2005 JAGUAR S TYPE transmission
[x] Cancel search: transmissionPage 76 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 04.1
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationIGNITION SWITCH FC18 7-WAY / BLACK STEERING COLUMN COWLING
J-GATE MODULE CA245 16-WAY / BLACK J-GATE ASSEMBLY
TRANSMISSION CAPACITOR (V6) GB17 2-WAY / BLACK ENGINE COMPARTMENT, BULKHEAD
TRANSMISSION CAPACITOR (V8) PI59 2-WAY / BLACK ENGINE COMPARTMENT, BULKHEAD
TRANSMISSION CONTROL MODULE GB2 16-WAY / BLACK TRANSMISSION CONTROL VALVE ASSEMBLYHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFC26 16-WAY / BLUE / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, DRIVER SIDE
GB1 16-WAY / GREY / ENGINE HARNESS TO TRANSMISSION HARNESS ADJACENT TO TRANSMISSION BELL HOUSING
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationCA154 UNDER LH FRONT SEAT
FH4 ENGINE COMPARTMENT, REARWARD OF RH WHEEL ARCH
PI40 (LHD) ENGINE COMPARTMENT, BEHIND RH WHEEL ARCH LINER
PI40 (RHD) ENGINE COMPARTMENT, BEHIND LH WHEEL ARCH LINER
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Transmission Control Module Pin Description and CharacteristicC GB2–2 CAN –
D GB2–3 SERIAL COMMUNICATION
C GB2–6 CAN +
B+ GB2–9 IGNITION SWITCHED POWER SUPPLY: B+
O GB2–10 PARK / NEUTRAL SIGNAL: GROUND WHEN ACTIVATED
PG GB2–13 POWER GROUND: GROUND
B+ GB2–14 BATTERY POWER SUPPLY: B+
PG GB2–16 POWER GROUND: GROUND
Page 77 of 200
Transmission (Automatic)
Jaguar S-TYPE 2005
Transmission (Automatic)
Fig. 04.1
13 4114
46 80
76 77 92
ll
15 45ll ll SS
81 118EE
Fig .01.1
Fig .01 .2 F
ig .01.3
Fig .01 .4
Fig . 01.5 F
ig . 01.6 F
ig .01 .7
Input
OutputI
O
B
P+Battery VoltagePower Ground Sensor/Signal Supply V
Sensor/Signal Ground Serial and Encoded Data
CAN
+
SCPC
S DD
–
D2B Network2
f04_1_200045
CA245-11CA245-9
GB2-14
CA245-10
GB2-9GB2-10
B Y
G Y
GR
GR GO
NR
GB1-6
GB2-6
GB2-2
CA245-4
CA245-2
BB
74
19II
GR
03.1
03.3
03.5
03.7
02.1
02.2
02.3
PI40AL
PP
PIS30
B
GB2-16
B
GB2-13
B
CC
20.120.1
O
GB2-3
D
20.2
G Y
G Y
CCCC
CA245-1
GO
CA245-3
UY
P
R
N
D
2
3
CA154
NR
FC18-4
YFC18-3
IOO
7
09.2
17II
B
20.120.120.121.1
CA245-12
P
Y
FC26-4FCS25
Y
07.1
O
CAN
P
R
N
D 5
4
3
45
GB2-9
GO
B
18II
V6
V8
V6
V8
GB1-8
NR
NR
GBS4
GB17-1GB17-2
NR
PI40AL
PP
GB1-9
GB1-10
PIS30B
B
B
B
B
GB2-16
B
GB2-13
BGBS3
B
B
GB2-14
NR
B
75
NR
PIS54
PI59-1PI59-2
NR
B
PIS53B V6
V8
1 2 3
4
5 6
IIIIIIIOOOOOOO
ECM: PARK, NEUTRAL (CIRCUIT CONTINUED)
NOTE
: GB1-6
– V6 and Diesel only.
PI41-6
– Diesel only.
