2005 INFINITI FX35 flat tire

AV-3
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
HISTORY OF ERRORS ...................................
. 136
DIAGNOSIS BY HISTORY OF ERRORS ........ . 137
NAVIGATION ................................................... . 138
CAN Diag Support Monitor .................................. . 140
OPERATION PROCEDURE ............................ . 140
A/C and AV Switch Self-Diagnosis Function ....... . 141
DESCRIPTION ................................................. . 141
Power Supply and Ground Circuit Check for NAVI
Control Unit ......................................................... . 142
Power Supply and Ground Circuit Check for Display
Control Unit ......................................................... . 143
Power Supply and Ground Circuit Check for Display . 144
Power Supply and Ground Circuit Check for A/C and
AV Switch ............................................................ . 145
Vehicle Speed Signal Check for NAVI Control Unit . 145
Vehicle Speed Signal Check for Display Control Unit . 146
Illumination Signal Check for NAVI Control Unit .. . 147
Illumination Signal Check for Display Control Unit . 148
Ignition Signal Check for NAVI Control Unit ........ . 148
Ignition Signal Check for Display Control Unit .... . 148
Reverse Signal Check for NAVI Control Unit ...... . 148
Reverse Signal Check for Display Control Unit ... . 149
AV Communication Line Check (Between Display
Control Unit and NAVI Control Unit) .................... . 149
Audio Communication Line Check (Between Dis-
play Control Unit and Audio Unit) ........................ . 150
Display Communication Line Check (Between Dis-
play Control Unit and Display) ............................. . 152
AV Communication Line Check (Between Display
Control Unit and A/C and AV Switch) .................. . 154
CAN Communication Line Check ........................ . 155
If NAVI Control Unit Detects That DVD-ROM Map
Is Not Inserted ..................................................... . 155
If NAVI Control Unit Detects That Inserted DVD-
ROM Map Malfunctioning Or If It Is Impossible to
Load Data from DVD-ROM Map ......................... . 155
If Connection Between NAVI Control Unit and GPS
AntennaIs Malfunctioning .................................... . 156
RGB Screen Is Not Shown .................................. . 156
Color of RGB Image Is Not Proper (NAVI Screen
Looks Bluish) ....................................................... . 157
Color of RGB Image Is Not Proper (NAVI Screen
Looks Reddish) ................................................... . 158
Color of RGB Image Is Not Proper (NAVI Screen
Looks Yellowish) .................................................. . 159
Color of RGB Image Is Not Proper (All Screens
Looks Bluish) ....................................................... . 160
Color of RGB ImageIs Not Proper (All Screens
Looks Reddish) ................................................... . 161
Color of RGB Image Is Not Proper (All Screens
Looks Yellowish) .................................................. . 162
RGB Screen Is Rolling (NAVI Screen) ................ . 163
RGB Screen Is Rolling (Excepting NAVI Screen) . 164
Guide Sound Is Not Heard .................................. . 165
Screen Is Not Shown .......................................... . 166
Audio Screen Is Not Shown (NAVI Screen Is Shown) . 166
A/C Screen Is Not Shown (NAVI Screen Is Shown) . 166
TRIP, FUEL ECON and MAINTENANCE Screens
Are Not Shown .................................................... . 166 Average Fuel Economy Displayed Is Not Shown . 167
Driving Distance or Average Speed Displayed Is Not
Shown .................................................................. .167
WARNING DOOR OPEN Screen Is Not Shown .. .168
Tire Pressure Is Not Displayed ............................ .168
Unable to Operate All of A/C and AV Switch (Unable
to Start Self-Diagnosis) ........................................ .168
Navigation System Does Not Activate ................. .169
Position of Current-Location Mark Is Not Correct . 169
Driving Test .......................................................... .170
Example of Symptoms Judged Not Malfunction .. .171
BASIC OPERATION ......................................... .171
VEHICLE MARK ............................................... .171
DESTINATION, PASSING POINTS, AND MENU
ITEMS CANNOT BE SELECTED/SET ............. .172
VOICE GUIDE .................................................. .172
ROUTE SEARCH ............................................. .172
EXAMPLES OF CURRENT-LOCATION MARK
DISPLACEMENT ............................................. .174
CURRENT LOCATION MARK SHOWS A POSI-
TION WHICH IS COMPLETELY WRONG ....... .177
CURRENT-LOCATION MARK JUMPS ............ .177
CURRENT LOCATION MARK IS IN A RIVER OR
SEA .................................................................. .178
WHEN DRIVING ON SAME ROAD, SOME-
TIMES CURRENT-LOCATION MARK IS IN
RIGHT PLACE AND SOMETIMES IT IS WRONG
PLACE .............................................................. .178
LOCATION CORRECTION BY MAP-MATCH-
ING IS SLOW ................................................... .178
ALTHOUGH GPS RECEIVING DISPLAY IS
GREEN, VEHICLE MARK DOES NOT RETURN
TO CORRECT LOCATION ............................... .178
NAME OF CURRENT PLACE IS NOT DIS-
PLAYED ............................................................ .178
CONTENTS OF DISPLAY DIFFER FOR BIRD-
VIEW™ AND THE (FLAT) MAP SCREEN ....... .178
Program Loading of NAVI Control Unit ................ .179
Removal and Installation of NAVI Control Unit .... .180
REMOVAL ........................................................ .180
INSTALLATION ................................................ .180
Removal and Installation of GPS Antenna .......... .180
REMOVAL ........................................................ .180
INSTALLATION ................................................ .180
Removal and Installation of A/C and AV Switch .. .181
Removal and Installation of Display Unit ............. .181
Removal and Installation of Display Control Unit . 181 REMOVAL ........................................................ .181
INSTALLATION ................................................ .181
INFINITI MOBILE ENTERTAINMENT SYSTEM .... .182
System Description .............................................. .182
Component Parts and Harness Connector Location .183
Wiring Diagram – MES – ..................................... .184
Terminals and Reference Value for DVD Player .. .186
Terminals and Reference Value for DVD Display . 187
DVD Player Does Not Work ................................ .189
Screen Is Not Shown (While Sounds Come Out of
an Audio Speaker, Did Not Do of a Head Phone) .191
Screen Is not Shown (Sounds Come Out of Both

