2005 JAGUAR S TYPE fuel system

child restraint manual radio set immobilizer odometer charging oil additives

Page 9 of 200

JAGUAR S TYPE 2005 1.G Electrical Manual
DATE OF ISSUE: May 20045
Abbreviations and AcronymsJaguar S-TYPE 2005
The following abbreviations and acronyms are used throughout this Electrical Guide:A/C Air Conditioning
A/CCM Air Conditioning Co

DATE OF ISSUE: May 20045
Abbreviations and AcronymsJaguar S-TYPE 2005
The following abbreviations and acronyms are used throughout this Electrical Guide:A/C Air Conditioning
A/CCM Air Conditioning Control Module
ACT SENSOR Air Charge Temperature Sensor
APP SENSOR Accelerator Pedal Position Sensor APP1 Accelerator Pedal Position Sensor Element 1
APP2 Accelerator Pedal Position Sensor Element 2ASC Adaptive Speed Control
AUTO Automatic Transmission B+ Battery Voltage
BANK 1 RH Cylinder Bank
BANK 2 LH Cylinder Bank CAN Controller Area Network
CKP SENSOR Crankshaft Position Sensor CM Control Module
CMP SENSOR / 1 Camshaft Position Sensor / RH Bank
CMP SENSOR / 2 Camshaft Position Sensor / LH Bank D2B D2B Network
DDM Driver Door Module DSC Dynamic Stability Control
DSM Driver Seat Module
ECM Engine Control Module
ECT SENSOR Engine Coolant Temperature Sensor EFT SENSOR Engine Fuel Temperature Sensor
EGR Exhaust Gas Recirculation
EGT SENSOR Exhaust Gas Temperature Sensor
EOT SENSOR Engine Oil Temperature Sensor
EVAP CANISTER CLOSE VALVE Evaporative Emission Canister Close Valve
EVAP CANISTER PURGE VALVE Evaporative Emission Canister Purge Valve FEM Front Electronic Module
FPDB Front Power Distribution Box
FRP SENSOR Fuel Rail Pressure Sensor FTP SENSOR Fuel Tank Pressure Sensor
GPS Global Positioning SystemHID High Intensity Discharge
HO2 SENSOR 1 / 1 Heated Oxygen Sensor – RH Bank / Upstream
HO2 SENSOR 1 / 2 Heated Oxygen Sensor – RH Bank / Downstream
HO2 SENSOR 2 / 1 Heated Oxygen Sensor – LH Bank / Upstream
HO2 SENSOR 2 / 2 Heated Oxygen Sensor – LH Bank / Downstream
IAT SENSOR Intake Air Temperature Sensor IC Instrument Cluster
ICE In-Car Entertainment System
IMT VALVE / 1 Intake Manifold Tuning Valve / Top
IMT VALVE / 2 Intake Manifold Tuning Valve / Bottom IP SENSOR Injection Pressure Sensor
KS / 1 Knock Sensor / RH Bank
KS / 2 Knock Sensor / LH BankLH Left-Hand
LHD Left-Hand Drive
MAF SENSOR Mass Air Flow Sensor MAN Manual Transmission
MAP SENSOR Manifold Absolute Pressure Sensor N/A Normally Aspirated
NAS North American Specification
NCM Navigation Control Module PAM Parking Aid Module
PATS Passive Anti-Theft System
PJB Primary Junction Box
PWM Pulse Width Modulated RCM Restraints Control ModuleREM Rear Electronic Module RH Right-Hand
RHD Right-Hand Drive
ROW Rest of World
RPDB Rear Power Distribution Box SC Supercharged
SCLM Steering Column Lock Module SCM Speed Control ModuleSCP Standard Corporate Protocol Network

Page 13 of 200

JAGUAR S TYPE 2005 1.G Electrical Manual
DATE OF ISSUE: May 20049
User InstructionsJaguar S-TYPE 2005
Battery; Starter; Generator: V6Battery; Starter; Generator: V6
VARIANT: V6 Vehicles
VIN RA NGE: All
DATE OF ISSUE: February 2004f02_1_2000