CAPACITOR (V6)
CAPACITOR (V8)
IGNITION SWITCHKEY LOCK
SOLENOID
GEARSHIFT
INTERLOCK SOLENOID
NOT-IN-PARK SWITCH
MODE
SWITCH
J GATE ASSEMBLY
AUTOMATIC TRANSMISSION
TRANSMISSION
CONTROL MODULE
SHIFT
SOLENOID
TCC PRESSURE
REGULATOR
SOLENOID
PRESSURE REGULATOR
SOLENOIDS
FLUID TEMPERATURE
SENSOR TURBINE SPEED
SENSOR
OUTPUT SPEED
SENSOR
GEAR POSITION
SWITCH
REFER TO APPENDIX
TCM / CAN MESSAGES
GEAR SELECTOR AND
MODE SWITCH ILLUMINATION
KEY-IN AUDIBLE WARNING
(CIRCUIT CONTINUED)
CAN MESSAGES:
• GEAR SELECTOR
POSITIONS 2 3 4 5
•BRAKEON/OFF
CAS16
FH4-1 PI41-8
PI41-7
Note:
Diesel only
PI41-6
SERIAL
COMMUNICATION
VARIANT: Automatic Vehicles
VIN RANGE: All
DATE OF ISSUE: May 2004
Page 78 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 04.2
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationCLUTCH CANCEL SWITCH CA285 (RHD) 2-WAY / BLACK TOP OF CLUTCH PEDAL (TOP SWITCH)
CA291 (LHD) 5-WAY / BLACK
CLUTCH PEDAL POSITION SENSOR CA287 6-WAY / BLACK TOP OF CLUTCH PEDAL
CLUTCH PEDAL SAFETY SWITCH CA286 2-WAY / BLACK TOP OF CLUTCH PEDAL (BOTTOM SWITCH)
ENGINE CONTROL MODULE PI1 134-WAY / BLACK FRONT BULKHEAD, P ASSENGER SIDE
NEUTRAL SWITCH (DIESEL) GB4 4-WAY / GREY TRANSMISSION, LH REAR
NEUTRAL SWITCH (GASOLINE) GB3 2-WAY / BLACK TRANSMISSION, LH REAR
PARKING BRAKE MODULE CA265 14-WAY / GREY LUGGAGE COMPARTMENT, RH REAR CA266 24-WAY / BLACK
POWERTRAIN CONTROL MODULE C98 48-WAY / BROWN FRONT BULKHEAD, PASSENGER SIDE C99 48-WAY / GREY
FH13 48-WAY / BLACK
REVERSE SWITCH GB5 2-WAY / BLACK TRANSMISSION, LH REARHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFH1 20-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH2 16-WAY / GREY / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH3 16-WAY / BLUE / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST
GB1 16-WAY / GREY / ENGINE HARNESS TO TRANSMISSION HARNESS ADJACENT TO TRANSMISSION BELL HOUSING
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDE
PI42 8-WAY / BLACK / ENGINE HARNESS TO FRONT HARNESS ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationFH4 ENGINE COMPARTMENT, REARWARD OF RH WHEEL ARCH
PI40 (LHD) ENGINE COMPARTMENT, BEHIND RH WHEEL ARCH LINER
PI40 (RHD) ENGINE COMPARTMENT, BEHIND LH WHEEL ARCH LINER
Parking Brake Module Pin Description and CharacteristicI CA265–3 IN-GEAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
SS CA265–5 CLUTCH PEDAL POSITION SENSOR SUPPLY VOLTAGE: NOMINAL 5 V
I CA265–6 CLUTCH PEDAL POSITION SENSOR FEEDBACK SIGNAL: VARIABLE VOLTAGE
SG CA266–3 CLUTCH PEDAL POSITION SENSOR GROUND: GROUND
