2005 INFINITI QX4 brake sensor

FAX-6
WHEEL HUB
Revision: October 20052005 QX56
4. Put alignment mark on disc rotor and wheel hub and bearing
assembly, then remove disc rotor.
5. Remove cotter pin, then remove lock nut from drive shaft using power tool. Refer to FA X -7 , "
Removal and
Installation" .
6. Remove drive shaft from wheel hub and bearing assembly. Refer to FAX-7, "
Removal and Installation" .
7. Remove ABS sensor. Refer to BRC-64, "
Removal and Installation" .

Inspect the ABS sensor O-ring, replace the ABS sensor assembly if damaged.

Clean the ABS sensor hole and mounting surface with a suitable brake cleaner and clean lint-free shop
rag. Be careful that dirt and debris do not enter the axle bearing area.

Apply a coat of suitable grease to the ABS sensor O-ring and mounting hole.
CAUTION:
Do not pull on the ABS sensor harness.
8. Remove wheel hub and bearing assembly bolts using power tool.
9. Remove splash guard and wheel hub and bearing assembly from steering knuckle.
INSPECTION AFTER REMOVAL
Check for deformity, cracks and damage on each part, replace if necessary.
INSTALLATION
Installation is in the reverse order of removal.

Use new bolts when installing the wheel hub and bearing assembly.

When installing disc rotor on wheel hub and bearing assembly,
position the disc rotor according to alignment mark.
(When not using the alignment mark, refer to BR-21, "
Removal
and Installation of Brake Caliper Assembly and Disc Rotor" .)

When installing wheel and tire. Refer to WT-7, "Rotation" .
WDIA0044E
WDIA0044E

DRIVE SHAFT
FAX-7
C
E
F
G
H
I
J
K
L
MA
B
FA X
Revision: October 20052005 QX56
DRIVE SHAFTPFP:39100
Removal and InstallationEDS001XF
REMOVAL
1. Remove wheel and tire using power tool.
2. Remove engine under cover using power tool.
3. Remove ABS sensor harness from mount on knuckle.
CAUTION:
Do not pull on ABS sensor harness.
4. Without disassembling the hydraulic lines, remove brake caliper using power tool. Reposition it aside with
wire. Refer to BR-21, "
Removal and Installation of Brake Caliper Assembly and Disc Rotor" .
NOTE:
Avoid depressing brake pedal while brake caliper is removed.
5. Remove coil spring and shock absorber assembly using power tool. Refer to FSU-10, "
Removal and
Installation" .
6. Separate upper link ball joint stud from steering knuckle using
Tool.

Support lower link with jack.
7. Remove cotter pin, then remove drive shaft nut.
8. Remove drive shaft mounting bolts from front final drive.
9. Remove drive shaft from wheel hub and bearing assembly.
CAUTION:

When removing drive shaft, do not apply an excessive
angle to drive shaft joint. Also be careful not to exces-
sively extend slide joint.
INSPECTION AFTER REMOVAL

Move joint up, down, left, right, and in axial direction. Check for any rough movement or significant loose-
ness.

Check boot for cracks or other damage, and for grease leakage.

If damaged, disassemble drive shaft to verify damage, and
repair or replace as necessary.
1. Cotter pin 2. Drive shaft nut 3. Drive shaft
LDIA0159E
Tool number : ST29020001 (J-24319-01)
LEIA0095E
RAA0030D

KNUCKLE
FSU-17
C
D
F
G
H
I
J
K
L
MA
B
FSU
Revision: October 20052005 QX56
KNUCKLEPFP:40014
On-Vehicle Inspection and ServiceEES001GR
Make sure the mounting conditions (looseness, backlash) of each component and component status (wear,
damage) are within specifications. Refer to FSU-21, "
Ball Joint" .
Removal and InstallationEES001GS
REMOVAL
1. Remove wheel and tire from vehicle using power tool.
2. Without disconnecting the hydraulic lines, remove brake caliper using power tool. Reposition it aside with
wire. Refer to BR-21, "
Removal and Installation of Brake Caliper Assembly and Disc Rotor" .
CAUTION:
It is not necessary to remove bolts on torque member and brake hose except for disassembly or
replacement of caliper assembly. In this case, hang cylinder body with a wire so that the brake
hose in not under tension.
NOTE:
Avoid depressing brake pedal while brake caliper is removed.
3. Put alignment marks on disc rotor and wheel hub and bearing
assembly, then remove disc rotor.
4. Remove ABS sensor from steering knuckle. Refer to BRC-64, "
Removal and Installation" .
CAUTION:
Do not pull on ABS sensor harness.
5. Remove cotter pin, then remove lock nut from drive shaft using power tool.
6. Remove steering outer socket cotter pin at steering knuckle, then loosen mounting nut using power tool.
1. Disc rotor 2. Wheel hub and bearing assembly 3. Wheel stud
4. Splash guard 5. Steering knuckle
WDIA0043E
WDIA0044E