DATE OF ISSUE: May 20049
User InstructionsJaguar S-TYPE 2005
Battery; Starter; Generator: V6Battery; Starter; Generator: V6
VARIANT: V6 Vehicles
VIN RA NGE: All
DATE OF ISSUE: February 2004f02_1_200045
Y
FPDB MEGAFUSE
STARTER MEGAFUSEMEGAFUSE ASSEMBLYBATTERY
FAULT;
CHARGE WARNING
B
JB1
CA288 CA280 CA304450A
250A CA302
CA135
R
R
R
R01.1REAR POWER DISTRIBUTION
FUSE BOX
WUKEY-IN0FC18-5
I
II
III
FC18-7
FC18-4
NR7
IGNITION SWITCHFC18-1
WG
WB01.5IGNITION SWITCHED
CIRCUITS (II)
NG56S FC52-1
PASSIVE ANTI-THEFT SYSTEM TRANSCEIVER
FC52-3
FC52-4
FC52-2WR YRBG
WU
FC37-3 FH53-3
FHS63
PI41-34
F1 5AYYY
PRIMARY JUNCTION FUSE BOX
GB2-9
GB2-10GB1-10GB1-9
GB2-13
GB2-16GO
GRBB
BB BB+O
P
P, N
P18II
PIS30 PI40ALTRANSMISSION CONTROL MODULE
92NR GR GR GR GRCA286-1 CA286-2 FH3-10PI42-8 GB1-13CLUTCH PEDAL SAFETY SWITCH
85NG
WG35II FC8-14 FC8-15
FC9-31 FC9-16 FC9-32FC8-5PASSIVE
ANTI-THEFT
SYSTEM
LOGICB+B+
C
C
D I
D P
P
INSTRUMENT CLUSTER
YFC9-28GFC9-29BFC8-32BFC8-2
FC38
20.1 20.1O.K .TO START
YYPIS27 GB1-14(MAN / ROW)(MAN / NAS) (AUTO)
JUNCTION BLOCKST11 ST12R3
FRONT BULKHEADFH83
CA177FH672
STARTER RELAY
NW
GW
GO65ST4-1
R20
FRONT POWER DISTRIBUTION FUSE BOX
PI41-40
STARTER MOTORR
B R
GW
ST5
ST6
ST3
ST2
GB1-6 PI1-41
PI1-31 PI1-6
PI1-124
PI1-123
GO GR Y
GENERATOR WARNING; CLUTCH DISENGAGEDY
G20.1 20.1
P, NSTART
ENGINE
CRANK
ENGINE
REQUESTO
I
II
I
O
C
C
ENGINE CONTROL MODULE
PI1-65
PI1-53
PI1-79 PI47-3
PI47-2
PI47-1
PI47-4WG YR
WR GO
20IIB+ST7
FIELD
CONTROL
GENERATOR
13 4
114
46 80
76 77 92ll15 45ll ll SS81 118EEFig. 01.1
Fig. 01.2 Fig. 01.3
Fig. 01.4
Fig. 01.5Fig. 01.6
Fig. 01.7Input
OutputI
OB
P+Battery Voltage Power Ground Sensor/Signal Supply V
Sensor/Signal Ground Serial and Encoded Data
CAN+SCPC
S DD–D2B Network2
Fig.
02.1
Fig. 02.1
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all ciruit connections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
IInput
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
SSCPNetwork
D2 D2B Network
D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furhished to aid the user in understanding circuit operation. THIS INFORMATION SHOULD BE USED FOR
REFERENCE ONLY. Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
DATE OF ISSUE: February 2004
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description Location
BATTERY —— LUGGAGECOMPARTMENT
CLUTCH PEDAL SAFETY SWITCH CA286 2-WAY / BLACK TOP OF CLUTCH PEDAL (BOTTOM SWITCH)
ENGINE CONTROL MODULE PI1 134-WAY / BLACK FRONT BULKHEAD, PASSENGER SIDE
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
GENERATOR (V6) PI47 4-WAY / BLACK ENGINE, RH SIDE, FRONT ST7 EYELET
IGNITION SWITCH FC18 7-WAY / BLACK STEERING COLUMN COWLING
INSTRUMENT CLUSTER FC14 22-WAY / GREY INSTRUMENT PANEL FC15 20-WAY / BLACK
FC63 22-WAY / BLACK