I CA266–15 IN-GEAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUNDEngine Control Module (Gasoline)Pin Description and CharacteristicI PI1–31 AUTOMATIC – PARK / NEUTRAL SIGNAL: B+ WHEN ACTIVATED MANUAL, ROW – PARK / NEUTRAL SIGNAL: B+ WHEN IGNITION CRANK (III)
MANUAL, NAS – CLUTCH PEDAL SAFETY SWITCH (PARK / NEUTRAL SIGNAL): B+ WHEN ACTIVATED
I PI1–33 CLUTCH CANCEL SWITCH: NORMALLY CLOSED / GROUND WHEN ACTIVATEDPowertrain Control Module (Diesel)
Pin Description and CharacteristicI FH13–G3 CLUTCH CANCEL SWITCH: NORMALLY CLOSED / GROUND WHEN ACTIVATED
Page 79 of 200
Transmission (Manual)
Jaguar S-TYPE 2005
Transmission (Manual)
Fig. 04.2
13 4114
46 80
76 77 92
ll
15 45ll ll SS
81 118EE
Fig .01.1
Fig .01 .2 F
ig .01.3
Fig .01 .4
Fig . 01.5 F
ig . 01.6 F
ig .01 .7
Input
OutputI
O
B
P+Battery VoltagePower Ground Sensor/Signal Supply V
Sensor/Signal Ground Serial and Encoded Data
CAN
+
SCPC
S DD
–
D2B Network2
f04_2_200045
PI42-8
GR
FH3-10
PI1-031
GB1-13
WG
PI1-033
CA285-2 -1 (RHD)
WG
NR
FH3-2
PI41-4
WG
GR
GB1-6
GR
91
B
GB5-2
GB5-1
PIS30
B
PI40AL
GB
GB1-9
B
BB
08.3
II
GR
CA291-3 -1 (LHD)
CA286 -2 -1
GR
NR92
ENGINE CONTROL
MODULE
(GASOLINE)
CLUTCH CANCELSWITCH REVERSE
SWITCH
CLUTCH PEDAL
SAFETY SWITCH (NAS ONLY)
* NOTE : Early production vehicles - feature not enabled.
WG
FH13-G3
CA285-2 -1 (RHD)
WG
NR
FH3-2
91
I
CA291-3 -1 (LHD)
POWERTRAIN
CONTROL MODULE (DIESEL)
CLUTCH CANCELSWITCH
FH4-1
PI41-7
(Diesel only)
REVERSE
LAMPS
GB1-11
R
CA287-1 CA287-2
I
G
CA287-3
CA266-3
CA265-5 CA265-6
YG
I
YG
YG
YG
CA265-3
CA287-3
CA265-5
I
CA266-15
NEUTRAL SWITCH (DIESEL)
FH1-13
R
PI41-23
GB4-2
FH2-6
GB3-2
GB3-1 PI42-5
GB1-12
FH1-2
NEUTRAL SWITCH (GASOLINE)
GB1-16
PI41-27
GBGB GB
GB
CLUTCH PEDAL POSITION SENSOR *
GB1-13
RR
GB
GB4-4
PI41-35
GB1-16
GB GB
YG
GB4-1
GB1-15
PI41-12
YGYG
RN
CAS90
(Gasoline only)
(Diesel only)
CAS89 CAS86
CAU5
BRD
PARKING BRAKE MODULE
VARIANT:
Manual Vehicles
VIN RANGE: All
DATE OF ISSUE: May 2004
Page 80 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 05.1
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationACTIVE BRAKE BOOSTER — — ENGINE COMPARTMENT BULKHEAD, DRIVER SIDE
ACTIVE BRAKE BOOSTER SOLENOID FH56 6-WAY / BLACK ENGINE COMPARTMENT, BRAKE BOOSTER
BRAKE FLUID RESERVOIR FH104 2-WAY / BLACK BRAKE BOOSTER
BRAKE PRESSURE SENSOR FH54 3-WAY / BLACK BRAKE MASTER CYLINDER, UNDERSIDE
CENTER CONSOLE SWITCH PACK FC113 8-WAY / BLACK CENTER CONSOLE
FC119 8-WAY / BLACK
DYNAMIC STABILITY CONTROL MODULE FH103 47-WAY / BLACK ENGINE COMPARTMENT, RH FRONT
PEDAL FORCE SWITCH FH56 6-WAY / BLACK ENGINE COMPARTMENT, BRAKE BOOSTER
PEDAL TRAVEL SENSOR FH11 3-WAY / BLACK ENGINE COMPARTMENT, BRAKE BOOSTER
