2005 JAGUAR S TYPE rear control
[x] Cancel search: rear controlPage 81 of 200
Dynamic Stability Control
Jaguar S-TYPE 2005
Dynamic Stability Control
Fig. 05.1
13 4114
46 80
76 77 92
ll
15 45ll ll SS
81 118EE
Fig .01.1
Fig .01 .2 F
ig .01.3
Fig .01 .4
Fig . 01.5 F
ig . 01.6 F
ig .01 .7
Input
OutputI
O
B
P+Battery VoltagePower Ground Sensor/Signal Supply V
Sensor/Signal Ground Serial and Encoded Data
CAN
+
SCPC
S DD
–
D2B Network2
f05_1_200045
BK
R
FH103-45
G
20.1
FH103-15
RWG
FH103-1
FH103-4
FH42
U
I
6615II
B
FH115-1 FH116-1
FH115-2
H
H
RW
FH103-32
69
BB
Y G
20.1
FH103-14
FH103-12
20.1
Y
YR
14.1
FH103-13 FH103-11
20.1
OCCCC––
FH103-16
B
FH103-47
B
PP
FH104-2 FH104-1FC119-4
B
FC38
UYFH103-38RU
O
FC113-8
B
FC113-4
RU
FC10-10
RL1-2 RR1-2NN
RL1-1 RR1-1H
H
FH103-46FH103-34FH103-33FH103-36FH103-37FH103-43FH103-42FH103-3
G B
N
B
N
YR
WR
Y
W
IIII
FH6-7
FH6-6
FH1-16 FH1-8 RL2-1
RL2-2
RR2-1
RR2-2
B N
B
N
FH54 -2
FH54 -3 FH54
-1
FH103-19
NW
FH103-18
YB
FH103-20
WB
I
FH103-6
Y
FH103-7
R
FH103-5
B
FH103-29
Y
FH103-25
U
FH103-24
WB
FH103-26
WR
FH103-40
W
FH103-27
WG
FH103-30
YR
FH103-28
NG
FH103-31
NR
FH103-17
WR
G
FC110 -3
Y
FC110-2
R
FC110-1
B
FC110-4
BKCA236 -5
R
CA236 -3
Y
CA236-2
U
CA236 -1
C
C
–
+
FC10-3
FC10-2
FC10-1
FC10-4
II
FCS18 FCS19
FC26-10
FC26-9
CC
FH2-14
FH2-13
+
R
B
FH11 -3
FH11-1 FH11
-2
FH56 -5 FH56
-2 FH56
-1
FH56
-4 FH56
-3
IO
WB
WR
W
WG
YR
NG
NR
WR
I
PEDAL TRAVEL SENSOR
CONTROL VALVES
PEDAL FORCESWITCH
ACTIVE BRAKE
BOOSTER SOLENOID
ACTIVE BRAKE BOOSTER
DYNAMIC STABILITY CONTROL
MODULE
VALVES
PUMP
PRESSURE PUMP
CENTER CONSOLE SWITCH PACK
TRACTION CONTROL SWITCHES BRAKE FLUID
RESERVOIR
FH103-8
FH103-9
REFER TO APPENDIX
DSC / CAN MESSAGES
SLIDING ROOF: VEHICLE SPEED(CIRCUIT CONTINUED) PUMP
VALVES
LOCAL
BRAKE PRESSURE SENSOR LH FRONT
WHEEL SPEED SENSOR
FH116-2RH FRONT
WHEEL SPEED SENSOR LH REAR
WHEEL SPEED SENSOR RH REAR
WHEEL SPEED SENSOR STEERING ANGLE
SENSOR YAW RATE AND LATERAL
ACCELERATION SENSORS CLUSTER
CAN
B
B
VARIANT: All Vehicles
VIN RANGE: All
DATE OF ISSUE: May 2004
Page 82 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 05.2
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationCLUTCH PEDAL POSITION SENSOR CA287 6-WAY / BLACK TOP OF CLUTCH PEDAL
ELECTRONIC PARKING BRAKE SWITCH CA243 8-WAY / BLACK CENTER CONSOLE
FRONT ELECTRONIC MODULE CA24 26-WAY / NATURAL LH ‘A’ POST
CA31 20-WAY / BLACK
FH9 22-WAY / BLACK
FH59 12-WAY / BLACK
FH60 17-WAY / BLACK
NEUTRAL SWITCH (DIESEL) GB4 4-WAY / GREY TRANSMISSION, LH REAR
NEUTRAL SWITCH (GASOLINE) GB3 2-WAY / BLACK TRANSMISSION, LH REAR
PARKING BRAKE MODULE CA265 14-WAY / GREY LUGGAGE COMPARTMENT, RH REAR CA266 24-WAY / BLACK
PARKING BRAKE MOTOR CA269 6-WAY / GREY REAR SUSPENSION SUBFRAME
VARIABLE ASSIST STEERING ACTUATOR FH16 2-WAY / BLACK STEERING RACK PINION HOUSINGHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFH1 22-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
GB1 16-WAY / GREY / ENGINE HARNESS TO TRANSMISSION HARNESS ADJACENT TO TRANSMISSION BELL HOUSING
PI42 8-WAY / BLACK / ENGINE HARNESS TO FRONT HARNESS ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationCA141 UNDER LH FRONT SEAT
CA156 LUGGAGE COMPARTMENT, RH SIDE
