2005 INFINITI QX4 key
[x] Cancel search: keyPage 754 of 3419
BCM (BODY CONTROL MODULE)
BCS-7
C
D
E
F
G
H
I
J
L
MA
B
BCS
Revision: October 20052005 QX56
BCM is activated with low current consumption mode.
CAN communication is not active.
When CAN communication operation is detected, it switches to CAN communication status.
When a state of the following switches changes, it switches to CAN communication state:
–Key switch
–Hazard switch
–Door lock/unlock switch
–Front door switch (LH, RH)
–Rear door switch (LH, RH)
–Back door switch
–Combination switch (passing, lighting switch 1st position, front fog lamp)
–Keyfob (lock/unlock signal)
–Door lock assembly LH (key cylinder switch)
When control performed only by BCM is required by switch, it shifts to CAN communication inactive
mode.
Status of combination switch reading function is changed.
SYSTEMS CONTROLLED BY BCM DIRECTLY
Power door lock system. Refer to BL-16, "POWER DOOR LOCK SYSTEM" .
Remote keyless entry system. Refer to BL-44, "REMOTE KEYLESS ENTRY SYSTEM" .
Power window system. Refer to GW-15, "POWER WINDOW SYSTEM" . NOTE
Sunroof system. Refer to RF-10, "SUNROOF" . NOTE
Room lamp timer. Refer to LT- 1 2 9 , "INTERIOR ROOM LAMP" .
Warning chime system. Refer to DI-42, "WARNING CHIME" .
Turn signal and hazard warning lamps system. Refer to LT-80, "TURN SIGNAL AND HAZARD WARNING
LAMPS" .
NOTE:
Power supply only. No system control.
SYSTEMS CONTROLLED BY BCM AND IPDM E/R
Panic system. Refer to BL-44, "REMOTE KEYLESS ENTRY SYSTEM" .
IVIS (NATS) system. Refer to BL-137, "IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)" .
Headlamp, tail lamp, front fog lamp, auto light and battery saver control systems. Refer to LT- 6 , "HEAD-
LAMP (FOR USA)" , LT- 3 3 , "HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -" , LT-108,
"PARKING, LICENSE PLATE AND TAIL LAMPS" , LT-69, "FRONT FOG LAMP" or LT-47, "AUTO LIGHT
SYSTEM" .
Front wiper and washer system. Refer to WW-4, "FRONT WIPER AND WASHER SYSTEM" .
Rear wiper and washer system. Refer to WW-35, "REAR WIPER AND WASHER SYSTEM" .
Rear window defogger system. Refer to GW-77, "REAR WINDOW DEFOGGER" .
MAJOR COMPONENTS AND CONTROL SYSTEM
System Input Output
Remote keyless entry system Keyfob
All-door locking actuator
Back door opener actuator
Turn signal lamp (LH, RH)
Power door lock systemFront power door lock/unlock
switch (LH, RH)All-door locking actuator
Power supply (IGN) to power window
and sunroofIgnition power supply Power supply to power window and sunroof system
Power supply (BAT) to power window
and sunroofBattery power supply Power supply to power window and sunroof system
Page 755 of 3419
BCS-8
BCM (BODY CONTROL MODULE)
Revision: October 20052005 QX56
CAN Communication System DescriptionEKS00D7X
Refer to LAN-5, "CAN COMMUNICATION" .
Panic alarmKey switch
KeyfobIPDM E/R
Auto light system
Auto light sensor
Combination switchIPDM E/R
Battery saver control
Ignition switch
Combination switchIPDM E/R
Headlamp Combination switch IPDM E/R
Tail lamp Combination switch IPDM E/R
Fog lamp Combination switch IPDM E/R
Turn signal lamp Combination switch
Turn signal lamp
Combination meter
Hazard lamp Hazard switch
Turn signal lamp
Combination meter
Room lamp timer
Key switch
Keyfob
Main power wndow and door
lock/unlock switch
Front door switch LH
All door switchInterior room lamp
Key warning chime
Key switch
Front door switch LHCombination meter (warning buzzer)
Light warning chime
Combination switch
Key switch
Front door switch LHCombination meter (warning buzzer)
Vehicle-speed-sensing intermittent
wiper
Combination switch
Combination meterIPDM E/R
Rear window defogger Rear window defogger switch IPDM E/R
Air conditioner switch signal Front air control ECM
Blower fan switch signal Front air control ECMSystem Input Output
Page 759 of 3419
BCS-12
BCM (BODY CONTROL MODULE)
Revision: October 20052005 QX56
4. Select item to be diagnosed on “SELECT TEST ITEM” screen.
ITEMS OF EACH PART
NOTE:
CONSULT-II will only display systems the vehicle possesses.