PASSIVE ANTI-THEFT SYSTEM TRANSCEIVER FC52 4-WAY / GREEN STEERING COLUMN, IGNITION SWITCH
PRIMARY JUNCTION FUSE BOX CA2 26-WAY / BLACK RH ‘A’ POST
CA56 8-WAY / BLACK
FC37 26-WAY / BLACK
FH7 6-WAY / BLACK
FH53 10-WAY / BLACK
STARTER MEGAFUSE — — LUGGAGE COMPARTMENT
STARTER MOTOR — — ENGINE BLOCK, RH SIDE
STARTER RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R20
TRANSMISSION CONTROL MODULE GB2 16-WAY / BLACK TRANSMISSION CONTROL VALVE ASSEMBLY
HARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFH3 16-WAY / BLUE / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST
GB1 16-WAY / GREY / ENGINE HARNESS TO TRANSMISSION HARNESS ADJACENT TO TRANSMISSION BELL HOUSING
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDE
PI42 8-WAY / BLACK / ENGINE HARNESS TO FRONT HARNESS ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDE
ST4 2-WAY / GREY / FRONT HARNESS TO STARTER LINK ENGINE COMPARTMENT, REARWARD OF RH WHEEL ARCH
GROUNDS
Ground LocationFC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
JB1 LUGGAGE COMPARTMENT, BATTERY GROUND
PI40(LHD) ENGINECOMPARTMENT,BEHINDRHWHEELARCHLINER
PI40 (RHD) ENGINE COMPARTMENT, BEHIND LH WHEEL ARCH LINER
ST2 ENGINE COMPARTMENT, BEHIND LH WHEEL ARCH LINER
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Engine Control Module Pin Description and Characteristic
IPI1–6 ENGINECRANK:B+
I PI1–31 AUTOMATIC – PARK / NEUTRAL SIGNAL: B+ WHEN ACTIVATED MANUAL, ROW – PARK / NEUTRAL SIGNAL: B+ WHEN IGNITION CRANK (III)
MANUAL, NAS – CLUTCH PEDAL SAFETY SWITCH (PARK / NEUTRAL SIGNAL): B+ WHEN ACTIVATED
O PI1–41 STARTER RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–53 FUEL PUMP 2 DRIVE (TO FUEL PUMP 2 MODULE): PWM, 150 Hz, NORMAL POSITIVE DUTY CYCLE RANGE = 4% – 51%
I PI1–65 GENERATOR FIELD RETURN SIGNAL: VARIABLE VOLTAGE BY GENERATOR OPERATING CONDITION
I PI1–79 GENERATOR FAULT; CHARGE WARNING
C PI1–123 CAN –
C PI1–124 CAN +
Instrument Cluster
Pin Description and CharacteristicI FC14–2 KEY-IN AUDIBLE WARNING: B+ WHEN KEY IN
B+ FC14–3 IGNITION SWITCHED POWER SUPPLY (II): B+
SG FC14–14 SIGNAL GROUND: GROUND
PG FC15–2 POWER GROUND: GROUND
B+ FC15–3 BATTERY POWER SUPPLY (LOGIC): B+
I FC15–4 PATS GROUND: GROUND
D FC15–5 PATS TRANSCEIVER: ENCODED COMMUNICATION
D FC15–6 PATS TRANSCEIVER: ENCODED COMMUNICATION
C FC15–18 CAN +
C FC15–19 CAN –
Transmission Control ModulePin Description and CharacteristicB+ GB2–9 IGNITION SWITCHED POWER SUPPLY: B+
O GB2–10 PARK / NEUTRAL SIGNAL: GROUND WHEN ACTIVATED
PG GB2–13 POWER GROUND: GROUND
PG GB2–16 POWER GROUND: GROUND
CONTROL MODULE PIN OUT INFORMATION FIGURE NUMBERCOMPONENT, CONNECTOR AND GROUND
INFORMATION
DATE OF ISSUE
FIGURE MODEL RANGE AND YEAR
TITLE FIGURE NUMBER
KEY TO REFERENCE SYMBOLS VARIANT, VIN RANGE AND DATE OF ISSUE
DATA PAGE
FIGURE PAGE