GI-10
HOW TO USE THIS MANUAL
Revision: October 20052005 QX56
SYMBOLS
1. Union bolt 2. Copper washer 3. Brake hose
4. Cap 5. Bleed valve 6. Sliding pin bolt
7. Piston seal 8. Piston 9. Piston boot
10. Cylinder body 11. Sliding pin 12. Torque member mounting bolt
13. Washer 14. Sliding pin boot 15. Bushing
16. Torque member 17. Inner shim cover 18. Inner shim
19. Inner pad 20. Pad retainer 21. Pad wear sensor
22. Outer pad 23. Outer shim 24. Outer shim cover
1: PBC (Poly Butyl Cuprysil) grease
or silicone-based grease2: Rubber grease : Brake fluid
Refer to GI section for additional symbol definitions.
SFIA2959E
SAIA0749E

IDX-2
ALPHABETICAL INDEX
Numerics
2-4WD shift solenoid valve ..... TF-94
, TF-152, TF-165
4WD - Wiring diagram ....................................... TF-24
4WD shift switch ................................................ TF-66
4WD solenoid valve ................ TF-90, TF-152, TF-165
4WD system description .................................... TF-15
4WD system diagram ........................................ TF-19
A
A/C air flow ...................................................... ATC-29
A/C compressor clutch removal and installation .. ATC-
180
A/C compressor mounting ............................. ATC-179
A/C compressor precaution ............................. ATC-11
A/C compressor special service tool ................ ATC-14
A/C control operation (auto A/C) ...................... ATC-26
A/C diagnostic work flow (auto A/C) .............. ATC-132
A/C evaporator ............................................... ATC-186
A/C HFC134a (R134a) system identification ..... ATC-7
A/C HFC134a (R134a) system precaution ........ ATC-5
A/C HFC134a (R134a) system service procedure ATC-
175
A/C HFC134a (R134a) system service tools ... ATC-14
A/C HFC134a system service equipment precaution ...
ATC-11
A/C lubricant (R134a) ...................................... ATC-22
A/C lubrication oil ............................................. ATC-22
A/C operational check ....................... ATC-57, ATC-60
A/C self-diagnoses (auto A/C) ........ ATC-55, ATC-132
A/C service data specification ........................ ATC-193
A/C trouble diagnoses (auto A/C) .................... ATC-33
A/C, A - Wiring diagram ................................... ATC-43
A/T fluid checking ...................... AT-13, AT-50, MA-22
A/T fluid cooler cleaning .................................... AT-13
A/T fluid replacement ............................. AT-13, MA-24
A/T fluid temperature sensor ........................... AT-126
A/T IND - Wiring diagram .................................... DI-40
A/T indicator ........................................................ DI-40
A/T shift lock system ........................................ AT-222
A/T trouble diagnoses ........................................ AT-41
A/T Wiring diagram AT - CAN ............................ AT-96
A/T Wiring diagram AT - FTS .......................... AT-127
A/T Wiring diagram AT - MAIN ........................ AT-168
A/T Wiring diagram AT - NONDTC .................. AT-177
A/T Wiring diagram AT - PNP/SW ................... AT-105
A/T Wiring diagram AT - STSIG ...................... AT-100
A/T Wiring diagram AT - VSS A/T ................... AT-110
ABS - Wiring diagram ..................................... BRC-16
ABS (anti-lock brake system) ........................... BRC-7
Accelerator control system ............................... ACC-2
Accelerator pedal position (APP) sensor . EC-591, EC-
597, EC-611
Accelerator pedal released position learning ..... EC-90
AF1B1-Wiring diagram EC-461, EC-470, EC-479, EC-
489, EC-500, EC-510, EC-522
