2005 INFINITI FX35 shift

AT-90
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
CONSULT-II Function (A/T)ACS002M9
CONSUT-II can display each diagnostic item using the diagnostic test models shown following.
FUNCTION
CONSULT-II REFERENCE VALUE
NOTICE:
1. The CONSULT-II electrically displays shift timing and lock-up timing (that is, operation timing of each sole-
noid).
Check for time difference between actual shift timing and the CONSULT-II display. If the difference is
noticeable, mechanical parts (except solenoids, sensors, etc.) may be malfunctioning. Check mechanical
parts using applicable diagnostic procedures.
2. Shift schedule (which implies gear position) displayed on CONSULT-II and that indicated in Service Man- ual may differ slightly. This occurs because of the following reasons:
–Actual shift schedule has more or less tolerance or allowance,
–Shift schedule indicated in Service Manual refers to the point where shifts start, and
–Gear position displayed on CONSULT-II indicates the point where shifts are completed.
3. Display of solenoid valves on CONSULT-II changes at the start of shifting, while gear position is displayed upon completion of shifting (which is computed by TCM).
Diagnostic test mode Function Reference page
Self-diagnostic results Self-diagnostic results can be read and erased quickly. AT- 9 3
Data monitor Input/Output data in the ECU can be read.AT- 9 6
CAN diagnostic support
monitor The results of transmit/receive diagnosis of CAN communication can be read.
AT- 1 0 0
Function test Performed by CONSULT-II instead of a technician to determine whether each system
is “OK” or “NG”. —
DTC work support Select the operating condition to confirm Diagnosis Trouble Codes. AT- 1 0 0
ECU part number ECU part number can be read. —
Item name Condition Display value
(Approx.)
VHCL/S SE·A/T During driving Approximately
matches the speed-
ometer reading.
VHCL/S SE·MTR
ACCELE POSI Released accelerator pedal. 0.0/8
Fully depressed accelerator pedal. 8/8
CLSD THL POS Released accelerator pedal. ON
Fully depressed accelerator pedal. OFF
W/O THL POS Fully depressed accelerator pedal. ON
Released accelerator pedal. OFF
BRAKE SW Depressed brake pedal. ON
Released brake pedal. OFF
ENGINE SPEED Engine running Closely matches the
tachometer reading.
TURBINE REV During driving (lock-up ON) Approximately
matches the engine
speed.
ATF TEMP SE 1 0 °C (32 ° F) - 20 °C (68 °F) - 80 °C (176 °F) 3.3 - 2.7 - 0.9 V
ATF TEMP SE 2 3.3 - 2.5 - 0.7 V
TCC SOLENOID When performing slip lock-up 0.2 - 0.4 A
When performing lock-up 0.4 - 0.6 A
LINE PRES SOL During driving 0.2 - 0.6 A

TROUBLE DIAGNOSIS AT-91
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
FR/B SOLENOID Front brake engaged. Refer to
AT- 2 1 . 0.6 - 0.8 A
Front brake disengaged. Refer to AT- 2 1
. 0 - 0.05 A
I/C SOLENOID Input clutch disengaged. Refer to
AT- 2 1
. 0.6 - 0.8 A
Input clutch engaged. Refer to AT- 2 1
. 0 - 0.05 A
D/C SOLENOID Direct clutch disengaged. Refer to
AT- 2 1
. 0.6 - 0.8 A
Direct clutch engaged. Refer to AT- 2 1
. 0 - 0.05 A
HLR/C SOL High and low reverse clutch disengaged. Refer to
AT- 2 1
. 0.6 - 0.8 A
High and low reverse clutch engaged. Refer to AT- 2 1
. 0 - 0.05 A
STARTER RELAY Selector lever in “N”, “P” position. ON
Selector lever in other positions. OFF
SLCT LVR POSI Selector lever in “N”,“P” position. N/P
Selector lever in “R” position. R
Selector lever in “D” position. D
ON OFF SOL Low coast brake engaged. Refer to
AT- 2 1
.ON
Low coast brake disengaged. Refer to AT- 2 1
.OFF
ATF PRES SW 1 Front brake engaged. Refer to
AT- 2 1
.ON
Front brake disengaged. Refer to AT- 2 1
.OFF
ATF PRES SW 2 Low coast brake engaged. Refer to
AT- 2 1
.ON
Low coast brake disengaged. Refer to AT- 2 1
.OFF
ATF PRES SW 3 Input clutch engaged. Refer to
AT- 2 1
.ON
Input clutch disengaged. Refer to AT- 2 1
.OFF
ATF PRES SW 5 Direct clutch engaged. Refer to
AT- 2 1
.ON
Direct clutch disengaged. Refer to AT- 2 1
.OFF
ATF PRES SW 6 High and low reverse clutch engaged. Refer to
AT- 2 1
.ON
High and low reverse clutch disengaged Refer to AT- 2 1
.OFF
MANU MODE SW Manual shift gate position (neutral) ON
Other than the above OFF
NON M-MODE SW Manual shift gate position OFF
Other than the above ON
UP SW LEVER Selector lever: + side ON
Other than the above OFF
DOWN SW LEVER Selector lever: - side ON
Other than the above OFF
GEAR During driving 1, 2, 3, 4, 5 Item name Condition
Display value
(Approx.)

