
TP SENSOR PI26 4-WAY / BLACK THROTTLE BODY, THROTTLE SHAFTHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFC12 14-WAY / GREY / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, PASSENGER SIDE
FC26 16-WAY / BLUE / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, DRIVER SIDE
FH1 20-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH3 16-WAY / BLUE / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST
FP2 8-WAY / BLACK / CABIN HARNESS TO FUEL PUMP HARNESS TOP OF FUEL TANK, RH SIDE
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationPI40 (LHD) ENGINE COMPARTMENT, BEHIND RH WHEEL ARCH LINER
PI40 (RHD) ENGINE COMPARTMENT, BEHIND LH WHEEL ARCH LINER
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Engine Control Module
Pin Description and CharacteristicO PI1–1 HO2 SENSOR HEATER CONTROL – 1/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
O PI1–2 HO2 SENSOR HEATER CONTROL – 1/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
PG PI1–4 POWER GROUND 1: GROUND
PG PI1–5 POWER GROUND 2: GROUND
I PI1–6 ENGINE CRANK: B+
I PI1–7 IGNITION ON: B+
I PI1–8 BRAKE ON / OFF SWITCH: NORMALLY OPEN / B+ WHEN ACTIVATED
I PI1–10 INERTIA SWITCH: NORMALLY CLOSED / OPEN CIRCUIT WHEN ACTIVATED
SS PI1–12 SENSOR POWER SUPPLY 1: NOMINAL 5 V
SS PI1–13 SENSOR POWER SUPPLY 2: NOMINAL 5 V
SG PI1–17 SMALL SIGNAL GROUND 1: GROUND
SG PI1–18 SMALL SIGNAL GROUND 2: GROUND
SG PI1–19 SENSOR GROUND 1: GROUND
SG PI1–20 SENSOR GROUND 2: GROUND
B+ PI1–22 BATTERY POWER SUPPLY: B+
B+ PI1–23 EMS SWITCHED POWER SUPPLY 1: B+
B+ PI1–24 EMS SWITCHED POWER SUPPLY 2: B+
SG PI1–29 HO2 SENSOR HEATER GROUND – 1/1: GROUND
SG PI1–30 HO2 SENSOR HEATER GROUND – 1/1: GROUND
I PI1–31 AUTOMATIC – PARK / NEUTRAL SIGNAL: B+ WHEN ACTIVATED MANUAL, ROW – PARK / NEUTRAL SIGNAL: B+ WHEN IGNITION CRANK (III)
MANUAL, NAS – CLUTCH PEDAL SAFETY SWITCH (PARK / NEUTRAL SIGNAL): B+ WHEN ACTIVATED
I PI1–36 CRANKSHAFT SENSOR SIGNAL: PULSED SIGNAL, 70 PULSES PER ENGINE CYCLE
SG PI1–37 CRANKSHAFT SENSOR SIGNAL GROUND: GROUND
O PI1–40 EMS CONTROL RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–41 STARTER RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
SG PI1–43 TP AND APP SIGNALS SHIELD: GROUND
I PI1–44 MASS AIR FLOW SENSOR SIGNAL: NOMINAL 0 – 5 V BY ENGINE OPERATING CONDITION
SG PI1–45 MASS AIR FLOW SENSOR GROUND: GROUND
SG PI1–46 MASS AIR FLOW SENSOR GROUND: GROUND
I PI1–50 ENGINE FUEL TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
O PI1–52 THROTTLE MOTOR RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
SG PI1–54 THROTTLE MOTOR GROUND: GROUND