Page 19 of 200

JAGUAR S TYPE 2005 1.G Electrical Manual
DATE OF ISSUE: May 200415
Relay and Fuse LocationJaguar S-TYPE 2005
R7
F8
5A
F1
5AF3
5AF4
5AF5
10AF6
10AF7
5A
F22
10A
F9
10A
F23
10A
F10 5A
F24
5A
F11
10A
F25
10A
F12
15A
F26
5A
F135A
F27
10A
F15 5A

Page 54 of 200

JAGUAR S TYPE 2005 1.G Electrical Manual
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NO

Page 84 of 200

Page 106 of 200

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 09.2
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAIR CONDITIONING CONTROL MODULE – PANEL FC27 26-WAY / GREY CENTER CONSOLE
FC28 22-WAY / GREY
AUDIO UNIT FC94 20-WAY / BLACK CENTER CONSOLE
FC96 ANTENNA CONNECTOR
FC108 FIBER OPTIC CONNECTOR
AUXILIARY LIGHTING SWITCH FC11 10-WAY / YELLOW FASCIA, ADJACENT TO STEERING COLUMN
CENTER CONSOLE SWITCH PACK FC113 8-WAY / BLACK CENTER CONSOLE FC119 8-WAY / BLACK
CIGAR LIGHTER CA109 3-WAY / BLACK CENTER CONSOLE
DOOR SWITCH PACK – DRIVER DD2 26-WAY / YELLOW DRIVER DOOR ARM REST
FRONT ELECTRONIC MODULE CA24 26-WAY / NATURAL LH ‘A’ POST CA31 20-WAY / BLACK
FH9 22-WAY / BLACK
FH59 12-WAY / BLACK
FH60 17-WAY / BLACK
FUEL FLAP / TRUNK RELEASE SWITCH PACK FC43 10-WAY / GREY INSTRUMENT PANEL
INSTRUMENT CLUSTER FC8 32-WAY / BLACK INSTRUMENT PANEL
FC9 32-WAY / BLACK
J-GATE MODULE CA245 16-WAY / BLACK J-GATE ASSEMBLY
MAIN LIGHTING SWITCH (COLUMN SWITCHGEAR) FC116 6-WAY / BLACK STEERING COLUMN COWLING
POWER POINT CA237 3-WAY / BROWN ADJACENT TO CIGAR LIGHTER
PRIMARY JUNCTION FUSE BOX CA2 26-WAY / BLACK RH ‘A’ POST CA56 8-WAY / BLACK
FC37 26-WAY / BLACK
FH7 6-WAY / BLACK
FH53 10-WAY / BLACK
ROOF CONSOLE CA250 22-WAY / BLACK ROOF HEADLINER
STEERING WHEEL LIGHTING SQ1 4-WAY / BLACK STEERING WHEEL SQ3 4-WAY / BLACK
TELEMATICS DISPLAY FC92 22-WAY / BLACK CENTER CONSOLE
WINDOW SWITCH – LH REAR CA78 5-WAY / GREEN LH REAR DOOR ARM REST
WINDOW SWITCH – PASSENGER PD1 5-WAY / GREEN PASSENGER DOOR ARM REST
WINDOW SWITCH – RH REAR CA95 5-WAY / GREEN RH REAR DOOR ARM RESTHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationDD8 16-WAY / BLUE / CABIN HARNESS TO DRIVER DOOR HARNESS DRIVER DOOR
FC23 10-WAY / GREY / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, LH SIDE
FC117 10-WAY / BLACK / STEERING WHEEL CASSETTE STEERING COLUMN
PD4 10-WAY / GREY / CABIN HARNESS TO PASSENGER DOOR HARNESS PASSENGER DOORGROUNDS
Ground LocationCA30 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (REARWARD OF FH77)
CA50 RH LOWER ‘A’ POST, BELOW PRIMARY JUNCTION FUSE BOX
CA141 UNDER LH FRONT SEAT
CA154 UNDER RH FRONT SEAT
FC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH77 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (FORWARD OF CA30)
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Air Conditioning Control Module – Panel Pin Description and CharacteristicI FC28–15 PANEL ILLUMINATION (DIMMER-CONTROLLED): B+ (PWM)Audio UnitPin Description and CharacteristicI FC94–17 DIMMER-CONTROLLED ILLUMINATION: PWM, 80 Hz, GROUND = 0% DUTY CYCLE, B+ = 100% DUTY CYCLEFront Electronic ModulePin Description and CharacteristicB+ CA31–1 SWITCHED SYSTEM POWER SUPPLY: B+
O CA31–11 BACKLIGHTING ACTIVATE: B+ (PWM)
S FH59–1 SCP –
B+ FH59–6 BATTERY POWER SUPPLY (LOGIC): B+
S FH59–7 SCP +
PG FH59–12 POWER GROUND: GROUND
PG FH60–11 POWER GROUND: GROUND
PG FH60–13 POWER GROUND: GROUND
PG FH60–14 POWER GROUND: GROUND
PG FH60–15 POWER GROUND: GROUNDInstrument ClusterPin Description and CharacteristicPG FC8–2 POWER GROUND: GROUND
SS FC8–11 DIMMER SUPPLY VOLTAGE: B+
B+ FC8–15 BATTERY POWER SUPPLY (LOGIC): B+
SG FC8–18 AUXILIARY LIGHTING SWITCH SIGNAL GROUND: GROUND
SG FC8–32 SIGNAL GROUND: GROUND
I FC9–2 MAIN LIGHTING SWITCH SIGNALS – OFF, SIDE, DIP, AUTOLAMP: VARIABLE RESISTANCE
I FC9–4 DIMMER SIGNAL: VARIABLE VOLTAGE
I FC9–5 MAIN LIGHTING SWITCH SIGNALS – EXIT DELAY: VARIABLE RESISTANCE
SG FC9–10 MAIN LIGHTING SWITCH SIGNAL GROUND: GROUND
S FC9–25 SCP +
S FC9–26 SCP –