FH77 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (FORWARD OF CA30)
PI40 (LHD) ENGINE COMPARTMENT, BEHIND RH WHEEL ARCH LINER
PI40 (RHD) ENGINE COMPARTMENT, BEHIND LH WHEEL ARCH LINER
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Parking Brake Module Pin Description and CharacteristicI CA265–3 IN-GEAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
SS CA265–5 SIGNAL SUPPLY VOLTAGE: NOMINAL 5 V
I CA265–6 CLUTCH PEDAL POSITION SENSOR FEEDBACK SIGNAL: VARIABLE VOLTAGE
O CA265–7 PARKING BRAKE MOTOR ENGAGE: ACTIVATE = B+
I CA265–10 PARKING BRAKE SWITCH – APPLY: CHANGE IN RESISTANCE
I CA265–11 PARKING BRAKE SWITCH – RELE ASE: CHANGE IN RESISTANCE
SS CA265–12 SIGNAL SUPPLY VOLTAGE: NOMINAL 5 V
SG CA265–13 SIGNAL GROUND: GROUND
O CA265–14 PARKING BRAKE MOTOR DISENGAGE: ACTIVATE = B+
B+ CA266–1 BATTERY POWER SUPPLY: B+
SG CA266–3 SIGNAL GROUND: GROUND
S CA266–4 SCP –
S CA266–5 SCP +
I CA266–10 PARKING BRAKE MOTOR POSITION SENSOR FEEDBACK SIGNAL: VARIABLE VOLTAGE
PG CA266–12 POWER GROUND: GROUND
PG CA266–13 POWER GROUND: GROUNDFront Electronic Module
Pin Description and CharacteristicS FH59–1 SCP –
S FH59–7 SCP +
PG FH59–12 POWER GROUND: GROUND
B+ FH60–1 SWITCHED SYSTEM POWER SUPPLY: B+
I FH60–2 VARIABLE ASSIST STEERING ACTUATOR RETURN: VARIABLE VOLTAGE
O FH60–9 VARIABLE ASSIST STEERING ACTUATOR DRIVE: B+ (PWM)
PG FH60–11 POWER GROUND: GROUND
PG FH60–13 POWER GROUND: GROUND
PG FH60–14 POWER GROUND: GROUND
PG FH60–15 POWER GROUND: GROUND
Page 84 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 05.3
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationDYNAMIC STABILITY CONTROL MODULE FH103 47-WAY / BLACK ENGINE COMPARTMENT, RH FRONT
ENGINE CONTROL MODULE PI1 134-WAY / BLACK FRONT BULKHEAD, P ASSENGER SIDE
FUEL / TRUNK RELEASE SWITCH PACK FC43 10-WAY / GREY INSTRUMENT PANEL
INSTRUMENT CLUSTER FC8 32-WAY / BLACK INSTRUMENT PANEL FC9 32-WAY / BLACK
SPEED CONTROL MODULE FC6 30-WAY / YELLOW INSTRUMENT PANEL, DRIVER SIDE
SPEED CONTROL SENSOR CC1 5-WAY / BLACK BELOW LH FRONT BUMPER
STEERING WHEEL — — STEERING WHEEL
TRANSMISSION CONTROL MODULE GB2 16-WAY / BLACK TRANSMISSION CONTROL VALVE ASSEMBLYHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFC4 14-WAY / GREEN / FASCIA HARNESS IN-LINE CONNECTOR BEHIND INSTRUMENT PANEL, LH SIDE
FC10 14-WAY / GREEN / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FC19 16-WAY / GREEN / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, LH SIDE
FC117 10-WAY / BLACK / STEERING WHEEL CASSETTE STEERING COLUMN
FH1 22-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH90 6-WAY / GREY / SPEED SENSOR LINK HARNESS TO FRONT HARNESS BELOW LH FRONT HEADLAMP ASSEMBLY
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationFC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH42 ENGINE COMPARTMENT, BEHIND RH HEADLAMP
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Speed Control Module Pin Description and CharacteristicO FC6–5 FORWARD ALERT SWITCH / INDICATOR DRIVE: FORWARD ALERT INDICATOR DRIVE
O FC6–6 CHIME MODULE DRIVE: CHIME ACTIVATE
C FC6–8 CAN –
C FC6–9 CAN +
PG FC6–12 POWER GROUND: GROUND
B+ FC6–14 IGNITION SWITCHED POWER SUPPLY: B+
B+ FC6–15 SWITCHED SYSTEM POWER SUPPLY: B+
I FC6–20 FORWARD ALERT SWITCH / INDICATOR DRIVE: MONITOR FORWARD ALERT SWITCH