STEERING ANGLE SENSOR FC110 4-WAY / GREY STEERING COLUMN
WHEEL SPEED SENSOR – LH FRONT FH115 2-WAY / BLACK LH FRONT WHEEL HUB
WHEEL SPEED SENSOR – LH REAR RL1 2-WAY / BLACK LH REAR WHEEL HUB
WHEEL SPEED SENSOR – RH FRONT FH116 2-WAY / BLACK RH FRONT WHEEL HUB
WHEEL SPEED SENSOR – RH REAR RR1 2-WAY / BLACK RH REAR WHEEL HUB
YAW RATE AND LATERAL ACCELERATION SENSORS CLUSTER CA236 6-WAY / BLACK UNDER CENTER CONSOLEHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFC10 14-WAY / GREEN / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FC26 16-WAY / BLUE / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, DRIVER SIDE
FH1 22-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH2 16-WAY / GREY / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH6 16-WAY GREEN / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST, ADJACENT TO FEM
RL2 2-WAY / BLACK / LH REAR LINK REAR SUSPENSION SUBFRAME RH SIDE
RR2 2-WAY / BLACK / RH REAR LINK REAR SUSPENSION SUBFRAME RH SIDEGROUNDS
Ground LocationFC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH42 ENGINE COMPARTMENT, BEHIND RH HEADLAMP
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Dynamic Stability Control Module
Pin Description and CharacteristicB+ FH103–1 BATTERY POWER SUPPLY – PUMP: B+
— FH103–3 STEERING ANGLE SENSOR SIGNAL (A): PULSED SIGNAL
B+ FH103–4 IGNITION SWITCHED POWER SUPPLY (II): B+
SG FH103–5 SENSOR GROUND – YAW RATE, STEERING ANGLE SENSORS: GROUND
I FH103–6 STEERING ANGLE SENSOR SIGNAL (B): PULSED SIGNAL
SS FH103–7 YAW RATE, STEERING ANGLE SENSORS SUPPLY VOLTAGE: B+
SG FH103–8 BRAKE FLUID LEVEL SENSOR SIGNAL GROUND: GROUND
I FH103–9 BRAKE FLUID LEVEL SENSOR SIGNAL: BRAKE FLUID LEVEL LOW = GROUND
C FH103–11 CAN +
C FH103–12 CAN +
O FH103–13 VEHICLE SPEED SIGNAL (SLIDING ROOF THRESHOLD): < 62 KM/H (38.5 MPH) = GROUND; > 62 KM/H (38.5 MPH) = B+
C FH103–14 CAN –
C FH103–15 CAN –
PG FH103–16 POWER GROUND – VALVES: GROUND
SS FH103–17 ACTIVE BRAKE BOOSTER SOLENOID SUPPLY VOLTAGE: NOMINAL 5 V
SS FH103–18 BRAKE PRESSURE SENSOR SUPPLY VOLTAGE: NOMINAL 5 V
SG FH103–19 SENSOR GROUND – BRAKE PRESSURE SENSOR: GROUND
I FH103–20 BRAKE PRESSURE SENSOR SIGNAL, NOMINAL 0.5 – 4.5 V: VOLTAGE INCREASES AS PRESSURE INCREASES
SG FH103–24 ACTIVE BRAKE BOOSTER TRAVEL SENSOR SIGNAL GROUND: GROUND
C FH103–25 CAN – (LOCAL)
SS FH103–26 ACTIVE BRAKE BOOSTER TRAVEL SENSOR SUPPLY VOLTAGE: NOMINAL 5 V
SS FH103–27 ACTIVE BRAKE BOOSTER FORCE SWITCH NORMALLY OPEN (NOMINAL 5 V): OPEN / CLOSED CIRCUIT
I FH103–28 ACTIVE BRAKE BOOSTER FORCE SWITCH SIGNAL: GROUND
C FH103–29 CAN + (LOCAL)