LKIA0183E
System and itemCONSULT-II
displayDiagnostic test mode (Inspection by part)
WORK
SUPPORTSELF−
DIAG
RESULTSCAN DIAG
SUPPORT
MNTRDATA
MONITORECU
PA R T
NUMBERACTIVE
TESTCON-
FIGU-
RATION
BCM BCM×× × × ×
Power door lock system DOOR LOCK×××
Rear defoggerREAR
DEFOGGER××
Warning chime BUZZER××
Room lamp timer INT LAMP×××
Remote keyless entry
systemMULTI REMOTE
ENT×××
Headlamp HEAD LAMP×××
Wiper (front/rear) WIPER×××
Turn signal lamp
Hazard lampFLASHER××
Blower fan switch signal
Air conditioner switch
signalAIR
CONDITIONER×
Combination switch COMB SW×
IVIS (NATS) IMMU××
Interior lamp battery
saverBATTERY
SAVER×××
Back door TRUNK××
Theft alarm THEFT ALM×××
Retained accessory
power controlRETAINED PWR×××
Oil pressure switch SIGNAL BUFFER××
Air pressure monitorAIR PRESSURE
MONITOR×× × ×
Panic alarm PANIC ALARM×
Page 760 of 3419
BCM (BODY CONTROL MODULE)
BCS-13
C
D
E
F
G
H
I
J
L
MA
B
BCS
Revision: October 20052005 QX56
WORK SUPPORT
Operation Procedure
1. Touch "BCM" on "SELECT TEST ITEM" screen.
2. Touch "WORK SUPPORT" on "SELECT DIAG MODE" screen.
3. Touch item on "SELECT WORK ITEM" screen.
4. Touch "START".
5. Touch "CHANGE SETT".
6. The setting will be changed and "CUSTOMIZING COM-
PLETED" will be displayed.
7. Touch "END".
Display Item List
CAN Communication Inspection Using CONSULT-II (Self-Diagnosis)EKS00D80
1. SELF-DIAGNOSTIC RESULT CHECK
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
1. Connect to CONSULT–II, and select “BCM” on “SELECT SYSTEM” screen.
2. Select “BCM” on “SELECT TEST ITEM” screen, and select “SELF-DIAG RESULTS”.
3. Check display content in self-diagnostic results.
Contents displayed
No malfunction>>Inspection End
Malfunction in CAN communication system>>After printing the monitor items, go to LAN-5, "
CAN COMMU-
NICATION" .
LKIA0183E
BCIA0031E
Item Description
RESET SETTING VALUE Return a value set with WORK SUPPORT of each system to a default value in factory shipment.
CONSULT-II display code Diagnosis item
U1000INITIAL DIAG
TRANSMIT DIAG
ECM
IPDM E/R
METER/M&A
I-KEY
Page 767 of 3419
BCS-20
BCM (BODY CONTROL MODULE)
Revision: October 20052005 QX56
Removal and Installation of BCMEKS00D82
REMOVAL
NOTE:
If possible, before removing BCM, retrieve current BCM configuration to use for reference when configuring
brand-new BCM after installation. Refer to BCS-14, "
Configuration" .
1. Disconnect negative battery cable.
2. Remove instrument panel storage bin. Refer to IP-10, "
Removal and Installation" .
3. Remove instrument lower panel LH. Refer to IP-10, "
Removal and Installation" .
4. Disconnect switch assembly.
5. Remove screw and release BCM.
6. Disconnect connectors and then remove BCM.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
When replacing BCM, it must be configured. Refer to BCS-14, "Configuration" .
When replacing BCM, perform initialization of NATS system and registration of all NATS ignition key IDs.
Refer to BL-137, "
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)" .
When replacing BCM, perform ID registration procedure of low tire pressure warning system. Refer to
WT-14, "
ID Registration Procedure" .