O PI1–55 HO2 SENSOR HEATER CONTROL – 2/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
O PI1–56 HO2 SENSOR HEATER CONTROL – 2/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
O PI1–57 EGR DRIVE 1: B+; EGR DRIVE 1, 2, 3 AND 4 ARE OPERATED IN TURN
O PI1–58 EGR DRIVE 2: B+; EGR DRIVE 1, 2, 3 AND 4 ARE OPERATED IN TURN
O PI1–59 EGR DRIVE 3: B+; EGR DRIVE 1, 2, 3 AND 4 ARE OPERATED IN TURN
O PI1–60 EGR DRIVE 4: B+; EGR DRIVE 1, 2, 3 AND 4 ARE OPERATED IN TURN
O PI1–66 EVAP CANISTER PURGE VALVE DRIVE: PWM, 10 Hz, POSITIVE DUTY CYCLE RANGE 7% – 100%
O PI1–67 EVAP CANISTER CLOSE VALVE DRIVE: TO CLOSE, ECM SWITCHES CIRCUIT TO GROUND
I PI1–68 BANK 2 CAMSHAFT SENSOR SIGNAL: PULSED SIGNAL, 4 PULSES PER ENGINE CYCLE
SG PI1–69 BANK 2 CAMSHAFT SENSOR GROUND: GROUND
I PI1–70 ENGINE COOLANT TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–71 INTAKE AIR TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–72 INTAKE AIR TEMPERATURE SENSOR 2 SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–73 INJECTION PRESSURE SENSOR SIGNAL, NOMINAL 0 – 5 V: POTENTIOMETER – VOLTAGE INCREASES AS PRESSURE INCREASES
I PI1–75 THROTTLE POSITION SENSOR 1 SIGNAL: IDLE = 0.60 V; FULL THROTTLE = 4.30 V
I PI1–76 THROTTLE POSITION SENSOR 2 SIGNAL: IDLE = 1.48 V; FULL THROTTLE = 4.40 V
I PI1–78 ENGINE OIL TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–79 GENERATOR FAULT; CHARGE WARNING
O PI1–80 THROTTLE MOTOR DRIVE: B+ TO ACTIVATE MOTOR
SG PI1–81 HO2 SENSOR HEATER GROUND – 2/1: GROUND
SG PI1–82 HO2 SENSOR HEATER GROUND – 2/1: GROUND
I PI1–83 HO2 SENSOR 1/1 SIGNAL: VARIABLE CURRENT
I PI1–84 HO2 SENSOR 1/1 SIGNAL: CONSTANT CURRENT
SG PI1–91 HO2 SENSOR HEATERS 1/2, 2/2 GROUND: GROUND
O PI1–92 HO2 SENSOR HEATER CONTROL – 1/2: PWM, 1 CYCLE PER 256 mS, POSITIVE DUTY CYCLE RANGE 0 mS = 0%, 77 mS = 30%, 256 mS = 100%
O PI1–93 HO2 SENSOR HEATER CONTROL – 2/2: PWM, 1 CYCLE PER 256 mS, POSITIVE DUTY CYCLE RANGE 0 mS = 0%, 77 mS = 30%, 256 mS = 100%
I PI1–94 BANK 1 CAMSHAFT SENSOR SIGNAL: PULSED SIGNAL, 4 PULSES PER ENGINE CYCLE
SG PI1–95 BANK 1 CAMSHAFT SENSOR GROUND: GROUND
I PI1–98 BANK 1 KNOCK SENSOR SIGNAL: VARIABLE VOLTAGE DEPENDENT ON ENGINE VIBRATION
I PI1–99 BANK 2 KNOCK SENSOR SIGNAL: VARIABLE VOLTAGE DEPENDENT ON ENGINE VIBRATION
SG PI1–100 SENSOR SHIELD: GROUND
I PI1–102 ACCELERATOR PEDAL POSITION SENSOR 1 SIGNAL: FOOT OFF = 0.75 V; FULLY DEPRESSED = 3.40 V (AUTO) 3.20 V (MAN)
I PI1–103 ACCELERATOR PEDAL POSITION SENSOR 2 SIGNAL: FOOT OFF = 3.38 V; FULLY DEPRESSED = 2.05 V (AUTO) 2.14 V (MAN)
I PI1–104 FUEL TANK PRESSURE SENSOR SIGNAL, NOMINAL 0 – 5 V: VOLTAGE INCREASES AS PRESSURE INCREASES