AT-94
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
TCM·ROM
TCM memory (ROM) is malfunctioning. P1703 —AT-132
TP SEN/CIRC A/T
TCM does not receive the proper accelerator pedal position sig-
nals (input by CAN communication) from ECM. P1705 P1705*3
AT-133
ATF TEMP SEN/
CIRC
During running, the AT fluid temperature sensor signal voltage is
excessively high or low P1710 P0710
AT-136
TURBINE REV S/
CIRC
TCM does not receive the proper voltage signal from the sensor.

TCM detects an irregularity only at position of 4th gear for turbine
revolution sensor 2. P1716 P1716
AT-141
VEH SPD SE/
CIR·MTR
Signal (CAN communication) from vehicle speed sensor MTR not
input due to cut line or the like

Unexpected signal input during running P1721 —
AT-143
A/T INTERLOCK
Except during shift change, the gear position and ATF pressure
switch states are monitored and comparative judgement made. P1730 P1730
AT-145
A/T 1ST E/BRAK-
ING
Each ATF pressure switch and solenoid current is monitored and
if a pattern is detected having engine braking 1st gear other than
in the M1 position, a malfunction is detected. P1731 —
AT-148
I/C SOLENOID/
CIRC

Normal voltage not applied to solenoid due to functional malfunc-
tion, cut line, short, or the like

TCM detects as irregular by comparing target value with monitor
value. P1752 P1752
AT-150
I/C SOLENOID
FNCTN

TCM detects that actual gear ratio is irregular, and relation
between gear position and condition of ATF pressure switch 3 is
irregular during depressing accelerator pedal. (Other than during
shift change)

TCM detects that relation between gear position and condition of
ATF pressure switch 3 is irregular during releasing accelerator
pedal. (Other than during shift change) P1754 P1754*2
AT-152
FR/B SOLENOID/
CIRC

Normal voltage not applied to solenoid due to functional malfunc-
tion, cut line, short, or the like

TCM detects as irregular by comparing target value with monitor
value. P1757 P1757
AT-154
FR/B SOLENOID
FNCT

TCM detects that actual gear ratio is irregular, and relation
between gear position and condition of ATF pressure switch 1 is
irregular during depressing accelerator pedal. (Other than during
shift change)

TCM detects that relation between gear position and condition of
ATF pressure switch 1 is irregular during releasing accelerator
pedal. (Other than during shift change) P1759 P1759*2
AT-156
D/C SOLENOID/
CIRC

Normal voltage not applied to solenoid due to cut line, short, or
the like

TCM detects as irregular by comparing target value with monitor
value. P1762 P1762
AT-158
Items (CONSULT-II
screen terms) Malfunction is detected when... TCM self-
diagnosis OBD-II
(DTC)
Reference page
“A/T” with
CONSULT- II MIL indica-
tor lamp*1, “ENGINE”
with CON- SULT-II or GST

TROUBLE DIAGNOSIS AT-95
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
*1: Refer to AT- 4 2 , "Malfunction Indicator Lamp (MIL)" .
*2: These malfunctions cannot be displayed MIL if another malfunction is assigned to MIL. D/C SOLENOID
FNCTN

TCM detects that actual gear ratio is irregular, and relation
between gear position and condition of ATF pressure switch 5 is
irregular during depressing accelerator pedal. (Other than during
shift change)

TCM detects that relation between gear position and condition of
ATF pressure switch 5 is irregular during releasing accelerator
pedal. (Other than during shift change) P1764 P1764*2
AT- 1 6 0
HLR/C SOL/CIRC

Normal voltage not applied to solenoid due to functional malfunc-
tion, cut line, short, or the like

TCM detects as irregular by comparing target value with monitor
value. P1767 P1767
AT- 1 6 2
HLR/C SOL
FNCTN

TCM detects that actual gear ratio is irregular, and relation
between gear position and condition of ATF pressure switch 6 is
irregular during depressing accelerator pedal. (Other than during
shift change)

TCM detects that relation between gear position and condition of
ATF pressure switch 6 is irregular during releasing accelerator
pedal. (Other than during shift change) P1769 P1769*2
AT- 1 6 4
LC/B SOLENOID/
CIRC
Normal voltage not applied to solenoid due to functional malfunc-
tion, cut line, short, or the like P1772 P1772
AT- 1 6 6
LC/B SOLENOID
FNCT

TCM detects an improper voltage drop when it tries to operate
the solenoid valve.