C FC6–23 CAN –
C FC6–24 CAN +Dynamic Stability Control ModulePin Description and CharacteristicC FH103–11 CAN +
C FH103–12 CAN +
C FH103–14 CAN –
C FH103–15 CAN –Engine Control ModulePin Description and CharacteristicSS PI1–47 SPEED CONTROL SWITCH REQUEST: STEPPED RESISTANCE
I PI1–48 SPEED CONTROL SWITCHES SIGNAL GROUND: GROUND
C PI1–123 CAN –
C PI1–124 CAN +Instrument ClusterPin Description and CharacteristicC FC9–12 CAN +
C FC9–13 CAN –
C FC9–28 CAN +
C FC9–29 CAN –
Page 86 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 05.4
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationADAPTIVE DAMPING CONTROL MODULE CA11 16-WAY / BLUE LUGGAGE COMPARTMENT, REAR
CA12 16-WAY / GREY
DAMPER SOLENOID – LH FRONT FH117 2-WAY BLACK TOP OF LH FRONT DAMPER
DAMPER SOLENOID – LH REAR CA140 2-WAY BLACK TOP OF LH REAR DAMPER
DAMPER SOLENOID – RH FRONT FH118 2-WAY BLACK TOP OF RH FRONT DAMPER
DAMPER SOLENOID – RH REAR CA111 2-WAY BLACK TOP OF RH REAR DAMPER
DYNAMIC STABILITY CONTROL MODULE FH103 47-WAY / BLACK ENGINE COMPARTMENT, RH FRONT
INSTRUMENT CLUSTER FC8 32-WAY / BLACK INSTRUMENT PANEL FC9 32-WAY / BLACK
LATERAL ACCELEROMETER FH70 3-WAY / BLACK REARWARD OF FRONT BUMPER, LH SIDE
REAR ELECTRONIC MODULE CA63 17-WAY / BLACK LUGGAGE COMPARTMENT, RH REAR CA100 12-WAY / BLACK
CA101 20-WAY / BLACK
CA102 22-WAY / BLACK
CA103 26-WAY / NATURAL
VERTICAL ACCELEROMETER – FRONT FH63 3-WAY / BLACK REARWARD OF FRONT BUMPER, LH SIDE
VERTICAL ACCELEROMETER – REAR CA17 3-WAY / BLACK LUGGAGE COMPARTMENT, RH REARHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFH2 16-WAY / GREY / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH6 16-WAY GREEN / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST, ADJACENT TO FEMGROUNDS
Ground LocationCA158 LUGGAGE COMPARTMENT, LH SIDE REAR CORNER
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Adaptive Damping Control Module Pin Description and CharacteristicO CA11–1 RH REAR DAMPER SOLENOID DRIVE: PWM +
O CA11–2 RH REAR DAMPER SOLENOID DRIVE: PWM –
O CA11–3 LH REAR DAMPER SOLENOID DRIVE: PWM +
O CA11–4 LH REAR DAMPER SOLENOID DRIVE: PWM –
O CA11–5 LH FRONT DAMPER SOLENOID DRIVE: PWM –
O CA11–6 LH FRONT DAMPER SOLENOID DRIVE: PWM +
O CA11–7 RH FRONT DAMPER SOLENOID DRIVE: PWM –
O CA11–8 RH FRONT DAMPER SOLENOID DRIVE: PWM +
SG CA11–9 SIGNAL GROUND (INTERNALLY CONNECTED TO PIN 10): GROUND
PG CA11–10 POWER GROUND: GROUND
B+ CA11–12 IGNITION SWITCHED POWER SUPPLY (II): B+
S CA11–13 SCP –
S CA11–14 SCP +
B+ CA11–16 BATTERY POWER SUPPLY: B+
SS CA12–9 SENSOR SIGNAL SUPPLY VOLTAGE: NOMINAL 5 V
I CA12–10 REAR VERTICAL ACCELEROMETER SIGNAL: SENSOR SIGNAL
I CA12–11 LATERAL ACCELEROMETER SIGNAL: SENSOR SIGNAL
I CA12–12 FRONT VERTICAL ACCELEROMETER SIGNAL: SENSOR SIGNALDynamic Stability Control ModulePin Description and CharacteristicC FH103–11 CAN +
C FH103–12 CAN +
C FH103–14 CAN –
C FH103–15 CAN –Instrument ClusterPin Description and CharacteristicC FC9–12 CAN +
C FC9–13 CAN –
S FC9–25 SCP +
S FC9–26 SCP –
C FC9–28 CAN +
C FC9–29 CAN –Rear Electronic ModulePin Description and CharacteristicS CA102–1 SCP +
S CA102–2 SCP –
Page 87 of 200
Suspension Adaptive Damping
Jaguar S-TYPE 2005