AF1B2-Wiring diagram EC-463, EC-472, EC-481, EC-
491, EC-502, EC-512, EC-524
AF1HB1-Wiring diagram ................................. EC-387
AF1HB2-Wiring diagram ................................. EC-389
Aiming adjustment .................................. LT-30, LT-78
Air bag ............................................................... SRS-3
Air cleaner and air duct ..................................... EM-14
Air cleaner filter replacement ............................ MA-16
Air conditioner cut control ................................. EC-28
Air flow meter - See Mass air flow sensor EC-174, EC-
183
Air fuel ratio sensor 1 .. EC-459, EC-468, EC-477, EC-
487, EC-497, EC-507, EC-519
Air fuel ratio sensor 1 heater ........................... EC-386
Air mix. door motor .......................................... ATC-70
Ambient sensor ............................. ATC-137, ATC-148
Angular tightening application ............................. EM-3
APPS1 - Wiring diagram ................................. EC-593
APPS2 - Wiring diagram ................................. EC-599
APPS3 - Wiring diagram ................................. EC-613
ASC/BS - Wiring diagram ............................... EC-571
ASC/SW - Wiring diagram .............................. EC-554
ASCBOF - Wiring diagram .............................. EC-658
ASCD ................................................................ EC-29
ASCD (automatic speed control device) ........... ACS-3
ASCD brake switch ........................... EC-569, EC-657
ASCD indicator lamp ....................................... EC-664
ASCD steering switch ..................................... EC-552
ASCIND - Wiring diagram ............................... EC-665
ATP switch ............................ TF-107, TF-110, TF-115
AUDIO - Wiring diagram .................................... AV-10
AUT/DP - Wiring diagram .................................. SE-20
Auto air conditioner - Wiring diagram .............. ATC-43
Auto anti-dazzling inside mirror ........... GW-75, GW-76
Autolamp ............................................................ LT-47
Automatic amplifier ......................................... ATC-61
Automatic drive positioner .................................. SE-11
Automatic transmission number .......................... GI-48
AV and NAVI control unit ................................... AV-63
AV communication line ...................................... AV-87
B
Back door ........................................................... BL-99
Back door trim ..................................................... EI-32
Back sonar .......................................................... DI-58
BACK/L - Wiring diagram ................................. LT-106
Back-up lamp ................................................... LT-106
Ball joint (front) ................................................ FSU-15
Basic inspection ................................................ EC-72
Battery ................................................................. SC-4
Battery/Starting/Charging System Tester SC-6, SC-12,
SC-19
BCM (Body control module) .............................. BCS-3
Block heater ...................................................... EM-73
Blower motor ................................... ATC-93, ATC-152
Body alignment ................................................ BL-172
Body component parts ..................................... BL-161
Body construction ............................................ BL-171
Body exterior paint color .................................. BL-160
Body mounting ................................................. BL-159