Condition of ATF pressure switch 2 is different from monitor
value, and relation between gear position and actual gear ratio is
irregular. P1774 P1774*2
AT- 1 6 8
MANU MODE SW/
CIRC
When an impossible pattern of switch signals is detected, a mal-
function is detected. P1815 —
AT- 1 7 0
ATF PRES SW 1/
CIRC

TCM detects that actual gear ratio is normal, and relation
between gear position and condition of ATF pressure switch 1 is
irregular during depressing accelerator pedal. (Other than during
shift change) P1841 —
AT- 1 7 5
ATF PRES SW 3/
CIRC

TCM detects that actual gear ratio is normal, and relation
between gear position and condition of ATF pressure switch 3 is
irregular during depressing accelerator pedal. (Other than during
shift change) P1843 —
AT- 1 7 7
ATF PRES SW 5/
CIRC

TCM detects that actual gear ratio is normal, and relation
between gear position and condition of ATF pressure switch 5 is
irregular during depressing accelerator pedal. (Other than during
shift change) P1845 —
AT- 1 7 9
ATF PRES SW 6/
CIRC

TCM detects that actual gear ratio is normal, and relation
between gear position and condition of ATF pressure switch 6 is
irregular during depressing accelerator pedal. (Other than during
shift change) P1846 —
AT- 1 8 1
NO DTC IS
DETECTED FUR-
THER TESTING
MAY BE
REQUIRED

No NG item has been detected. X X —
Items (CONSULT-II
screen terms) Malfunction is detected when... TCM self-
diagnosis OBD-II
(DTC)
Reference page
“A/T” with
CONSULT- II MIL indica-
tor lamp*1, “ENGINE”
with CON- SULT-II or GST

TROUBLE DIAGNOSIS AT-97
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
THROTTLE POSI (0.0/8) X X Degree of opening for accelerator recognized by
the TCM
For fail-safe operation, the specific value used
for control is displayed.
CLSD THL POS (ON-OFF) X — Signal input with CAN communications
W/O THL POS (ON-OFF) X —
BRAKE SW (ON-OFF) X — Stop lamp switch
GEAR — X Gear position recognized by the TCM updated
after gear-shifting
ENGINE SPEED (rpm) X X
TURBINE REV (rpm) X X
OUTPUT REV (rpm) X X
GEAR RATIO — X
TC SLIP SPEED (rpm) — X Difference between engine speed and torque
converter input shaft speed
F SUN GR REV (rpm) — —
F CARR GR REV (rpm) — —
ATF TEMP SE 1 (V) X —
ATF TEMP SE 2 (V) X —
AT F T E M P 1 ( °C) — X
AT F T E M P 2 ( °C) — X
BATTERY VOLT (V) X —
ATF PRES SW 1 (ON-OFF) X X (for FR/B solenoid)
ATF PRES SW 2 (ON-OFF) X X (for LC/B solenoid)
ATF PRES SW 3 (ON-OFF) X X (for I/C solenoid)
ATF PRES SW 5 (ON-OFF) X X (for D/C solenoid)
ATF PRES SW 6 (ON-OFF) X X (for HLR/C solenoid)
PNP SW 1 (ON-OFF) X —
PNP SW 2 (ON-OFF) X —
PNP SW 3 (ON-OFF) X —
PNP SW 4 (ON-OFF) X —
1 POSITION SW (ON-OFF) X —
SLCT LVR POSI — X Selector lever position is recognized by the
TCM.
For fail-safe operation, the specific value used
for control is displayed.
OD CONT SW (ON-OFF) X —
Not mounted but displayed.
POWERSHIFT SW (ON-OFF) X —
HOLD SW (ON-OFF) X — Monitored item (Unit)
Select Monitor Item
Remarks
ECU
INPUT
SIGNALS MAIN SIG-
NALS SELEC-
TION
FROM
MENU