D PI1–105 SERIAL DATA LINK: SERIAL COMMUNICATION
O PI1–106 THROTTLE MOTOR DRIVE: B+ TO ACTIVATE MOTOR
I PI1–107 HO2 SENSOR 2/1 SIGNAL: VARIABLE CURRENT
I PI1–108 HO2 SENSOR 2/1 SIGNAL: CONSTANT CURRENT
SG PI1–111 FUEL INJECTORS 2, 3, 5, 8 GROUND: GROUND
SG PI1–116 FUEL INJECTORS 1, 4, 6, 7 GROUND: GROUND
C PI1–123 CAN –
C PI1–124 CAN +
I PI1–127 MAP SENSOR SIGNAL, NOMINAL 0 – 5 V: VOLTAGE INCREASES AS MANIFOLD ABSOLUTE PRESSURE INCREASES
I PI1–128 HO2 SENSOR 1/2 SIGNAL, NOMINAL 1 V SWING: 0.1 – 0.9 V SWING
I PI1–129 HO2 SENSOR 2/2 SIGNAL, NOMINAL 1 V SWING: 0.1 – 0.9 V SWING
SG PI1–130 HO2 SENSORS SHIELD: GROUND
B+ PI1–134 THROTTLE MOTOR POWER SUPPLY: B+ WHEN RELAY ACTIVATED

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 05.1
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationACTIVE BRAKE BOOSTER — — ENGINE COMPARTMENT BULKHEAD, DRIVER SIDE
ACTIVE BRAKE BOOSTER SOLENOID FH56 6-WAY / BLACK ENGINE COMPARTMENT, BRAKE BOOSTER
BRAKE FLUID RESERVOIR FH104 2-WAY / BLACK BRAKE BOOSTER
BRAKE PRESSURE SENSOR FH54 3-WAY / BLACK BRAKE MASTER CYLINDER, UNDERSIDE
CENTER CONSOLE SWITCH PACK FC113 8-WAY / BLACK CENTER CONSOLE
FC119 8-WAY / BLACK
DYNAMIC STABILITY CONTROL MODULE FH103 47-WAY / BLACK ENGINE COMPARTMENT, RH FRONT
PEDAL FORCE SWITCH FH56 6-WAY / BLACK ENGINE COMPARTMENT, BRAKE BOOSTER
PEDAL TRAVEL SENSOR FH11 3-WAY / BLACK ENGINE COMPARTMENT, BRAKE BOOSTER
STEERING ANGLE SENSOR FC110 4-WAY / GREY STEERING COLUMN
WHEEL SPEED SENSOR – LH FRONT FH115 2-WAY / BLACK LH FRONT WHEEL HUB
WHEEL SPEED SENSOR – LH REAR RL1 2-WAY / BLACK LH REAR WHEEL HUB
WHEEL SPEED SENSOR – RH FRONT FH116 2-WAY / BLACK RH FRONT WHEEL HUB
WHEEL SPEED SENSOR – RH REAR RR1 2-WAY / BLACK RH REAR WHEEL HUB
YAW RATE AND LATERAL ACCELERATION SENSORS CLUSTER CA236 6-WAY / BLACK UNDER CENTER CONSOLEHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFC10 14-WAY / GREEN / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FC26 16-WAY / BLUE / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, DRIVER SIDE
FH1 22-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH2 16-WAY / GREY / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH6 16-WAY GREEN / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST, ADJACENT TO FEM
RL2 2-WAY / BLACK / LH REAR LINK REAR SUSPENSION SUBFRAME RH SIDE
RR2 2-WAY / BLACK / RH REAR LINK REAR SUSPENSION SUBFRAME RH SIDEGROUNDS
Ground LocationFC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH42 ENGINE COMPARTMENT, BEHIND RH HEADLAMP
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Dynamic Stability Control Module