Suspension Adaptive Damping
Fig. 05.4
13 4114
46 80
76 77 92
ll
15 45ll ll SS
81 118EE
Fig .01.1
Fig .01 .2 F
ig .01.3
Fig .01 .4
Fig . 01.5 F
ig . 01.6 F
ig .01 .7
Input
OutputI
O
B
P+Battery VoltagePower Ground Sensor/Signal Supply V
Sensor/Signal Ground Serial and Encoded Data
CAN
+
SCPC
S DD
–
D2B Network2
f05_4_200045
FC9-29 FC9-28
G Y
U Y
20.220.2
CA11-14
CA11-13
SS
SS
FC9-26 FC9-25
U Y
20.220.2
CA11-10
FH117-1
FH117-2FH118-1
FH118-2CA140-1
CA140-2CA111-1
CA111-2
CA11-2
BG
CA11-1
O
WB
CA11-4
BO
CA11-3
O
W
CA11-7
BG
CA11-8
O
WU
CA11-5
BW
CA11-6
O
WG
OOOO
BG WUBW WGBG WB BO W
BCA11-12
NG
CA11-16
NW
29
FH103-14 FH103-11
G Y
20.1
SS
CA102-2 CA102-1
U Y
20.220.2
FH6-12
FH6-13
FH2-9
FH2-10
FH70-2
WB
FH70-3
FH70-1
N Y
FH63-1
FH63-2
YR
FH63-3
N Y
CA17-1
CA17-2 CA17-3
YB N Y
I
CA11-9
N
CA12-9
Y
CA12-11
WB
CA12-12
YR
CA12-10
YB
II
FHS31
CAS54
41II
BB
CCCC
FH103-15 FH103-12
G Y
CC
FC9-13 FC9-12
G Y
CC
CAS53
FHS30
N
Y
FH6-8
FH6-2
FH6-10FH6-11
P
20.120.120.120.120.120.120.1
LH FRONT DAMPER SOLENOID
SYSTEM STATE
VEHICLE SPEED
DYNAMIC STABILITY CONTROL MODULE
INSTRUMENT CLUSTER
REAR ELECTRONIC MODULE
BRAKE ON / OFF
CA158
ADAPTIVE DAMPING CONTROL MODULE RH FRONT DAMPER SOLENOID
LH REAR DAMPER SOLENOID
RH REAR DAMPER SOLENOID
LATERAL ACCELEROMETER
FRONT VERTICAL ACCELEROMETER
REAR VERTICAL ACCELEROMETER
VARIANT: Adaptive Damping Vehicles
VIN RANGE: All
DATE OF ISSUE: May 2004
Page 88 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 05.5
NOTE: FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationFRONT LH TIRE PRESSURE SENSOR FRONT LH WHEEL
FRONT LH TPMS INITIATOR FH5 2-WAY / GREY FRONT LH WHEEL ARCH
FRONT RH TIRE PRESSURE SENSOR FRONT RH WHEEL
FRONT RH TPMS INITIATOR FH26 2-WAY / GREY FRONT RH WHEEL ARCH
REAR LH TIRE PRESSURE SENSOR REAR LH WHEEL
REAR LH TPMS INITIATOR RL4 2-WAY / GREY REAR LH WHEEL ARCH
REAR RH TIRE PRESSURE SENSOR REAR RH WHEEL
REAR RH TPMS INITIATOR RR4 2-WAY / GREY REAR RH WHEEL ARCH
SPARE TIRE PRESSURE SENSOR SPARE WHEEL
TIRE PRESSURE MONITORING SYSTEM MODULE CA146 16-WAY / BLUE LUGGAGE COMPARTMENT, RH REAR CA147 16-WAY / GREY
TIRE PRESSURE RECEIVER MODULE RF15 3-WAY / BLACK BELOW CENTER CONSOLEHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFH1 22-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS ADJACENT TO FRONT RH WHEEL ARCH
FH3 2-WAY GREY / LINK HARNESS ADJACENT TO FRONT LH WHEEL ARCH
RF34 16-WAY GREEN / ROOF HARNESS HEADLINER, CLOSE TO ROOF CONSOLE
RL2 8-WAY BLACK / LINK HARNESS ADJACENT TO REAR LH WHEEL ARCH
RR2 6-WAY GREY / LINK HARNESS ADJACENT TO REAR RH WHEEL ARCHGROUNDS
Ground LocationCA116 BEHIND REAR SEAT BACK, RH SIDE
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Tire Pressure Monitoring System Module
Pin Description and CharacteristicO CA146–5 REAR LH TPMS INITIATOR: RF 125kHz +
O CA146–6 REAR LH TPMS INITIATOR: RF 125kHz –
O CA146–7 REAR RH TPMS INITIATOR: RF 125kHz +
O CA146–8 REAR RH TPMS INITIATOR: RF 125kHz –
O CA146–13 FRONT LH TPMS INITIATOR: RF 125kHz +
O CA146–14 FRONT LH TPMS INITIATOR: RF 125kHz –
O CA146–15 FRONT RH TPMS INITIATOR: RF 125kHz +
O CA146–16 FRONT RH TPMS INITIATOR: RF 125kHz –
I CA147–4 TIRE PR ESSURE DATA:
B+ CA147–8 IGNITION SWITCHED POWER SUPPLY (II): B+
C CA147–10 CAN –