LEIA0068E
Page 768 of 3419
BL-1
BODY, LOCK & SECURITY SYSTEM
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION BL
A
B
BL
Revision: October 20052005 QX56 PRECAUTIONS .......................................................... 4
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 4
Precautions for work ................................................ 4
PREPARATION ........................................................... 5
Special service tool .................................................. 5
Commercial Service Tool ......................................... 5
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 6
Work Flow ................................................................ 6
CUSTOMER INTERVIEW ..................................... 6
DUPLICATE THE NOISE AND TEST DRIVE ....... 7
CHECK RELATED SERVICE BULLETINS ........... 7
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ...................................................... 7
REPAIR THE CAUSE ........................................... 7
CONFIRM THE REPAIR ....................................... 8
Generic Squeak and Rattle Troubleshooting ........... 8
INSTRUMENT PANEL .......................................... 8
CENTER CONSOLE ............................................. 8
DOORS ................................................................. 8
TRUNK .................................................................. 9
SUNROOF/HEADLINING ..................................... 9
OVERHEAD CONSOLE (FRONT AND REAR) ..... 9
SEATS ................................................................... 9
UNDERHOOD ....................................................... 9
Diagnostic Worksheet ............................................ 10
HOOD ....................................................................... 12
Fitting Adjustment .................................................. 12
CLEARANCE AND SURFACE HEIGHT
ADJUSTMENT .................................................... 13
HOOD LOCK ADJUSTMENT ............................. 13
Removal and Installation of Hood Assembly .......... 13
Removal and Installation of Hood Lock Control ..... 14
REMOVAL ........................................................... 14
INSTALLATION ................................................... 15
Hood Lock Control Inspection ................................ 15
POWER DOOR LOCK SYSTEM .............................. 16
Component Parts and Harness Connector Location ... 16
System Description ................................................ 17OUTLINE ............................................................. 18
Schematic ............................................................... 19
Wiring Diagram — D/LOCK — ............................... 20
Terminals and Reference Value for BCM ............... 25
Work Flow ............................................................... 25
CONSULT–II Function (BCM) ................................ 26
CONSULT–II INSPECTION PROCEDURE ......... 26
DATA MONITOR ................................................. 27
ACTIVE TEST ..................................................... 28
Trouble Diagnoses Symptom Chart ....................... 29
BCM Power Supply and Ground Circuit Check ...... 29
Door Switch Check ................................................. 31
Key Switch (Insert) Check ...................................... 33
Door Lock/Unlock Switch Check ............................ 34
Glass Hatch Switch Circuit Inspection .................... 36
Front Door Lock Assembly LH (Actuator) Check .... 38
Front Door Lock Actuator RH Check ...................... 39
Rear Door Lock Actuator RH/LH Check ................. 40
Glass Hatch Lock Actuator Check .......................... 41
Front Door Lock Assembly LH (Key Cylinder Switch)
Check ..................................................................... 42
REMOTE KEYLESS ENTRY SYSTEM ..................... 44
Component Parts and Harness Connector Location ... 44
System Description ................................................. 45
INPUTS ............................................................... 45
OPERATING PROCEDURE ................................ 46
CAN Communication System Description .............. 48
Schematic ............................................................... 49
Wiring Diagram — KEYLES — ............................... 50
............................................................................ 50
............................................................................ 51
............................................................................ 52
Terminals and Reference Value for BCM ............... 53
Terminals and Reference Value for IPDM E/R ....... 54
CONSULT-II Function (BCM) ................................. 55
CONSULT-II Inspection Procedure ......................... 55
“MULTI REMOTE ENT” ....................................... 55
CONSULT-II Application Items ............................... 56
“MULTI REMOTE ENT” ....................................... 56
Trouble Diagnosis Procedure ................................. 59
Page 769 of 3419
BL-2Revision: October 20052005 QX56 BCM Power Supply and Ground Circuit Check ...... 59
Trouble Diagnoses .................................................. 60
SYMPTOM CHART ............................................. 60
Key Switch (Insert) Check ...................................... 62
Door Switch Check ................................................. 63
Keyfob Battery and Function Check ....................... 65
Remote Keyless Entry Receiver System Check ..... 66
ACC Power Check .................................................. 68
IPDM E/R Operation Check .................................... 68
Check Hazard Function .......................................... 70
Check Horn Function .............................................. 70
Check Headlamp Function ..................................... 70
Check Map Lamp Illumination Function ................. 70
ID Code Entry Procedure ....................................... 71
KEYFOB ID SET UP WITH CONSULT-II ............ 71
KEYFOB ID SET UP WITHOUT CONSULT-II ..... 73
Keyfob Battery Replacement .................................. 74
VEHICLE SECURITY (THEFT WARNING) SYSTEM ... 75
Component Parts and Harness Connector Location ... 75
System Description ................................................. 76
DESCRIPTION .................................................... 76
POWER SUPPLY AND GROUND CIRCUIT ....... 77
INITIAL CONDITION TO ACTIVATE THE SYS-
TEM ..................................................................... 77