Page 126 of 200

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 12.1
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationCENTER CONSOLE SWITCH PACK FC113 8-WAY / BLACK CENTER CONSOLE
FC119 8-WAY / BLACK
DOOR LATCH ASSEMBLY – DRIVER DT5 10-WAY / BLACK DRIVER DOOR
DOOR LATCH ASSEMBLY – LH REAR CA81 10-WAY / BLACK LH REAR DOOR
DOOR LATCH ASSEMBLY – PASSENGER PT3 10-WAY / BLACK PASSENGER DOOR
DOOR LATCH ASSEMBLY – RH REAR CA90 10-WAY / BLACK RH REAR DOOR
DRIVER DOOR MODULE CA85 12-WAY / BLACK DRIVER DOOR DD4 26-WAY / NATURAL
DT2 20-WAY / BLACK
EXTERNAL TRUNK RELEASE SWITCH CA97 2-WAY / BLACK LUGGAGE COMPARTMENT LID
FRONT ELECTRONIC MODULE CA24 26-WAY / NATURAL LH ‘A’ POST CA31 20-WAY / BLACK
FH9 22-WAY / BLACK
FH59 12-WAY / BLACK
FH60 17-WAY / BLACK
FUEL FLAP AND TRUNK RELEASE SWITCH PACK FC43 10-WAY / GREY INSTRUMENT PANEL
FUEL FLAP RELAY — — REAR POWER DISTRIBUTION FUSE BOX – R8
FUEL FLAP RELEASE SOLENOID CA7 2-WAY / BLACK LUGGAGE COMPARTMENT, RH SIDE, FRONT
REAR ELECTRONIC MODULE CA63 17-WAY / BLACK LUGGAGE COMPARTMENT, RH REAR CA100 12-WAY / BLACK
CA101 20-WAY / BLACK
CA102 22-WAY / BLACK
CA103 26-WAY / NATURAL
REAR POWER DISTRIBUTION FUSE BOX — — LUGGAGE COMPARTMENT
REMOTE KEYLESS ENTRY MODULE CA303 4-WAY / BLACK UNDER CENTER CONSOLE
TRUNK AJAR SWITCH CA26 4-WAY / BLACK LUGGAGE COMPARTMENT LID
TRUNK RELEASE SOLENOID CA26 4-WAY / BLACK LUGGAGE COMPARTMENT LID
VALET SWITCH VS1 6-WAY / BLACK GLOVE BOXHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationDT8 14-WAY / GREY / CABIN HARNESS TO DRIVER DOOR TRIM HARNESS DRIVER DOOR
DT10 10-WAY / GREY / CABIN HARNESS TO DRIVER DOOR TRIM HARNESS DRIVER DOOR
FC23 10-WAY / GREY / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, LH SIDE
FC33 16-WAY / GREEN / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FC39 10-WAY / GREY / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FC121 4-WAY / GREY / FASCIA HARNESS IN-LINE CONNECTOR BEHIND GLOVE BOX
PT1 14-WAY / GREY / CABIN HARNESS TO PASSENGER DOOR TRIM HARNESS PASSENGER DOORGROUNDS
Ground LocationCA30 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (REARWARD OF FH77)
CA50 RH LOWER ‘A’ POST, BELOW PRIMARY JUNCTION FUSE BOX
CA141 UNDER LH FRONT SEAT
CA154 UNDER RH FRONT SEAT
CA156 LUGGAGE COMPARTMENT, RH SIDE
FC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH77 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (FORWARD OF CA30)
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Driver Door Module
Pin Description and CharacteristicI CA85–2 LOCK / UNLOCK STATUS SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
S CA85–3 SCP +
S CA85–4 SCP –
SG CA85–7 SIGNAL GROUND: GROUND
PG CA85–8 POWER GROUND: GROUND
PG CA85–9 REMOTE KEYLESS ENTRY MODULE GROUND: GROUND