C CA147–11 CAN +
PG CA147–12 POWER GROUND: GROUND
B+ CA147–16 BATTERY POWER SUPPLY: B+Tire Pressure Receiver Module
Pin Description and CharacteristicO RF15–1 OUTPUT SIGNAL TO TPMS MODULE
PG RF15–2 POWER GROUND: GROUND
B+ RF15–3 BATTERY POWER SUPPLY: B+
Page 90 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 06.1
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAIR CONDITIONING CONTROL MODULE – PANEL FC27 26-WAY / GREY CENTER CONSOLE
FC28 22-WAY / GREY
AIR CONDITIONING CONTROL MODULE – REMOTE FC40 26-WAY / GREY BEHIND INSTRUMENT PANEL, RH SIDE (LHD), LH SIDE (RHD) FC41 22-WAY / GREY
AMBIENT TEMPERATURE SENSOR FH30 2-WAY / BLACK UNDER FRONT BUMPER, CENTER, FORWARD OF RADIATOR
AUXILIARY COOLANT PUMP (DIESEL) CP6 2-WAY / BLACK ENGINE COMPARTMENT, BEHIND RADIATOR, LH SIDE
AUXILIARY COOLANT PUMP (GASOLINE) CP4 2-WAY / BLACK ENGINE COMPARTMENT, BEHIND RADIATOR, LH SIDE
AUXILIARY COOLANT PUMP RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R7
BLOWER MOTOR AC2 6-WAY / BLACK UNDER INSTRUMENT PANEL, RH SIDE (LHD), LH SIDE (RHD)
BLOWER MOTOR RELAY — — REAR POWER DISTRIBUTION FUSE BOX – R7
DEFROST MODE ACTUATOR FC29 6-WAY / BLACK AIR DISTRIBUTION BOX
DISCHARGE TEMPERATURE SENSOR – EVAPORATOR AC5 2-WAY / GREY AIR DISTRIBUTION BOX
DISCHARGE TEMPERATURE SENSOR – LH FC20 2-WAY BLACK AIR DISTRIBUTION BOX
DISCHARGE TEMPERATURE SENSOR – RH FC30 2-WAY BLACK AIR DISTRIBUTION BOX
DUAL COOLANT CONTROL VALVE (DIESEL) FH34 3-WAY / BLACK ENGINE COMPARTMENT, RH SIDE, REARWARD OF RADIATOR
DUAL COOLANT CONTROL VALVE (GASOLINE) CP5 3-WAY / BLACK ENGINE COMPARTMENT, RH SIDE, REARWARD OF RADIATOR
DUAL SOLAR SENSOR SL1 6-WAY / BLACK INSTRUMENT PANEL GLARE SHIELD, FRONT CENTER
FLOOR MODE ACTUATOR FC21 6-WAY / BLACK AIR DISTRIBUTION BOX
FRESH / RECIRCULATION ACTUATOR AC3 6-WAY / BLACK BLOWER INTAKE
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
HUMIDITY SENSOR FC24 4-WAY / BLACK INSTRUMENT PANEL, ADJACENT TO STEERING COLUMN
IN-CAR TEMPERATURE SENSOR FC24 4-WAY / BLACK INSTRUMENT PANEL, ADJACENT TO STEERING COLUMN
LH WINDSHIELD HEATER CA122 1-WAY / BLACK CONNECTORS LOCATED IN LH UPPER ‘A’ POST
CA279 1-WAY / BLACK
LH WINDSHIELD HEATER RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R17
PANEL MODE ACTUATOR FC22 6-WAY / BLACK AIR DISTRIBUTION BOX
REAR POWER DISTRIBUTION FUSE BOX — — LUGGAGE COMPARTMENT
WIPER PARK HEATER / RH WINDSHIELD HEATER RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R21
WIPER PARK HEATER OR RH WINDSHIELD HEATER CA65 1-WAY / BLACK CONNECTORS LOCATED IN RH UPPER ‘A’ POST CA71 1-WAY / BLACKHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationAC7 2-WAY / GREY / CABIN HARNESS TO CLIMATE CONTROL HARNESS BEHIND PASSENGER AIRBAG
CP1 10-WAY / BLACK / INTERCOOLER PUMP LINK LEAD ENGINE COMPARTMENT, RH FRONT, ADJACENT TO RADIATOR
CP7 4-WAY / BLACK / COOLANT PUMP LINK LEAD ENGINE COMPARTMENT, RH FRONT, ADJACENT TO RADIATOR
FC4 14-WAY / GREEN / FASCIA HARNESS IN-LINE CONNECTOR BEHIND INSTRUMENT PANEL, LH SIDE
FC10 14-WAY / GREEN / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FC33 16-WAY / GREEN / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FC34 16-WAY / GREEN / FASCIA HARNESS IN-LINE CONNECTOR ADJACENT TO BLOWER MOTOR