Pin Description and CharacteristicB+ FH103–1 BATTERY POWER SUPPLY – PUMP: B+
— FH103–3 STEERING ANGLE SENSOR SIGNAL (A): PULSED SIGNAL
B+ FH103–4 IGNITION SWITCHED POWER SUPPLY (II): B+
SG FH103–5 SENSOR GROUND – YAW RATE, STEERING ANGLE SENSORS: GROUND
I FH103–6 STEERING ANGLE SENSOR SIGNAL (B): PULSED SIGNAL
SS FH103–7 YAW RATE, STEERING ANGLE SENSORS SUPPLY VOLTAGE: B+
SG FH103–8 BRAKE FLUID LEVEL SENSOR SIGNAL GROUND: GROUND
I FH103–9 BRAKE FLUID LEVEL SENSOR SIGNAL: BRAKE FLUID LEVEL LOW = GROUND
C FH103–11 CAN +
C FH103–12 CAN +
O FH103–13 VEHICLE SPEED SIGNAL (SLIDING ROOF THRESHOLD): < 62 KM/H (38.5 MPH) = GROUND; > 62 KM/H (38.5 MPH) = B+
C FH103–14 CAN –
C FH103–15 CAN –
PG FH103–16 POWER GROUND – VALVES: GROUND
SS FH103–17 ACTIVE BRAKE BOOSTER SOLENOID SUPPLY VOLTAGE: NOMINAL 5 V
SS FH103–18 BRAKE PRESSURE SENSOR SUPPLY VOLTAGE: NOMINAL 5 V
SG FH103–19 SENSOR GROUND – BRAKE PRESSURE SENSOR: GROUND
I FH103–20 BRAKE PRESSURE SENSOR SIGNAL, NOMINAL 0.5 – 4.5 V: VOLTAGE INCREASES AS PRESSURE INCREASES
SG FH103–24 ACTIVE BRAKE BOOSTER TRAVEL SENSOR SIGNAL GROUND: GROUND
C FH103–25 CAN – (LOCAL)
SS FH103–26 ACTIVE BRAKE BOOSTER TRAVEL SENSOR SUPPLY VOLTAGE: NOMINAL 5 V
SS FH103–27 ACTIVE BRAKE BOOSTER FORCE SWITCH NORMALLY OPEN (NOMINAL 5 V): OPEN / CLOSED CIRCUIT
I FH103–28 ACTIVE BRAKE BOOSTER FORCE SWITCH SIGNAL: GROUND
C FH103–29 CAN + (LOCAL)
SS FH103–30 ACTIVE BRAKE BOOSTER FORCE SWITCH NORMALLY CLOSED (NOMINAL 5 V): CLOSED / OPEN CIRCUIT
O FH103–31 ACTIVE BRAKE BOOSTER SOLENOID DRIVE: GROUND (PWM)
B+ FH103–32 BATTERY POWER SUPPLY – VALVES: B+
SG FH103–33 RH FRONT WHEEL SPEED SENSOR SIGNAL GROUND: GROUND
I FH103–34 RH FRONT WHEEL SPEED SENSOR SIGNAL: 46 PULSES PER WHEEL REVOLUTION
I FH103–36 LH REAR WHEEL SPEED SENSOR SIGNAL: 46 PULSES PER WHEEL REVOLUTION
SG FH103–37 LH REAR WHEEL SPEED SENSOR SIGNAL GROUND: GROUND
I FH103–38 DYNAMIC STABILITY CONTROL SWITCH: NORMALLY OPEN / GROUND WHEN ACTIVATED
I FH103–40 ACTIVE BRAKE BOOSTER TRAVEL SENSOR SIGNAL, NOMINAL 0.5 – 4.5 V: VARIABLE VOLTAGE
SG FH103–42 RH REAR WHEEL SPEED SENSOR SIGNAL GROUND: GROUND
I FH103–43 RH REAR WHEEL SPEED SENSOR SIGNAL: 46 PULSES PER WHEEL REVOLUTION
I FH103–45 LH FRONT WHEEL SPEED SENSOR SIGNAL: 46 PULSES PER WHEEL REVOLUTION
SG FH103–46 LH FRONT WHEEL SPEED SENSOR SIGNAL GROUND: GROUND
PG FH103–47 POWER GROUND – PUMP: GROUND

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 05.2
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationCLUTCH PEDAL POSITION SENSOR CA287 6-WAY / BLACK TOP OF CLUTCH PEDAL