INTEGRATED DISPLAY SYSTEM AV-59
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
MAINT Switch (Maintenance Switch)

When “MAINT” switch is pressed, display vehicle information screen. As vehicle information, it indicates
engine oil, tire rotation, tire pressure.

Pressing “MAINT” switch once cycles display from engine oil →tire rotation →tire pressure →display
OFF →engine oil.
Engine Oil and Tire Rotation

Operating the joystick left/right, replace distance can be set.

When journey distance is the same as replace distance, alert is
displayed. (SERVICE ALERT setting is ON.)

Selected replace distance is 0 - 7,500 miles (0 - 12,000 km) in
increments of 500 mile (800 km).

Press and hold “TRIP RESET or MAINT” switch for 1.5 seconds
or longer, reset present journey distance.

During driving, cannot change settings.
Tire Pressure

Tire pressure signal is received from BCM through CAN commu-
nication line.

Tire pressure is displayed.

When FLAT TIRE signal is received from BCM, “FLAT TIRE” is
displayed.
E/M SWITCH
When “E/M” (English/Metric) switch is pressed, change the unit as followings.
SKIA5918E
SKIA5919E
Unit US Mile,
°F, M P G
Metric km, °C, l/100km

NAVIGATION SYSTEM AV-103
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
TIRE PRESSURE

Pressure indication in psi on the screen indicates that the
pressure is being measured. After a few driving trips, the pres-
sures for all four tires will be displayed.

The order of tire pressure figures displayed on the screen does
not correspond with the actual order of the tire position.

Tire pressure rises and falls depending on the heat caused by
the vehicle's traveling condition and the temperature.

FLAT TIRE–very low tire air pressure.
NOTE:

In a case of FLAT TIRE pressure, interrupt screen is not shown
on the display.