FH82 2-WAY / GREY / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST
FH114 2-WAY / GREY / FRONT HARNESS TO CABIN HARNESS BEHIND INSTRUMENT PANEL, LH SIDE
SL3 10-WAY / GREY / FASCIA HARNESS TO SOLAR SENSOR LINK BEHIND INSTRUMENT PANEL, RH SIDEGROUNDS
Ground LocationCA30 LH LOWER ‘A’ POST, ADJACENT TO THE GENERAL ELECTRONIC CONTROL MODULE (REARWARD OF FH77)
CA50 RH LOWER ‘A’ POST, BELOW PRIMARY JUNCTION FUSE BOX
FC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH42 ENGINE COMPARTMENT, BEHIND RH HEADLAMP
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Air Conditioning Control Module – Panel Pin Description and CharacteristicI FC27–1 DEFROST MODE ACTUATOR POSITION FEEDBACK: VARIABLE VOLTAGE
I FC27–3 PANEL MODE ACTUATOR POSITION FEEDBACK: VARIABLE VOLTAGE
I FC27–4 HUMIDITY SENSOR SIGNAL: VARIABLE VOLTAGE
O FC27–5 DRIVER SIDE DUAL COOLANT CONTROL VALVE CONTROL DRIVE: ACTIVATE = GROUND (PWM)
O FC27–6 PASSENGER SIDE DUAL COOLANT CONTROL VALVE CONTROL DRIVE: ACTIVATE = GROUND (PWM)
SS FC27–7 HUMIDITY SENSOR SIGNAL SUPPLY VOLTAGE: NOMINAL 5 V
O FC27–9 FRESH / RECIRCULATION ACTUATOR DRIVE – CLOSE: ACTIVATE = B+
O FC27–10 FRESH / RECIRCULATION ACTUATOR DRIVE – OPEN: ACTIVATE = B+
O FC27–13 DEFROST MODE ACTUATOR DRIVE – OPEN: ACTIVATE = B+
SG FC27–14 IN-CAR TEMPERATURE SENSOR SIGNAL GROUND: GROUND
I FC27–15 FRESH / RECIRCULATION ACTUATOR POSITION FEEDBACK: VARIABLE VOLTAGE
I FC27–16 FLOOR MODE ACTUATOR POSITION FEEDBACK: VARIABLE VOLTAGE
SG FC27–17 ACTUATOR SIGNAL GROUND: GROUND
O FC27–18 AUXILIARY COOLANT PUMP RELAY ACTIVATE: TO ACTIVATE, A/CCM SWITCHES CIRCUIT TO GROUND
O FC27–19 BLOWER MOTOR RELAY ACTIVATE: TO ACTIVATE, A/CCM SWITCHES CIRCUIT TO GROUND
O FC27–20 HEATED WIPER PARK OR HEATED WINDSHIELD RELAY(S) ACTIVATE: TO ACTIVATE, A/CCM SWITCHES CIRCUIT TO GROUND
O FC27–21 BLOWER MOTOR CONTROL: B+ (PWM)
O FC27–22 FLOOR MODE ACTUATOR DRIVE – OPEN: ACTIVATE = B+
O FC27–23 FLOOR MODE ACTUATOR DRIVE – CLOSE: ACTIVATE = B+
O FC27–24 PANEL MODE ACTUATOR DRIVE – OPEN: ACTIVATE = B+
O FC27–25 PANEL MODE ACTUATOR DRIVE – CLOSE: ACTIVATE = B+
O FC27–26 DEFROST MODE ACTUATOR DRIVE – CLOSE: ACTIVATE = B+
C FC28–1 CAN –
PG FC28–2 POWER GROUND: GROUND
B+ FC28–3 IGNITION SWITCHED POWER SUPPLY (II): B+
I FC28–5 BLOWER MOTOR CONTROL FEEDBACK: VARIABLE FREQUENCY
I FC28–6 PASSENGER SIDE DISCHARGE TEMPERATURE SENSOR SIGNAL: NTC SENSOR / VOLTAGE DECREASES AS TEMPERATURE INCREASES
I FC28–7 DUAL SOLAR SENSOR SIGNAL – LH: VOLTAGE DECREASES AS LIGHT INCREASES
SG FC28–8 AMBIENT TEMPERATURE SENSOR SIGNAL GROUND: GROUND
I FC28–9 IN-CAR TEMPERATURE SENSOR SIGNAL: NTC SENSOR / VOLTAGE DECREASES AS TEMPERATURE INCREASES
I FC28–10 EVAPORATOR DISCHARGE TEMPERATURE SENSOR SIGNAL: NTC SENSOR / VOLTAGE DECREASES AS TEMPERATURE INCREASES
SG FC28–11 ACTUATORS SIGNAL GROUND: GROUND
C FC28–12 CAN
B+ FC28–14 BATTERY POWER SUPPLY: B+
I FC28–15 PANEL ILLUMINATION (DIMMER-CONTROLLED): B+ (PWM)
SG FC28–16 EVAPORATOR DISCHARGE TEMPERATURE SENSOR SIGNAL GROUND: GROUND
I FC28–17 AMBIENT TEMPERATURE SENSOR SIGNAL: NTC SENSOR / VOLTAGE DECR EASES AS TEMPERATURE INCREASES
I FC28–18 DRIVER SIDE DISCHARGE TEMPERATURE SENSOR SIGNAL: NTC SENSOR / VOLTAGE DECREA SES AS TEMPERATURE INCREASES