ELECTRONIC PARKING BRAKE SWITCH CA243 8-WAY / BLACK CENTER CONSOLE
FRONT ELECTRONIC MODULE CA24 26-WAY / NATURAL LH ‘A’ POST
CA31 20-WAY / BLACK
FH9 22-WAY / BLACK
FH59 12-WAY / BLACK
FH60 17-WAY / BLACK
NEUTRAL SWITCH (DIESEL) GB4 4-WAY / GREY TRANSMISSION, LH REAR
NEUTRAL SWITCH (GASOLINE) GB3 2-WAY / BLACK TRANSMISSION, LH REAR
PARKING BRAKE MODULE CA265 14-WAY / GREY LUGGAGE COMPARTMENT, RH REAR CA266 24-WAY / BLACK
PARKING BRAKE MOTOR CA269 6-WAY / GREY REAR SUSPENSION SUBFRAME
VARIABLE ASSIST STEERING ACTUATOR FH16 2-WAY / BLACK STEERING RACK PINION HOUSINGHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFH1 22-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
GB1 16-WAY / GREY / ENGINE HARNESS TO TRANSMISSION HARNESS ADJACENT TO TRANSMISSION BELL HOUSING
PI42 8-WAY / BLACK / ENGINE HARNESS TO FRONT HARNESS ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationCA141 UNDER LH FRONT SEAT
CA156 LUGGAGE COMPARTMENT, RH SIDE
FH77 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (FORWARD OF CA30)
PI40 (LHD) ENGINE COMPARTMENT, BEHIND RH WHEEL ARCH LINER
PI40 (RHD) ENGINE COMPARTMENT, BEHIND LH WHEEL ARCH LINER
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Parking Brake Module Pin Description and CharacteristicI CA265–3 IN-GEAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
SS CA265–5 SIGNAL SUPPLY VOLTAGE: NOMINAL 5 V
I CA265–6 CLUTCH PEDAL POSITION SENSOR FEEDBACK SIGNAL: VARIABLE VOLTAGE
O CA265–7 PARKING BRAKE MOTOR ENGAGE: ACTIVATE = B+
I CA265–10 PARKING BRAKE SWITCH – APPLY: CHANGE IN RESISTANCE
I CA265–11 PARKING BRAKE SWITCH – RELE ASE: CHANGE IN RESISTANCE
SS CA265–12 SIGNAL SUPPLY VOLTAGE: NOMINAL 5 V
SG CA265–13 SIGNAL GROUND: GROUND
O CA265–14 PARKING BRAKE MOTOR DISENGAGE: ACTIVATE = B+
B+ CA266–1 BATTERY POWER SUPPLY: B+
SG CA266–3 SIGNAL GROUND: GROUND
S CA266–4 SCP –
S CA266–5 SCP +
I CA266–10 PARKING BRAKE MOTOR POSITION SENSOR FEEDBACK SIGNAL: VARIABLE VOLTAGE
PG CA266–12 POWER GROUND: GROUND
PG CA266–13 POWER GROUND: GROUNDFront Electronic Module
Pin Description and CharacteristicS FH59–1 SCP –
S FH59–7 SCP +
PG FH59–12 POWER GROUND: GROUND
B+ FH60–1 SWITCHED SYSTEM POWER SUPPLY: B+
I FH60–2 VARIABLE ASSIST STEERING ACTUATOR RETURN: VARIABLE VOLTAGE
O FH60–9 VARIABLE ASSIST STEERING ACTUATOR DRIVE: B+ (PWM)
PG FH60–11 POWER GROUND: GROUND
PG FH60–13 POWER GROUND: GROUND
PG FH60–14 POWER GROUND: GROUND
PG FH60–15 POWER GROUND: GROUND

Suspension Adaptive Damping
Jaguar S-TYPE 2005
Suspension Adaptive Damping
Fig. 05.4
13 4114
46 80
76 77 92
ll
15 45ll ll SS
81 118EE
Fig .01.1
Fig .01 .2 F
ig .01.3
Fig .01 .4