On the screen of TIRE PRESSURE, “FLAT TIRE”, “Check”, “All tire” is displayed.
WARNING INDICATIONS
Warning signal (door switch signal) is received from BCM through
CAN communication line.
SKIA5994E
SKIA5995E
Warning
indicators Warning lamps in
instrument panel Warning detection and cancel conditions
Cases of
malfunction
DOOR OPEN Door Detection condition
Vehicle is running [approx. 5km/h (3 MPH) or faster]
and door ajar of any of the doors is detected. Door is open.
Cancel condition Vehicle is stopped and all the doors lock.

BR-28
REAR DISC BRAKE
Revision: 2005 July 2005 FX
INSTALLATION
CAUTION:

Refill with new brake fluid “DOT 3”.

Do not reuse drained brake fluid.
1. Install disc rotor.
2. Install caliper assembly to the vehicle, and tighten bolts to the specified torque. CAUTION:
Before installing caliper assembly to the vehicle, wipe off oil and grease on washer seats on axle
assembly and mounting surface of caliper assembly.
3. Install brake hose to caliper assembly and tighten union bolt to the specified torque.
CAUTION:

Do not reuse copper washer for union bolt.

Securely attach brake hose to protrusion on caliper assembly.
4. Refill new brake fluid and bleed air. Refer to BR-10, "
Bleeding Brake System" .
5. Install tires to the vehicle.
Disassembly and Assembly of Brake Caliper AssemblyAFS001NE
DISASSEMBLY
1. Remove sliding pin bolt, and then remove pad, shim, shim cover, and pad retainer from torque member and cylinder.
2. Remove sliding pin boot from torque member.
3. As shown in the figure, using a flat-bladed screwdriver, remove retaining ring from cylinder body.
4. Place a wooden block as shown in the figure, and blow air from union bolt mounting hole to remove pistons and piston boots.
CAUTION:
Do not get your fingers caught in piston.
5. Using a flat-bladed screwdriver, remove piston seals from cylin- der body.
CAUTION:
Be careful not to damage cylinder inner wall.
SBR028A
BRD0041D
SFIA0999E

PRECAUTIONS BRC-3
[VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
Revision: 2005 July 2005 FX
[VDC/TCS/ABS]PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
AFS00289
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Brake SystemAFS001S3

Recommended fluid is brake fluid “DOT 3”.

Do not reuse drained brake fluid.

Be careful not to splash brake fluid on painted areas such as body. If brake fluid is splashed, wipe it off
and flush area with water immediately.

Do not use mineral oils such as gasoline or kerosene to clean. They will ruin rubber parts and cause
improper operation.

Using a flare nut crowfoot and torque wrench, securely tighten
brake tube flare nuts.

Brake system is an important safety part. If a brake fluid leak is
detected, always disassemble the affected part. If a malfunction
is detected, replace part with a new one.

Before working, turn ignition switch OFF and disconnect electri-
cal connectors of ABS actuator and electric unit (control unit) or
battery negative terminal.

When installing brake piping, be sure to check torque.
WARNING:
Clean brake pads and shoes with a waste cloth, then wipe with
a dust collector.
Precautions for Brake ControlAFS001S4

During VDC/TCS/ABS operation, brake pedal lightly vibrates and a mechanical noise may be heard. This
is normal.

Just after starting vehicle after turning ignition switch ON, brake pedal may vibrate or motor operating
noise may be heard from engine room. This is a normal status of operation check.

Stopping distance may be longer than that of vehicles without ABS when vehicle drives on rough, gravel,
or snow-covered (fresh, deep snow) roads.

When an error is indicated by ABS or another warning lamp, collect all necessary information from cus-
tomer (what symptoms are present under what conditions) and check for simple causes before starting
diagnostic servicing. Besides electrical system inspection, check booster operation, brake fluid level, and
fluid leaks.