SG FC28–19 LH / RH DISCHARGE TEMPERATURE SENSORS SIGNAL GROUND: GROUND
I FC28–20 DUAL SOLAR SENSOR SIGNAL – RH: VOLTAGE DECREASES AS LIGHT INCREASES
SS FC28–22 ACTUATORS SIGNAL SUPPLY VOLTAGE: NOMINAL 5 VAir Conditioning Control Module – Remote
Pin Description and CharacteristicI FC40–1 DEFROST MODE ACTUATOR POSITION FEEDBACK: VARIABLE VOLTAGE
I FC40–3 PANEL MODE ACTUATOR POSITION FEEDBACK: VARIABLE VOLTAGE
I FC40–4 HUMIDITY SENSOR SIGNAL: VARIABLE VOLTAGE
O FC40–5 DRIVER SIDE DUAL COOLANT CONTROL VALVE CONTROL DRIVE: ACTIVATE = GROUND (PWM)
O FC40–6 PASSENGER SIDE DUAL COOLANT CONTROL VALVE CONTROL DRIVE: ACTIVATE = GROUND (PWM)
SS FC40–7 HUMIDITY SENSOR SIGNAL SUPPLY VOLTAGE: NOMINAL 5 V
O FC40–9 FRESH / RECIRCULATION ACTUATOR DRIVE – CLOSE: ACTIVATE = B+
O FC40–10 FRESH / RECIRCULATION ACTUATOR DRIVE – OPEN: ACTIVATE = B+
O FC40–13 DEFROST MODE ACTUATOR DRIVE – OPEN: ACTIVATE = B+
SG FC40–14 IN-CAR TEMPERATURE SENSOR SIGNAL GROUND: GROUND
I FC40–15 FRESH / RECIRCULATION ACTUATOR POSITION FEEDBACK: VARIABLE VOLTAGE
I FC40–16 FLOOR MODE ACTUATOR POSITION FEEDBACK: VARIABLE VOLTAGE
SG FC40–17 ACTUATOR SIGNAL GROUND: GROUND
O FC40–18 AUXILIARY COOLANT PUMP RELAY ACTIVATE: TO ACTIVATE, A/CCM SWITCHES CIRCUIT TO GROUND
O FC40–19 BLOWER MOTOR RELAY ACTIVATE: TO ACTIVATE, A/CCM SWITCHES CIRCUIT TO GROUND
O FC40–20 HEATED WIPER PARK OR HEATED WINDSHIELD RELAY(S) ACTIVATE: TO ACTIVATE, A/CCM SWITCHES CIRCUIT TO GROUND
O FC40–21 BLOWER MOTOR CONTROL: B+ (PWM)
O FC40–22 FLOOR MODE ACTUATOR DRIVE – OPEN: ACTIVATE = B+
O FC40–23 FLOOR MODE ACTUATOR DRIVE – CLOSE: ACTIVATE = B+
O FC40–24 PANEL MODE ACTUATOR DRIVE – OPEN: ACTIVATE = B+
O FC40–25 PANEL MODE ACTUATOR DRIVE – CLOSE: ACTIVATE = B+
O FC40–26 DEFROST MODE ACTUATOR DRIVE – CLOSE: ACTIVATE = B+
C FC41–1 CAN –
PG FC41–2 POWER GROUND: GROUND
B+ FC41–3 IGNITION SWITCHED POWER SUPPLY (II): B+
I FC41–5 BLOWER MOTOR CONTROL FEEDBACK: VARIABLE FREQUENCY
I FC41–6 PASSENGER SIDE DISCHARGE TEMPERATURE SENSOR SIGNAL: NTC SENSOR / VOLTAGE DECREASES AS TEMPERATURE INCREASES
I FC41–7 DUAL SOLAR SENSOR SIGNAL – LH: VOLTAGE DECREASES AS LIGHT INCREASES
SG FC41–8 AMBIENT TEMPERATURE SENSOR SIGNAL GROUND: GROUND
I FC41–9 IN-CAR TEMPERATURE SENSOR SIGNAL: NTC SENSOR / VOLTAGE DECREASES AS TEMPERATURE INCREASES
I FC41–10 EVAPORATOR DISCHARGE TEMPERATURE SENSOR SIGNAL: NTC SENSOR / VOLTAGE DECREASES AS TEMPERATURE INCREASES
SG FC41–11 ACTUATORS SIGNAL GROUND: GROUND
C FC41–12 CAN +
B+ FC41–14 BATTERY POWER SUPPLY: B+
SG FC41–16 EVAPORATOR DISCHARGE TEMPERATURE SENSOR SIGNAL GROUND: GROUND
I FC41–17 AMBIENT TEMPERATURE SENSOR SIGNAL: NTC SENSOR / VOLTAGE DECR EASES AS TEMPERATURE INCREASES
I FC41–18 DRIVER SIDE DISCHARGE TEMPERATURE SENSOR SIGNAL: NTC SENSOR / VOLTAGE DECREA SES AS TEMPERATURE INCREASES
SG FC41–19 LH / RH DISCHARGE TEMPERATURE SENSORS SIGNAL GROUND: GROUND
I FC41–20 DUAL SOLAR SENSOR SIGNAL – RH: VOLTAGE DECREASES AS LIGHT INCREASES
SS FC41–22 ACTUATORS SIGNAL SUPPLY VOLTAGE: NOMINAL 5 V
Page 91 of 200
Climate Control System; Windshield Heaters
Jaguar S-TYPE 2005
Climate Control System; Windshield Heaters
Fig. 06.1
13 4114
46 80
76 77 92
ll
15 45ll ll SS
81 118EE
Fig .01.1
Fig .01 .2 F
ig .01.3