SS FH103–30 ACTIVE BRAKE BOOSTER FORCE SWITCH NORMALLY CLOSED (NOMINAL 5 V): CLOSED / OPEN CIRCUIT
O FH103–31 ACTIVE BRAKE BOOSTER SOLENOID DRIVE: GROUND (PWM)
B+ FH103–32 BATTERY POWER SUPPLY – VALVES: B+
SG FH103–33 RH FRONT WHEEL SPEED SENSOR SIGNAL GROUND: GROUND
I FH103–34 RH FRONT WHEEL SPEED SENSOR SIGNAL: 46 PULSES PER WHEEL REVOLUTION
I FH103–36 LH REAR WHEEL SPEED SENSOR SIGNAL: 46 PULSES PER WHEEL REVOLUTION
SG FH103–37 LH REAR WHEEL SPEED SENSOR SIGNAL GROUND: GROUND
I FH103–38 DYNAMIC STABILITY CONTROL SWITCH: NORMALLY OPEN / GROUND WHEN ACTIVATED
I FH103–40 ACTIVE BRAKE BOOSTER TRAVEL SENSOR SIGNAL, NOMINAL 0.5 – 4.5 V: VARIABLE VOLTAGE
SG FH103–42 RH REAR WHEEL SPEED SENSOR SIGNAL GROUND: GROUND
I FH103–43 RH REAR WHEEL SPEED SENSOR SIGNAL: 46 PULSES PER WHEEL REVOLUTION
I FH103–45 LH FRONT WHEEL SPEED SENSOR SIGNAL: 46 PULSES PER WHEEL REVOLUTION
SG FH103–46 LH FRONT WHEEL SPEED SENSOR SIGNAL GROUND: GROUND
PG FH103–47 POWER GROUND – PUMP: GROUND
Page 82 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 05.2
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationCLUTCH PEDAL POSITION SENSOR CA287 6-WAY / BLACK TOP OF CLUTCH PEDAL
ELECTRONIC PARKING BRAKE SWITCH CA243 8-WAY / BLACK CENTER CONSOLE
FRONT ELECTRONIC MODULE CA24 26-WAY / NATURAL LH ‘A’ POST
CA31 20-WAY / BLACK
FH9 22-WAY / BLACK
FH59 12-WAY / BLACK
FH60 17-WAY / BLACK
NEUTRAL SWITCH (DIESEL) GB4 4-WAY / GREY TRANSMISSION, LH REAR
NEUTRAL SWITCH (GASOLINE) GB3 2-WAY / BLACK TRANSMISSION, LH REAR
PARKING BRAKE MODULE CA265 14-WAY / GREY LUGGAGE COMPARTMENT, RH REAR CA266 24-WAY / BLACK
PARKING BRAKE MOTOR CA269 6-WAY / GREY REAR SUSPENSION SUBFRAME
VARIABLE ASSIST STEERING ACTUATOR FH16 2-WAY / BLACK STEERING RACK PINION HOUSINGHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFH1 22-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
GB1 16-WAY / GREY / ENGINE HARNESS TO TRANSMISSION HARNESS ADJACENT TO TRANSMISSION BELL HOUSING
PI42 8-WAY / BLACK / ENGINE HARNESS TO FRONT HARNESS ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationCA141 UNDER LH FRONT SEAT
CA156 LUGGAGE COMPARTMENT, RH SIDE
FH77 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (FORWARD OF CA30)
PI40 (LHD) ENGINE COMPARTMENT, BEHIND RH WHEEL ARCH LINER
PI40 (RHD) ENGINE COMPARTMENT, BEHIND LH WHEEL ARCH LINER
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Parking Brake Module Pin Description and CharacteristicI CA265–3 IN-GEAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
SS CA265–5 SIGNAL SUPPLY VOLTAGE: NOMINAL 5 V
I CA265–6 CLUTCH PEDAL POSITION SENSOR FEEDBACK SIGNAL: VARIABLE VOLTAGE