IDX-3
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Body repair ....................................................... BL-160
Body sealing ..................................................... BL-168
Brake booster .................................................... BR-16
Brake fluid level ................................................. MA-28
Brake hydraulic line ........................................... BR-11
Brake inspection ................................................ MA-28
Brake lines and cables inspection ..................... MA-28
Brake master cylinder ....................................... BR-14
Brake switch ...................................... EC-569, EC-586
BRK/SW - Wiring diagram ............................... EC-587
Bulb specifications ........................................... LT-170
Bumper, front ...................................................... EI-13
Bumper, rear ....................................................... EI-15
C
Camshaft ........................................................... EM-43
Camshaft inspection .......................................... EM-46
Camshaft position sensor (PHASE) ................ EC-291
CAN - Wiring diagram EC-164, LAN-18, LAN-52, LAN-
92, LAN-128
CAN (Controller Area Network) BRC-10, SE-17, LAN-
16, LAN-50, LAN-90, LAN-126
CAN communication ... EC-31, EC-163, AT-95, TF-20,
TF-113
, BRC-10, SE-17, LAN-16, LAN-50, LAN-90,
LAN-126
Canister-See EVAP canister ............................. EC-35
Center case (Transfer) ....................... TF-152, TF-165
CHARGE - Wiring diagram ............................... SC-18
Charging system ............................................... SC-17
Chassis and body maintenance ........................ MA-21
Chassis and body maintenanceSchedule 1 ........ MA-8
Chassis and body maintenanceSchedule 2 ...... MA-10
CHIME - Wiring diagram ..................................... DI-44
Circuit breaker ................................................... PG-66
Clock ................................................................... DI-69
CLOCK - Wiring diagram .................................... DI-69
Closed loop control ........................................... EC-25
Closed loop control (Bank 1) ........................... EC-437
Closed loop control (Bank 2) ........................... EC-437
Clutch drum (Transfer) ....................... TF-152, TF-165
Clutch pressure switch (Transfer) ...... TF-152, TF-165
Coil spring (front) ............................................. FSU-10
Collision diagnosis .......................................... SRS-61
Combination lamp, front, removal and installation . LT-
32
Combination lamp, rear, removal and installation .. LT-
122
Combination meter ................................................ DI-5
Combination switch ............................................ LT-97
COMBSW - Wiring diagram ............................... LT-97
COMM - Wiring diagram ................................... AV-87
COMPAS - Wiring diagram ................................. DI-27
Compass ............................................................. DI-26
Component Location (auto A/C) ...................... ATC-39
Compressor clutch removal and installation . ATC-180
Compressor mounting ................................... ATC-179
Compressor precaution ................................... ATC-11
Compressor special service tool ..................... ATC-14
Condenser ..................................................... ATC-185
Connecting rod .................................................. EM-91
Connecting rod bearing clearance ..................... EM-91
Connecting rod bushing clearance .................... EM-91
Console box - See Instrument panel ................... IP-10
CONSULT for VDC ......................................... BRC-28
CONSULT general information ........................... GI-37
CONSULT-II for engine ................................... EC-126
Control units (terminal arrangement) ................. PG-71
Control valve (A/T) ............................................. AT-35
Control valve (Transfer) ...................... TF-152, TF-165
Controller Area Network (CAN) BRC-10, SE-17, LAN-
16, LAN-50, LAN-90, LAN-126
Converter housing installation ............ AT-246, AT-249
COOL/F - Wiring diagram ................................ EC-443
Coolant mixture ratio ......................................... MA-12
Coolant replacement ......................................... MA-13
Cooling circuit (engine) ........................................ CO-8
Cooling fan ........................................................ CO-15
Cooling fan control ........................................... EC-440
Cooling fan motor ............................................ EC-449
Cooling unit (A/C evaporator) ....... ATC-156, ATC-186
Corrosion protection ......................................... BL-165
Crankcase ventilation system - See Positive crankcase
ventilation .......................................................... EC-45
Crankshaft ......................................................... EM-74
Crankshaft position sensor (POS) ................... EC-284
Crash zone sensor .......................................... SRS-56
CVT shift lock system - Wiring diagram ........... AT-223
Cylinder block .................................................... EM-73
Cylinder block boring ......................................... EM-94
D
D/LOCK - Wiring diagram ................................... BL-19
Data link connector for Consult ......... EC-128, EC-140
Daytime light system .......................................... LT-33
Daytime running light - See Daytime light system .. LT-
33
Diagnosis sensor unit ...................................... SRS-59
Diagnostic trouble code (DTC) for OBD system . EC-8,
EC-53
Diagnostic trouble code (DTC) inspection priority chart
EC-101
Differential carrier assembly ............................ RFD-12
Differential carrier disassembly ....................... RFD-14
Differential gear oil replacement ........................ MA-25
Dimensions ......................................................... GI-49
Direct clutch solenoid valve ................ AT-148, AT-150
Display and amp.assembly .............................. ATC-61
Display Control Unit ......................................... AV-158
Dome light - See Interior lamp .......................... LT-129
Door glass .......................................... GW-68, GW-71
Door lock .......................................................... BL-131
Door mirror lamp ............................................... LT-129
Door trim .............................................................. EI-32
Door, front ........................................... BL-128, GW-68
Door, rear ........................................... BL-128, GW-71
Drive belt ........................................................... EM-12