Fig .01 .4
Fig . 01.5 F
ig . 01.6 F
ig .01 .7
Input
OutputI
O
B
P+Battery VoltagePower Ground Sensor/Signal Supply V
Sensor/Signal Ground Serial and Encoded Data
CAN
+
SCPC
S DD
–
D2B Network2
f06_1_200045
RW
B NG NW
NW
FC40 / 27-01FC40 / 27-03FC40 / 27-05
FC41/28-12FC41/28-14FC41/28-01FC41/28-03
FC40 / 27-06FC40 / 27-09FC40 / 27-10FC40 / 27-17FC40 / 27-18FC40 / 27-19FC40 / 27-22FC40 / 27-23FC40 / 27-20FC40 / 27-24FC40 / 27-26FC41 / 28-02FC40 / 27-25FC41 / 28-05FC41 / 28-07FC41 / 28-09FC41 / 28-06FC41 / 28-10
WU
NWWRWB (LHD)NGB YBY WYU WUNRBGNGNRWUWRNRWBWR YRNG NWWWB
FC40 / 27-13FC40 / 27-15FC40 / 27-16FC40 / 27-14
G Y
NR
NR
88
FC41 / 28-11
FC28-15
FC41 / 28-17FC41 / 28-16FC41 / 28-19
WU NR
UY
NWR
FC41 / 28-22FC41 / 28-08FC41 / 28-20
YGWNG
FC41 / 28-18
WG (LHD)
FC41 / 28-06
WG (RHD)
FC41 / 28-18
WB (RHD)
40II
FC40 / 27-04
WG
FC40 / 27-07
NG
FC40 / 27-21
WU
NG
NG WG WR
GW
NW WB
FC24
-1 FC24
-3WU NR
AC5-2 AC5
-1WR NR
FH30 -1 FH30
-2WU NW
AC3
-1
AC3-6
AC3
-3
AC3 -4 AC3
-5
YR
WR WR YR NR
FC29
-1
FC29-6
FC29-3
FC29-4 FC29
-5
YB
WB
WB
YB NW
FC22
-1
FC22-6
FC22-3
FC22 -4 FC22
-5
Y
W
W
YN
FC21
-6
FC21-1
FC21 -3
FC21-5 FC21
-4
YU
WU WU
YU NW
LH RH
FC24
-2 FC24
-4NG WG
WU
NGWU
FC34
-3 FC34
-7
FC4-1 FC4
-8
FC34 -6 FC34
-15 FC34
-14
FC34 -4NR
FC34-11YRFCS23
FCS32
CAN
FC4 -9
FC4
-10
70
†CP34-3
*CP5-3*CP1 -2
*CP1 -3 *CP1
-1†CP34-2
*CP5-2 †CP34-1
*CP5-1
NW
NW Y NG
NG
6364677268
N
N
Y
Y
NR
NR
RU
3
1
5
2
R21
4
3
1
5
2
R7
4
NG RW
NG
NG
1213
BG
R
3
1
5
2
R7
4
R
B
AC2
-3 AC2
-6
WU
FC34 -5 FC34
-12 FC33
-5
CA50
(CA30)
CA279-1
CA122-1
RW
B
CA30
CA65-1
CA71-1
RU
BCA50
3
1
5
2
R17
4
FC10
-5
B*CP4-2†CP6-2
*CP4-1†CP6-1
RW
*CP1-4
†CP7-2
FH42B
FC10 -9
FC38
LH DISCHARGE
TEMPERATURE SENSOR RH DISCHARGE
TEMPERATURE SENSOR DUAL
SOLAR
SENSOR HUMIDITY
SENSOR
IN-CAR
TEMPERATURE SENSOR AMBIENT
TEMPERATURE SENSOR FRESH / RECIRCULATION
ACTUATOR DEFROST MODE
ACTUATOR PANEL MODE
ACTUATOR FLOOR MODE
ACTUATOR
EVAPORATOR
DISCHARGE
TEMPERATURE SENSORFC20
-1 FC20
-2 FC30
-1 FC30
-2 SL1
-1 SL1
-5 SL1
-6
SL1
-2
AIR CONDITIONING CONTROL MODULE
DUAL COOLANT CONTROL VALVE BLOWER MOTOR BLOWER MOTOR
RELAY AUXILIARY
COOLANT PUMP*
AUXILIARY COOLANT PUMPRELAY*
INSTRUMENT CLUSTER:
AUTO HEADLAMPS
INSTRUMENT CLUSTER: GROUND
REFER TO APPENDIX
CAN / A/CCM MESSAGES
DIMMER CONTROLLED LIGHTING:
PANEL ILLUMINATION -
CONTROL PANEL ONLY.
NOTE: Mirror Heaters and Heated Rear
Window controlled via A/CCM / CAN / SCP /
FEM / DDM. Refer to Fig. 10.2.
NOTE: Remote A/CCM (navigation): FC40 / FC41;
A/CCM with control panel: FC27 / FC28.
Connector numbers are shown as FC40 / 27 and FC41 / 28.
NOTE: For Air Conditioning Compressor and Refrigerent Pressure Sensor circuits;
refer to Figures 03.2, 03.4, 03.6 or 03.8 . NOTE:
* V8 only; † Diesel only
08.3 08.2 08.1
08.3 08.2
09.2
20.1
20.1 08.1
REAR POWER DISTRIBUTION FUSE BOX
FRONT POWER DISTRIBUTION FUSE BOX
LH WINDSHIELD HEATER
LH WINDSHIELD HEATERRELAY
WIPER PARK HEATER OR
RH WINDSHIELD HEATER WIPERPARKHEATER/
RH WINDSHIELD HEATER RELAY
IIIOOOOOI
ICC
IIIIIIIIIIIIOOOOOOOOOP
B
+B+
AC7-1
DRIVER PASSENGER AC2-1
AC7-2
*CP1-5
†CP7-1 FH114-1
FH82-1
SL3
-8 SL3
-3 SL3
-6 SL3
-2
FCS31
NOTE:
* Gasoline only;
† Diesel only
VARIANT: All Vehicles
VIN RANGE: All
DATE OF ISSUE: May 2004