If tire size and type are used in an improper combination, or brake pads are not Genuine NISSAN parts,
stopping distance or steering stability may deteriorate.
SBR686C

ON-VEHICLE SERVICE BRC-7
[VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
Revision: 2005 July 2005 FX
1. Stop vehicle with front wheels in straight-ahead position.
CAUTION:

The work should be done at a horizontal place when vehicle is in the unloaded vehicle condi-
tion.

Keep all tires inflated to correct pressures. Adjust the tire pressure to the specified pressure
value.
2. Connect CONSULT-II and CONSULT-II CONVERTER to data link connector on vehicle, and turn ignition switch ON (do not start engine).
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which performs CAN communication.
3. Touch “ABS”, “WORK SUPPORT” and “DECEL G-SEN CALIBRATION” on CONSULT-II screen in this order. Refer to BRC-26, "
CONSULT-II BASIC OPERATION PROCEDURE" .
4. Touch “START”. CAUTION:
Set vehicle as shown in the display.
5. After approximately 10 seconds, touch “END”. (After approxi- mately 60 seconds, it ends automatically.)
6. Turn ignition switch OFF, then turn it ON again. CAUTION:
Be sure to perform above operation.
7. Run vehicle with front wheels in straight-ahead position, then stop.
8. Select “DATA MONITOR”, “SELECTION FROM MENU”, and “DECEL G-SEN” on CONSULT-II screen. Then make sure “DECEL G-SEN” is within 0 ±0.08 G. If value is
more than specification, repeat steps 3 to 7.
9. Erase memory of ABS actuator and electric unit (control unit) and ECM.
10. Turn ignition switch OFF.
SFIA1162E

DI-86
LANE DEPARTURE WARNING SYSTEM
Revision: 2005 July 2005 FX
Camera Aiming AdjustmentAKS00C7J
OUTLINE
Adjust the camera aiming every time the LDW camera unit is removed or installed.
CAUTION:

Place the vehicle on the level ground when the camera aiming adjustment is operated.

Follow the CONSULT-II when adjusting the camera aiming. (Camera aiming adjustment cannot be
operated without CONSULT-II.)
PREPARATION

Keep all tires inflated to correct pressures. Adjust the tire pressure to the specified pressure value.

There is no-load in vehicle. Check if coolant, engine oil are filled up to correct level and fuel tank is full.

Shift the gear into “P” position and release the parking brake.

Clean the windshield.
NOTE:
Do not place anything reflective on the upper surface of instrument panel.
TARGET SETTING
Preparation Aiming Adjustment Jig
For aiming adjustment, prepare the following jigs and targets.
PKIB4693E

FRONT SUSPENSION ASSEMBLY FSU-7
C
D
F
G H
I
J
K L
M A
B
FSU
Revision: 2005 July 2005 FX
5. Place the dent of alignment gauge onto the projection of center
plate and tightly contact them to measure.
CAUTION:

If camber, caster, or kingpin inclination angle is outside
the standard, check front suspension parts for wear and
damage, and replace suspect parts if necessary.

King pin inclination angle is reference value, no inspec-
tion is required.
Toe-In Inspection
Measure toe-in using the following procedure.
WARNING:

Always perform the following procedure on a flat surface.

Make sure that no person is in front of vehicle before push-
ing it.
1. Bounce front of vehicle up and down to stabilize the posture.
2. Push vehicle straight ahead about 5 m (16 ft).
3. Put a mark on base line of the tread (rear side) of both tires at the same height of hub center. These are measuring points.
4. Measure distance “A” (rear side).
5. Push vehicle slowly ahead to rotate wheels 180 degrees (1/2 turn).
If wheels have rotated more than 180 degrees (1/2 turn), try the
above procedure again from the beginning. Never push vehicle
backward.
6. Measure distance “B” (front side). Camber, caster, kingpin inclination angles:
Refer to FSU-18, "
SERVICE DATA"FSU-18, "SER-
VICE DATA" .
SEIA0241E
SEIA0362E
Total toe-in : Refer to FSU-18, "SERVICE DATA" .
SEIA0363E