Fig . 01.5 F
ig . 01.6 F
ig .01 .7
Input
OutputI
O
B
P+Battery VoltagePower Ground Sensor/Signal Supply V
Sensor/Signal Ground Serial and Encoded Data
CAN
+
SCPC
S DD
–
D2B Network2
f05_4_200045
FC9-29 FC9-28
G Y
U Y
20.220.2
CA11-14
CA11-13
SS
SS
FC9-26 FC9-25
U Y
20.220.2
CA11-10
FH117-1
FH117-2FH118-1
FH118-2CA140-1
CA140-2CA111-1
CA111-2
CA11-2
BG
CA11-1
O
WB
CA11-4
BO
CA11-3
O
W
CA11-7
BG
CA11-8
O
WU
CA11-5
BW
CA11-6
O
WG
OOOO
BG WUBW WGBG WB BO W
BCA11-12
NG
CA11-16
NW
29
FH103-14 FH103-11
G Y
20.1
SS
CA102-2 CA102-1
U Y
20.220.2
FH6-12
FH6-13
FH2-9
FH2-10
FH70-2
WB
FH70-3
FH70-1
N Y
FH63-1
FH63-2
YR
FH63-3
N Y
CA17-1
CA17-2 CA17-3
YB N Y
I
CA11-9
N
CA12-9
Y
CA12-11
WB
CA12-12
YR
CA12-10
YB
II
FHS31
CAS54
41II
BB
CCCC
FH103-15 FH103-12
G Y
CC
FC9-13 FC9-12
G Y
CC
CAS53
FHS30
N
Y
FH6-8
FH6-2
FH6-10FH6-11
P
20.120.120.120.120.120.120.1
LH FRONT DAMPER SOLENOID
SYSTEM STATE
VEHICLE SPEED
DYNAMIC STABILITY CONTROL MODULE
INSTRUMENT CLUSTER
REAR ELECTRONIC MODULE
BRAKE ON / OFF
CA158
ADAPTIVE DAMPING CONTROL MODULE RH FRONT DAMPER SOLENOID
LH REAR DAMPER SOLENOID
RH REAR DAMPER SOLENOID
LATERAL ACCELEROMETER
FRONT VERTICAL ACCELEROMETER
REAR VERTICAL ACCELEROMETER
VARIANT: Adaptive Damping Vehicles
VIN RANGE: All
DATE OF ISSUE: May 2004

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.DATE OF ISSUE: May 2004
Fig. 08.5
COMPONENTS
Component Connector(s) Connector Description LocationAUXILIARY LIGHTING SWITCH FC11 10-WAY / YELLOW FASCIA, ADJACENT TO STEERING COLUMN
HEADLAMP LEVELING ACTUATOR – LH HL1 3-WAY / BLACK BEHIND LH HEADLAMP UNIT
HEADLAMP LEVELING ACTUATOR – RH HR1 3-WAY / BLACK BEHIND RH HEADLAMP UNIT
HEADLAMP LEVELING CONTROL MODULE FH12 26-WAY / BLACK RH ‘A’ POST, ABOVE PRIMARY JUNCTION FUSE BOX
HID HEADLAMP UNIT – LH HL10 4-WAY / BLACK ENGINE COMPARTMENT, LH FRONT
HID HEADLAMP UNIT – RH HR10 4-WAY / BLACK ENGINE COMPARTMENT, RH FRONT
RIDE HEIGHT SENSOR – FRONT AXLE FH113 6-WAY / BLACK RH FRONT SUSPENSION
RIDE HEIGHT SENSOR – REAR AXLE CA240 6-WAY / BLACK RH REAR SUSPENSIONHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFC4 14-WAY / GREEN / FASCIA HARNESS IN-LINE CONNECTOR BEHIND INSTRUMENT PANEL, LH SIDE
FH2 16-WAY / GREY / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH39 12-WAY / GREY / FRONT HARNESS TO RH FRONT HEADLAMP LINK BEHIND FRONT BUMPER, RH SIDE
FH40 12-WAY / GREY / FRONT HARNESS TO LH FRONT HEADLAMP LINK BEHIND FRONT BUMPER, LH SIDEGROUNDS
Ground LocationFC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH22 ENGINE COMPARTMENT, BEHIND LH HEADLAMP
FH42 ENGINE COMPARTMENT, BEHIND RH HEADLAMP