IDX-4
ALPHABETICAL INDEX
Drive chain (Transfer) ......................... TF-147, TF-174
Drive pinion diff. inspection ............................. RFD-13
Drive pinion height .......................................... RFD-18
Drive shaft (rear) ............................................... RAX-7
Driver air bag .................................................. SRS-46
DTC work support ............................................ EC-136
DTRL - Wiring diagram ....................................... LT-37
Duct and grilles .............................................. ATC-170
DVD Player ........................................................ AV-60
E
ECM input/output signal ..................... EC-117
, EC-141
ECM power supply ............................. EC-157, EC-393
ECM relay ........................................................ EC-157
ECM/PW - Wiring diagram ............................... EC-394
ECTS - Wiring diagram .................................... EC-197
Electric sunroof .................................................. RF-10
Electric throttle control actuator ......... EC-397, EC-399
Electrical load signal circuit .............................. EC-648
Electrical units location ...................................... PG-63
Electronic ignition (EI) system ........................... EC-26
Engine control circuit diagram ......................... EC-115
Engine control component parts location ......... EC-108
Engine control module (ECM) .......................... EC-383
Engine control system diagram ......................... EC-23
Engine coolant .................................................. CO-10
Engine coolant temperature sensor (ECTS) ... EC-195,
EC-208
Engine fail-safe system .................................... EC-103
Engine oil ............................................................. LU-7
Engine oil filter replacement ............................. MA-17
Engine oil precautions .......................................... GI-7
Engine oil replacement ..................................... MA-17
Engine removal ................................................. EM-69
Engine room cover ............................................ EM-11
Engine serial number .......................................... GI-48
ETC1 - Wiring diagram .................................... EC-400
ETC2 - Wiring diagram .................................... EC-407
ETC3 - Wiring diagram .................................... EC-411
EVAP canister .................................................... EC-35
EVAP canister purge volume control solenoid valve ....
EC-318
, EC-531
EVAP canister vent control valve ....... EC-325, EC-539
EVAP control system (small leak) diagnosis .. EC-309,
EC-349
, EC-357
EVAP control system pressure sensor .... EC-332, EC-
335, EC-341
EVAP control system purge flow monitoring diagnosis
EC-304
EVAP vapor lines inspection ............................. MA-20
Evaporative emission (EVAP) system ............... EC-32
Evaporator ..................................................... ATC-186
Exhaust manifold .............................................. EM-19
Exhaust system ................................................... EX-3
Exhaust system inspection .................................. EX-3
Expansion valve ............................................. ATC-188
F
F/FOG - Wiring diagram ..................................... LT-71
F/PUMP - Wiring diagram ............................... EC-638
Final drive pre-inspection .................. FFD-14, RFD-13
Final drive removal and installation ... FFD-11, RFD-10
Flow charts .......................................................... GI-27
Fluid temperature sensor (A/T) ........................ AT-126
Fluids ................................................................ MA-11
Fluorescent leak detector .............................. ATC-189
Fog lamp, front ................................................... LT-69
Foot lamp ......................................................... LT-130
Freeze frame data ............................... EC-54, EC-130
Front brake solenoid valve ................. AT-144, AT-146
Front bumper ...................................................... EI-13
Front case (Transfer) .......................... TF-147, TF-174
Front combination lamp removal and installation LT-32
Front door ............................. BL-128, BL-131, GW-68
Front Door Trim ................................................... EI-32
Front drive shaft (Transfer) ................. TF-147, TF-174
Front fog lamp .................................................... LT-69
Front passenger air bag .................................. SRS-51
Front seat ........................................................... SE-97
Front seat belt ...................................................... SB-3
Front seat belt pre-tensioner ............... SRS-3, SRS-58
Front washer ...................................................... WW-4
Front wiper ......................................................... WW-4
FTTS - Wiring diagram ...................... EC-255, EC-260
Fuel cut control (at no load high engine speed) EC-27
Fuel filter replacement ......................................... FL-5
Fuel gauge ............................................................ DI-5
Fuel injection system (Bank 1) .......... EC-236, EC-245
Fuel injection system (Bank 2) .......... EC-236, EC-245
Fuel injector and fuel tube ................................. EM-29
Fuel level sensor ................. EC-366, EC-368, EC-370
Fuel line inspection .............................................. FL-3
Fuel pressure check .......................................... EC-93
Fuel pressure release ....................................... EC-93
Fuel pump ....................................................... EC-637
Fuel pump and gauge .......................................... FL-5
Fuel system .......................................................... FL-3
Fuel tank .............................................................. FL-9
Fuel tank temperature sensor ........... EC-253, EC-259
Fuel tank vacuum relief valve ........................... EC-35
FUELB1 - Wiring diagram ................. EC-238, EC-247
FUELB2 - Wiring diagram ................. EC-239, EC-248
Fuse ...................................................... PG-66, PG-77
Fuse and fusible link box .................................. PG-77
Fuse block ......................................................... PG-76
Fusible link ............................................ PG-66, PG-77
G
Garage jack and safety stand ............................. GI-40
Gauges ................................................................. DI-5
Generator .......................................................... SC-17
Generic scan tool (GST) ................................. EC-139
Glass ...................................... GW-11, GW-68, GW-71
Glove box lamp ................................................ LT-153