I CA85–10 DOUBLE LOCK STATUS SWITCH (N ORMALLY OPEN): OPEN CIRCUIT / GROUND
B+ CA85–11 BATTERY POWER SUPPLY: B+
B+ CA85–12 SWITCHED SYSTEM POWER SUPPLY: B+
O DT2–6 REMOTE KEYLESS ENTRY MODULE POWER SUPPLY: B+
O DT2–8 LOCK DRIVE: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
O DT2–9 UNLOCK DRIVE: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
O DT2–10 DOUBLE LOCK DRIVE: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
D DT2–13 REMOTE KEYLESS ENTRY MODULE SIGNAL: ENCODED COMMUNICATIONS
I DT2–16 DRIVER DOOR ALARM SET / LOCK SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
I DT2–17 DRIVER DOOR ALARM RESET / UNLOCK SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
D DT2–18 REMOTE KEYLESS ENTRY MODULE SIGNAL: ENCODED COMMUNICATIONSFront Electronic Module
Pin Description and CharacteristicI CA24–4 NON-VALET VEHICLES – EXTERNAL TRUNK REL EASE SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
VALET VEHICLES – EXTERNAL TRUNK RELEASE SWITCH (NORMALLY OPEN) / VALET SWITCH (NORMALLY CLOSED): OPEN CIRCUIT / GROUND
I CA24–15 PASSENGER DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
I CA31–8 DRIVER DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
S FH59–1 SCP –
B+ FH59–6 BATTERY POWER SUPPLY (LOGIC): B+
S FH59–7 SCP +
B+ FH60–1 SWITCHED SYSTEM POWER SUPPLY: B+
PG FH60–11 POWER GROUND: GROUNDRear Electronic Module Pin Description and CharacteristicI CA100–9 GLOBAL CLOSE SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
B+ CA101–3 BATTERY POWER SUPPLY: B+
I CA101–17 LHD – RH REAR DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND RHD – LH REAR DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
I CA101–18 DOUBLE LOCK STATUS SWITCH (N ORMALLY OPEN): OPEN CIRCUIT / GROUND
I CA101–19 LOCK / UNLOCK STATUS SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
S CA102–1 SCP +
S CA102–2 SCP –
PG CA102–12 POWER GROUND: GROUND
I CA102–14 TRUNK AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
O CA103–4 LOCK DRIVE: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
O CA103–5 LOCK DRIVE: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
O CA103–6 UNLOCK DRIVE: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
O CA103–7 UNLOCK DRIVE: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
O CA103–8 DOUBLE LOCK DRIVE: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
O CA103–9 DOUBLE LOCK DRIVE: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
O CA103–10 TRUNK RELEASE DRIVE: TO AC TIVATE, DDM SWITCHES CIRCUIT TO B+
B+ CA103–13 SWITCHED SYSTEM POWER SUPPLY: B+
I CA103–16 LHD – LH REAR DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND RHD – RH REAR DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND

Page 128 of 200

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 12.2
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationCENTER CONSOLE SWITCH PACK FC113 8-WAY / BLACK CENTER CONSOLE
FC119 8-WAY / BLACK
DOOR LATCH ASSEMBLY – DRIVER DT5 10-WAY / BLACK DRIVER DOOR
DOOR LATCH ASSEMBLY – LH REAR CA81 10-WAY / BLACK LH REAR DOOR
DOOR LATCH ASSEMBLY – PASSENGER PT3 10-WAY / BLACK PASSENGER DOOR
DOOR LATCH ASSEMBLY – RH REAR CA90 10-WAY / BLACK RH REAR DOOR
DRIVER DOOR MODULE CA85 12-WAY / BLACK DRIVER DOOR DD4 26-WAY / NATURAL
DT2 20-WAY / BLACK
EXTERNAL TRUNK RELEASE SWITCH CA97 2-WAY / BLACK LUGGAGE COMPARTMENT LID
FRONT ELECTRONIC MODULE CA24 26-WAY / NATURAL LH ‘A’ POST CA31 20-WAY / BLACK
FH9 22-WAY / BLACK
FH59 12-WAY / BLACK
FH60 17-WAY / BLACK
FUEL FLAP AND TRUNK RELEASE SWITCH PACK FC43 10-WAY / GREY INSTRUMENT PANEL
FUEL FLAP RELAY — — REAR POWER DISTRIBUTION FUSE BOX – R8
FUEL FLAP RELEASE SOLENOID CA106 2-WAY / GREY LUGGAGE COMPARTMENT, RH SIDE, FRONT
REAR ELECTRONIC MODULE CA63 17-WAY / BLACK LUGGAGE COMPARTMENT, RH REAR CA100 12-WAY / BLACK
CA101 20-WAY / BLACK
CA102 22-WAY / BLACK
CA103 26-WAY / NATURAL
REAR POWER DISTRIBUTION FUSE BOX — — LUGGAGE COMPARTMENT
TRUNK LID LATCH ASSEMBLY CA26 4-WAY / BLACK LUGGAGE COMPARTMENT LID
VALET SWITCH VS1 6-WAY / BLACK GLOVE BOXHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationDT8 14-WAY / GREY / CABIN HARNESS TO DRIVER DOOR TRIM HARNESS DRIVER DOOR
FC23 10-WAY / GREY / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, LH SIDE
FC33 16-WAY / GREEN / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FC39 10-WAY / GREY / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FC121 4-WAY / GREY / FASCIA HARNESS IN-LINE CONNECTOR BEHIND GLOVE BOX
PT1 14-WAY / GREY / CABIN HARNESS TO PASSENGER DOOR TRIM HARNESS PASSENGER DOORGROUNDS
Ground LocationCA30 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (REARWARD OF FH77)
CA50 RH LOWER ‘A’ POST, BELOW PRIMARY JUNCTION FUSE BOX
CA141 UNDER LH FRONT SEAT
CA154 UNDER RH FRONT SEAT
CA156 LUGGAGE COMPARTMENT, RH SIDE
FC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH77 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (FORWARD OF CA30)
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Driver Door Module
Pin Description and CharacteristicI CA85–2 LOCK / UNLOCK STATUS SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
S CA85–3 SCP +
S CA85–4 SCP –
SG CA85–7 SIGNAL GROUND: GROUND
PG CA85–8 POWER GROUND: GROUND
B+ CA85–11 BATTERY POWER SUPPLY: B+
B+ CA85–12 SWITCHED SYSTEM POWER SUPPLY: B+
O DT2–8 LOCK DRIVE: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
O DT2–9 UNLOCK DRIVE: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
I DT2–16 DRIVER DOOR ALARM SET / LOCK SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
I DT2–17 DRIVER DOOR ALARM RESET / UNLOCK SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUNDFront Electronic ModulePin Description and CharacteristicI CA24–4 EXTERNAL TRUNK RELEASE SWITCH (NORMALLY OPEN) / VALET SWITCH (NORMALLY CLOSED): OPEN CIRCUIT / GROUND
I CA24–15 PASSENGER DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
I CA31–8 DRIVER DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
S FH59–1 SCP –
B+ FH59–6 BATTERY POWER SUPPLY (LOGIC): B+
S FH59–7 SCP +
B+ FH60–1 SWITCHED SYSTEM POWER SUPPLY: B+
PG FH60–11 POWER GROUND: GROUNDRear Electronic Module Pin Description and CharacteristicI CA100–9 GLOBAL CLOSE SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
B+ CA101–3 BATTERY POWER SUPPLY: B+
I CA101–17 LHD – RH REAR DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND RHD – LH REAR DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
I CA101–19 LOCK / UNLOCK STATUS SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
S CA102–1 SCP +
S CA102–2 SCP –
PG CA102–12 POWER GROUND: GROUND
I CA102–14 TRUNK AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
O CA103–4 LOCK DRIVE: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
O CA103–5 LOCK DRIVE: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
O CA103–6 UNLOCK DRIVE: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
O CA103–7 UNLOCK DRIVE: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
O CA103–10 TRUNK RELEASE DRIVE: TO AC TIVATE, DDM SWITCHES CIRCUIT TO B+
B+ CA103–13 SWITCHED SYSTEM POWER SUPPLY: B+
I CA103–16 LHD – LH REAR DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND RHD – RH REAR DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND

Load next 8 pages

Page: 1-8 9-16 next >

winter tires fuse box diagram clock catalytic converter radio deactivate passenger airbag