VEHICLE SECURITY SYSTEM ALARM OPER-
ATION .................................................................. 77
VEHICLE SECURITY SYSTEM DEACTIVATION ... 78
PANIC ALARM OPERATION ............................... 78
CAN Communication System Description .............. 78
Schematic ............................................................... 79
Wiring Diagram — VEHSEC — .............................. 80
............................................................................. 80
............................................................................. 81
............................................................................. 82
............................................................................. 83
............................................................................. 84
Terminals and Reference Value for BCM ................ 85
Terminals and Reference Value for IPDM E/R ........ 86
CONSULT-II Function (BCM) .................................. 86
CONSULT-II INSPECTION PROCEDURE .......... 86
CONSULT-II APPLICATION ITEM ....................... 88
Trouble Diagnosis ................................................... 89
WORK FLOW ...................................................... 89
Preliminary Check .................................................. 90
Symptom Chart ....................................................... 91
Door Switch Check ................................................. 92
Hood Switch Check ................................................ 94
Combination Meter (Security Indicator Lamp)
Check ..................................................................... 95
Front Door Lock Assembly LH (Key Cylinder Switch)
Check ..................................................................... 96
Vehicle Security Horn Alarm Check ........................ 98
Vehicle Security Headlamp Alarm Check ............... 98
Door Lock/Unlock Switch Check ............................ 98
AUTOMATIC BACK DOOR SYSTEM ....................... 99
Component Parts and Harness Connector Location ... 99
System Description ...............................................100
OPERATION DESCRIPTION ............................100
Schematic .............................................................105Wiring Diagram — B/CLOS — .............................. 106
Terminals and Reference Value for Back Door Con-
trol Unit .................................................................. 111
Terminals and Reference Value for BCM ..............112
Trouble Diagnosis Procedure ................................113
Self-Diagnosis Procedures ...................................113
INPUT SIGNAL CHECK MODE .........................113
OPERATING CHECK MODE .............................113
Diagnosis Chart ....................................................114
Back Door Power Supply and Ground Circuit
Inspection ..............................................................115
Power Liftgate Switch System Inspection .............116
GLASS HATCH AJAR SWITCH CHECK ...........117
Back Door Close (Close) Switch System Inspection .118
Back Door Close (Cancel) Switch System Inspec-
tion ........................................................................119
Pinch Strip System Inspection .............................. 121
Back Door Warning Chime System Inspection ..... 122
Half-Latch Switch System Inspection .................... 122
Open Switch System Inspection ........................... 123
Close Switch System Inspection ........................... 124
Back Door Handle Switch System Inspection ....... 125
Cinch Latch Motor System Inspection .................. 126
DOOR ...................................................................... 128
Fitting Adjustment ................................................. 128
FRONT DOOR ................................................... 128
REAR DOOR ..................................................... 128
STRIKER ADJUSTMENT .................................. 128
Removal and Installation ....................................... 129
FRONT DOOR ................................................... 129
REAR DOOR ..................................................... 129
BACK DOOR ..................................................... 130
FRONT DOOR LOCK .............................................. 131
Component Structure ............................................ 131
Removal and Installation ....................................... 131
REMOVAL .......................................................... 131
INSTALLATION .................................................. 133
Disassembly and Assembly .................................. 133
DOOR KEY CYLINDER ASSEMBLY ................. 133
REAR DOOR LOCK ................................................ 134
Component Structure ............................................ 134
Removal and Installation ....................................... 134
REMOVAL .......................................................... 134
INSTALLATION .................................................. 134
BACK DOOR LOCK ................................................ 135
Power Back Door Opener ..................................... 135
REMOVAL ......................................................... 135
INSTALLATION ................................................. 135
Door Lock Assembly ............................................. 136
REMOVAL ......................................................... 136
INSTALLATION ................................................. 136
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-
NATS) ...................................................................... 137
Component Parts and Harness Connector Location . 137
System Description ............................................... 138
System Composition ............................................. 138
ECM Re-communicating Function ........................ 139
Wiring Diagram — NATS — .................................. 140
Terminals and Reference Value for BCM .............. 141
Page 772 of 3419
PREPARATION
BL-5
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: October 20052005 QX56
PREPARATIONPFP:00002
Special service toolEIS008P5
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service ToolEIS008P6
Tool number
(Kent-Moore No.)
Tool nameDescription
—
(J-39570)
Chassis earLocating the noise
—
(J-43980)
NISSAN Squeak and Rat-
tle KitRepairing the cause of noise
—
(J-43241)
Remote Keyless Entry
TesterUsed to test keyfobs
SIIA0993E
SIIA0994E
LEL946A
Tool name
(Kent-Moore No.)Description
Engine ear
(J-39565)Locating the noise
SIIA0995E