O CA265–7 PARKING BRAKE MOTOR ENGAGE: ACTIVATE = B+
I CA265–10 PARKING BRAKE SWITCH – APPLY: CHANGE IN RESISTANCE
I CA265–11 PARKING BRAKE SWITCH – RELE ASE: CHANGE IN RESISTANCE
SS CA265–12 SIGNAL SUPPLY VOLTAGE: NOMINAL 5 V
SG CA265–13 SIGNAL GROUND: GROUND
O CA265–14 PARKING BRAKE MOTOR DISENGAGE: ACTIVATE = B+
B+ CA266–1 BATTERY POWER SUPPLY: B+
SG CA266–3 SIGNAL GROUND: GROUND
S CA266–4 SCP –
S CA266–5 SCP +
I CA266–10 PARKING BRAKE MOTOR POSITION SENSOR FEEDBACK SIGNAL: VARIABLE VOLTAGE
PG CA266–12 POWER GROUND: GROUND
PG CA266–13 POWER GROUND: GROUNDFront Electronic Module
Pin Description and CharacteristicS FH59–1 SCP –
S FH59–7 SCP +
PG FH59–12 POWER GROUND: GROUND
B+ FH60–1 SWITCHED SYSTEM POWER SUPPLY: B+
I FH60–2 VARIABLE ASSIST STEERING ACTUATOR RETURN: VARIABLE VOLTAGE
O FH60–9 VARIABLE ASSIST STEERING ACTUATOR DRIVE: B+ (PWM)
PG FH60–11 POWER GROUND: GROUND
PG FH60–13 POWER GROUND: GROUND
PG FH60–14 POWER GROUND: GROUND
PG FH60–15 POWER GROUND: GROUND
Page 83 of 200
Electronic Parking Brake; Variable Assist Power Steering
Jaguar S-TYPE 2005
Electronic Parking Brake; Variable Assist Power Steering
Fig. 05.2
13 4114
46 80
76 77 92
ll
15 45ll ll SS
81 118EE
Fig .01.1
Fig .01 .2 F
ig .01.3
Fig .01 .4
Fig . 01.5 F
ig . 01.6 F
ig .01 .7
Input
OutputI
O
B
P+Battery VoltagePower Ground Sensor/Signal Supply V
Sensor/Signal Ground Serial and Encoded Data
CAN
+
SCPC
S DD
–
D2B Network2
f05_2_200045
RW
WU RCA141
U Y
O
NR
R
B
CA156
44
P
P
FH60-2
NR
FH60-1
FH60-15
B
P
B
NG
FH60-14
B
P
FH60-13
B
P
FH59-12
B
P
FH60-11
B
P
FH77
FH60-9
O
WG
I
20.120.1
453R
150R
100R 100R
U
G
Y
WU B
4I
150R
453R
IIII I
H
GW
Y
YB
OI
B
U Y
FH59-7
FH59-1
20.220.2
SS
CA287-1 CA287-2
I
CAN
S60
G
CA287-3
CA266-3
CA265-5 CA265-6
150R
453R
CA243-6
CA243-1
150R
453R
APPLY
CA243-2
CA243-4
CA243-7
CA243-5
CA243-8
N
87
P
CA266 -11
VARIABLE ASSIST POWER STEERING
ELECTRONIC PARKING BRAKE
CA265-13 CA265-14
CA269-1
CA269-6
CA269-3
CA269-4
PARKING BRAKE MOTOR
CA266 -1
CA266-4
CA266-5 CA266-7
CA265-11
CA265-10
I
CA265-7
CA265-12
CA266-10
CA266-13
YG
I
YG
YG
YG
CA265-3
CA287-3
CA265-5
I
CA266-15
NEUTRAL SWITCH (DIESEL)
FH1-13
R
PI41-23
GB4-2
FH2-6
ELECTRONIC PARKING BRAKE SWITCH
GB3-2
GB3-1 PI42-5
FH16-1FH16-2
PS1-1
PS1-2
REFER TO APPENDIX:
EPB / CAN MESSAGES
C
C
PARKING BRAKE MODULE
B
CA116
CA266-12
GB1-12 FH1-2CA266-14
CA266-2
NEUTRAL SWITCH (GASOLINE)
GB1-16
PI41-27
GB GB GB
GB
CLUTCH PEDAL POSITION SENSOR *
GB1-13
RR
GB
GB4-4
PI41-35
GB1-16
GB GB
YG
GB4-1
GB1-15
PI41-12
YGYG
RN
CA269-5
CAS86
FRONT ELECTRONIC MODULE VARIABLE ASSIST
STEERING ACTUATOR
* Early production vehicles – feature not enabled.