TROUBLE DIAGNOSIS AT-99
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
1ST POSI IND (ON-OFF) — —
MANU MODE IND (ON-OFF) — —
POWER M LAMP (ON-OFF) — —
F-SAFE IND/L (ON-OFF) — —
ATF WARN LAMP (ON-OFF) — — Not mounted but displayed
BACK-UP LAMP (ON-OFF) — —
STARTER RELAY (ON-OFF) — —
PNP SW3 MON (ON-OFF) — —
C/V CLB ID1 — —
C/V CLB ID2 — —
C/V CLB ID3 — —
UNIT CLB ID1 — —
UNIT CLB ID2 — —
UNIT CLB ID3 — —
TRGT GR RATIO — —
TRGT PRES TCC (kPa) — —
TRGT PRES L/P (kPa) — —
TRGT PRES I/C (kPa) — —
TRGT PRE FR/B (kPa) — —
TRGT PRES D/C (kPa) — —
TRG PRE HLR/C (kPa) — —
SHIFT PATTERN — —
DRV CST JUDGE — —
START RLY MON — —
NEXT GR POSI — —
SHIFT MODE — —
MANU GR POSI — —
VEHICLE SPEED (km/h) — X Vehicle speed recognized by the TCM.
Voltage (V) — — Displays the value measured by the voltage
probe.
Frequency (Hz) — —
The value measured by the pulse probe is dis-
played.
DUTY-HI (high) (%) — —
DUTY-LOW (low) (%) — —
PLS WIDTH-HI (ms) — —
PLS WIDTH-LOW (ms) — — Monitored item (Unit)
Select Monitor Item
Remarks
ECU
INPUT
SIGNALS MAIN SIG-
NALS SELEC-
TION
FROM
MENU

AT-102
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
7. Perform test drive to check gear shift feeling in accordance with
instructions displayed.
8. Touch “YES” or “NO”.
9. CONSULT-II procedure is ended.

If “NG” appears on the screen, a malfunction may exit.
Go to “Diagnostic Procedure”
Display Items List
*: Do not use, but displayed.
SCIA5163E
SCIA5162E
DTC work support item Description Check item
I/C SOL FUNCTN CHECK* — —
FR/B SOL FUNCTN CHECK* — —
D/C SOL FUNCTN CHECK* — —
HLR/C SOL FUNCTN CHECK* — —
LC/B SOL FUNCTN CHECK* — —
TCC SOL FUNCTN CHECK Following items for “TCC solenoid function (lock-up) ” can be con-
firmed.

Self-diagnosis status (whether the diagnosis is being performed
or not)

Self-diagnosis results (OK or NG)

TCC solenoid valve

Hydraulic control circuit

TROUBLE DIAGNOSIS AT-103
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
Diagnostic Procedure without CONSULT-IIACS008CZ
OBD-II SELF-DIAGNOSTIC PROCEDURE (WITH GST)
Refer to EC-144, "Generic Scan Tool (GST) Function" (for VQ35DE) or EC-835, "Generic Scan Tool (GST)
Function" (for VK45DE).
OBD-II SELF-DIAGNOSTIC PROCEDURE (NO TOOLS)
Refer to EC-69, "Malfunction Indicator Lamp (MIL)" (for VQ35DE) or EC-760, "Malfunction Indicator Lamp
(MIL)" (for VK45DE).
TCM SELF-DIAGNOSTIC PROCEDURE (NO TOOLS)
Description
In the unlikely event of a malfunction in the electrical system, when the ignition switch is switched “ON”, the A/
T CHECK indicator lamp lights up for 2 seconds, then flashes for 8 seconds. If there is no malfunction, when
the ignition switch is turned “ON”, the indicator lamp lights up for 2 seconds. As a method for locating the sus-
pect circuit, when the self-diagnostics start signal is input, the memory for the malfunction location is output
and the A/T CHECK indicator lamp flashes to display the corresponding DTC.
Diagnostic Procedure
1. CHECK A/T CHECK INDICATOR LAMP
1. Start the engine with selector lever in “P” position. Warm engine to normal operating temperature.
2. Turn ignition switch “ON” and “OFF” at least twice, then leave it in the “OFF” position.
3. Wait 10 seconds.
4. Turn ignition switch “ON”. (Do not start engine.)
Does A/T CHECK indicator lamp come on for about 2 seconds?
YES >> GO TO 2.
NO >> GO TO AT- 1 9 3
.
2. JUDGEMENT PROCEDURE STEP 1
1. Turn ignition switch “OFF”.
2. Push shift lock release button.
3. Move selector lever from “P” to “D” position.
4. Release accelerator pedal. (Set the closed throttle position signal “ON”.)
5. Depress brake pedal. (Stop lamp switch signal “ON”.)
6. Turn ignition switch “ON”. (Do not start engine.)
7. Wait 3 seconds.
>> GO TO 3.
3. JUDGEMENT PROCEDURE STEP 2
1. Move the selector lever to the manual shift gate side. (Manual mode switch “ON”.)
2. Release brake pedal. (Stop lamp switch signal “OFF”.)
3. Move the selector lever to “D” position. (Manual mode switch “OFF”.)
4. Depress brake pedal. (Stop lamp switch signal “ON”.)
5. Release brake pedal. (Stop lamp switch signal “OFF”.)
6. Depress accelerator pedal fully and release it.
>> GO TO 4.