IDX-5
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
GPS antenna ..................................................... AV-62
Grease .............................................................. MA-11
Ground distribution ............................................ PG-29
H
H/AIM - Wiring diagram ...................................... LT-66
Handling precautions for plastics ..................... BL-187
Harness connector ............................................ PG-67
Harness layout .................................................. PG-39
Hazard warning lamp ......................................... LT-80
Headlamp aiming control ................................... LT-66
Headlamp leveler - See Headlamp aiming control . LT-
66
Headlamp removal and installation .................... LT-32
Heated oxygen sensor 2 (bank 1) .... EC-216, EC-225,
EC-415
, EC-426
Heated oxygen sensor 2 (bank 2) .... EC-216, EC-225,
EC-415
, EC-426
Heated oxygen sensor 2 heater (bank 1) ........ EC-166
Heated oxygen sensor 2 heater (bank 2) ........ EC-166
Heated seat ....................................................... SE-90
Heater and cooling unit (Heater core) . ATC-156, ATC-
160
Heater unit (heater core) ............... ATC-156, ATC-160
Height (Dimensions) ........................................... GI-49
HFC134a (R134a) system identification ........... ATC-7
HFC134a (R134a) system precaution ............... ATC-5
HFC134a (R134a) system service procedure ATC-175
HFC134a (R134a) system service tools ......... ATC-14
HFC134a system service equipment precaution ATC-
11
High & low reverse clutch solenoid valve . AT-152, AT-
154
Homelink universal transceiver ........................ BL-156
Horn ................................................................ WW-58
HORN - Wiring diagram .................................. WW-58
How to erase DTC for OBD system .................. EC-62
HSEAT - Wiring diagram ................................... SE-92
I
I/MIRR - Wiring diagram ................................... GW-75
IATS - Wiring diagram ..................................... EC-192
ICC - Wiring diagram ....................................... ACS-20
ICC/BS - Wiring diagram ................................. EC-562
ICC/SW - Wiring diagram ................................ EC-547
ICCBOF - Wiring diagram ............................... EC-650
Identification plate .............................................. GI-47
Idle air volume learning ..................................... EC-91
Idle mixture ratio ................................................ EC-79
Idle speed .............................................. EC-72, EC-77
Idle speed control (ISC) .................... EC-374, EC-376
Ignition coil .......................................... EM-26, EC-619
Ignition control system .................................... EC-619
Ignition key hole illumination ............................ LT-129
Ignition timing ........................................ EC-72, EC-77
IGNSYS - Wiring diagram ............................... EC-620
ILL - Wiring diagram ......................................... LT-158
Illumination ....................................................... LT-152
In vehicle sensor ........................... ATC-140, ATC-149
INJECT - Wiring diagram ................................. EC-632
Injector ............................................................. EC-631
Input clutch solenoid valve ................. AT-140, AT-142
Instrument panel .................................................. IP-10
Instrument panel speaker .................................. AV-46
Intake air temperature sensor ............ EC-191, EC-211
Intake door control linkage adjustment . ATC-85, ATC-
88
Intake door motor ........................... ATC-83, ATC-164
Intake manifold .................................................. EM-15
Intake sensor ................................ ATC-145, ATC-151
Integrated homelink transmitter - See Homelink univer-
sal tranceiver .................................................... BL-156
Intelligent cruise control (ICC) system ............... ACS-6
Interior ................................................................. EI-35
Interior lamp ...................................................... LT-129
Interior lamp on-off control ................................ LT-130
Internal gear (Transfer) ....................... TF-147, TF-174
IPDM (Intelligent power distribution module engine
room) ................................................................. PG-17
IVIS (Infiniti vehicle immobilizer system) .......... BL-137
IVIS (Infiniti vehicle immobilizer system) precautions ...
GI-3
J
Jacking points ..................................................... GI-40
Junction box (J/B) .............................................. PG-76
K
Key illumination ................................................ LT-130
KEYLES - Wiring diagram .................................. BL-49
Knock sensor (KS) ........................................... EC-279
KS - Wiring diagram ........................................ EC-280
L
Length (Dimensions) .......................................... GI-49
License lamp .................................................... LT-108
Lifting points ....................................................... GI-41
Line pressure solenoid valve ........................... AT-119
Line pressure switch (Transfer) .......... TF-152, TF-165
Line pressure test (A/T) ..................................... AT-51
Location of electrical units ................................. PG-63
Low coast brake solenoid valve .......... AT-156, AT-158
Low tire pressure warning system ...................... WT-8
Low tire pressure warning system - trouble diagnoses
WT-11
Low tire pressure warning system - Wiring diagram .....
WT-11
Lubricant (R134a) A/C ..................................... ATC-22
Lubricants .......................................................... MA-11
Lubrication circuit (engine) .................................. LU-5
Lubrication oil A/C ........................................... ATC-22
Lubrication-locks, hinges and hood latches ....... MA-31