B+
NOTE: Neutral Switch and Clutch Pedal Position Sensor – manual transmission vehicles only.
CAS90
(Gasoline only)
SWITCH ILLUMINATION RELEASE
WG
CA266 -9
B+
VEHICLE SPEED
G
CA266 -20
FC18-5
FC18-4
NR
WU WU WG
7
KEY-IN
IGNITION SWITCH
FCS11
CA61-76
CA61-67
F52 5A
REAR POWER DISTRIBUTION FUSE BOX
CA266-6
FC39-10FC39-5
FCS6
II
-1
GO
NR
CAS22
90
GO
BRAKE
ON / OFF SWITCHCA37 -2
(Diesel only)
B
CA265-13
CA269-5
(Japan only)
CAS89 CAS86
CAU5
CAS89
BRD
VARIANT:
All Vehicles
VIN RANGE: All
DATE OF ISSUE: May 2004
Page 84 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 05.3
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationDYNAMIC STABILITY CONTROL MODULE FH103 47-WAY / BLACK ENGINE COMPARTMENT, RH FRONT
ENGINE CONTROL MODULE PI1 134-WAY / BLACK FRONT BULKHEAD, P ASSENGER SIDE
FUEL / TRUNK RELEASE SWITCH PACK FC43 10-WAY / GREY INSTRUMENT PANEL
INSTRUMENT CLUSTER FC8 32-WAY / BLACK INSTRUMENT PANEL FC9 32-WAY / BLACK
SPEED CONTROL MODULE FC6 30-WAY / YELLOW INSTRUMENT PANEL, DRIVER SIDE
SPEED CONTROL SENSOR CC1 5-WAY / BLACK BELOW LH FRONT BUMPER
STEERING WHEEL — — STEERING WHEEL
TRANSMISSION CONTROL MODULE GB2 16-WAY / BLACK TRANSMISSION CONTROL VALVE ASSEMBLYHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFC4 14-WAY / GREEN / FASCIA HARNESS IN-LINE CONNECTOR BEHIND INSTRUMENT PANEL, LH SIDE
FC10 14-WAY / GREEN / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FC19 16-WAY / GREEN / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, LH SIDE
FC117 10-WAY / BLACK / STEERING WHEEL CASSETTE STEERING COLUMN
FH1 22-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH90 6-WAY / GREY / SPEED SENSOR LINK HARNESS TO FRONT HARNESS BELOW LH FRONT HEADLAMP ASSEMBLY
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationFC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH42 ENGINE COMPARTMENT, BEHIND RH HEADLAMP
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Speed Control Module Pin Description and CharacteristicO FC6–5 FORWARD ALERT SWITCH / INDICATOR DRIVE: FORWARD ALERT INDICATOR DRIVE
O FC6–6 CHIME MODULE DRIVE: CHIME ACTIVATE
C FC6–8 CAN –
C FC6–9 CAN +
PG FC6–12 POWER GROUND: GROUND
B+ FC6–14 IGNITION SWITCHED POWER SUPPLY: B+
B+ FC6–15 SWITCHED SYSTEM POWER SUPPLY: B+
I FC6–20 FORWARD ALERT SWITCH / INDICATOR DRIVE: MONITOR FORWARD ALERT SWITCH
C FC6–23 CAN –
C FC6–24 CAN +Dynamic Stability Control ModulePin Description and CharacteristicC FH103–11 CAN +
C FH103–12 CAN +
C FH103–14 CAN –
C FH103–15 CAN –Engine Control ModulePin Description and CharacteristicSS PI1–47 SPEED CONTROL SWITCH REQUEST: STEPPED RESISTANCE
I PI1–48 SPEED CONTROL SWITCHES SIGNAL GROUND: GROUND
C PI1–123 CAN –
C PI1–124 CAN +Instrument ClusterPin Description and CharacteristicC FC9–12 CAN +
C FC9–13 CAN –
C FC9–28 CAN +
C FC9–29 CAN –