2005 HYUNDAI XG350 lock

1FEATURES OF YOUR HYUNDAI8
B070E02HP-GATReplacing the batteryWhen the transmitter's battery begins to get
weak, it may take several pushes on the button
to lock or unlock the doors, and the LED will not
light. Replace the battery as soon as possible.
Battery type : CR2032
Replacement instructions:
1. Carefully separate the case with a blade
screwdriver as shown in the illustration.
HEF-192A
Screwdriver
CAUTION:
Only the transmitter can disarm the armed
stage. If the transmitter does not disarm the
system, it is necessary to take the following
steps;
1. Unlock the door with the key, which will
cause the alarm to be activated.
2. Insert the key in the ignition key cylinder
and turn the ignition key to "ON" posi-
tion.
3. Wait for 30 seconds.
After completing the steps above, the sys-
tem will be disarmed.
!
HXG117
UNLOCK
LOCK
TRUNK
B070D04L-AATDisarmed StageThe system will be disarmed when the following
step is taken:
The driver's or passenger's door is unlocked by
depressing the " " button on the transmitter.
After completion of the steps above, the turn
signal lights will blink twice to indicate that the
system is disarmed.
xgflhma-1.p656/16/04, 3:02 PM 8

1
FEATURES OF YOUR HYUNDAI
9
2. Remove the old battery from the case and
note the polarity. Make sure the polarity of
the new battery is the same(+side facing
down), then insert it in the transmitter.
HEF-193
Battery
POWER WINDOWSB060A03Y-AATThe power windows operate when the ignition
key is in the "ON" position. The main switches
are located on the driver's armrest and control
the front and rear windows on both sides of the
vehicle. The windows may be opened by de-
pressing the appropriate window switch and
closed by pulling up the switch. To open the
window on the driver's side, press the switch(1)
halfway down. The window moves as long as
the switch is operated. To fully open the driver's
window automatically, press the switch fully
down. In automatic operation, the window will
fully open even if you let go of the switch. To stop
at the desired opening, pull up and release the
switch.In order to prevent operation of the passanger
front and rear windows, a window lock switch(2)
is provided on the armrest of the driver's door.
To disable the power windows, press the win-
dow lock switch. To return to normal operation,
press the window lock switch a second time.
NOTE:The power windows can be operated for 30
seconds after the ignition key is turned to
the "ACC" or "LOCK" positions, or removed
from the ignition switch.
If the front doors are opened during this 30
second period, the power windows can no
longer be operated without the ignition key
turned to the "ON" position.
HXG129-1
OpenClose
HXG025-1
(1)
(2)
xgflhma-1.p656/16/04, 3:02 PM 9

1FEATURES OF YOUR HYUNDAI10
SEATS!
B080A01A-AATADJUSTABLE FRONT SEATS
WARNING:Never attempt to adjust the seat while the
vehicle is moving. This could result in loss
of control or an accident which may cause
death, serious injury, or property damage.
B080B01L-AATAdjusting Seat Forward and RearwardTo move the seat toward the front or rear, pull
the lock release lever upward. This will release
the seat on its track so you can move it forward
or rearward to the desired position. When you
find the position you want, release the lever and
slide the seat forward or rearward on its track
until it locks into the desired position and cannot
be moved further.
HXG179
!
WARNING:
To ensure the seat is locked securely, at-
tempt to move the seat forward or rearward
without using the control knob.
!
WARNING:
(1) Be careful that someone's head, hands
and body are not trapped by a closing
window.
(2) Never try to operate the main switch on
the driver's door and the individual door
window switch in opposing directions
at the same time. If this is done, the
window will stop and cannot be opened
or closed.
(3) Do not leave children alone in the car.
Always remove the ignition key for their
safety.
HXG029
Close
Open
xgflhma-1.p656/16/04, 3:02 PM 10

1
FEATURES OF YOUR HYUNDAI
11
!
HXG103 B080C02A-AAT
Adjusting Seatback AngleTo recline the seatback, lean forward to take
your weight off it, then pull up on the recliner
control lever at the outside edge of the seat. Now
lean back until the desired seatback angle is
achieved. To lock the seatback into position,
release the recliner control lever.
WARNING:
To minimize risk of severe injury in the
event of a collision or a sudden stop, both
the driver and passenger seatbacks should
always be in an upright position while the
vehicle is in motion. The protection pro-
vided by the seat belts and airbags in a
frontal collision may be reduced signifi-
cantly when the seatbacks are reclined.
There is greater risk that the driver and
passenger will slide under the seat belt
which may result in serious injury if a crash
occurs when the seatbacks are reclined.
The seat belt and airbags cannot provide
proper protection to an occupant if the seat
back is reclined.
B080D01L-GATAdjustable HeadrestsHeadrests are designed to help reduce the risk
of neck injuries.
To raise the headrest, pull it up. To lower it, push
it down while pressing the lock knob. If equipped
with a horizontally adjustable type of headrest,
pull on the top.
HXG200J
Lock Knob
xgflhma-1.p656/16/04, 3:02 PM 11

1
FEATURES OF YOUR HYUNDAI
15
Reverse Parking Aid FunctionWhen the "AUTO" button is "ON" and the
vehicle is moving backward, the outside rear-
view mirror(s) will move downward to aid re-
verse parking safely. According to the position
of the outside rearview mirror switch knob, the
outside rearview mirror(s) will operate as fol-
lows.
L: When the remote control outside rearview
mirror switch knob is selected to the "L"
position, both of the outside rearview mir-
rors will move downward.
R: When the remote control outside rearview
mirror switch knob is selected to the "R"
position, only the passenger's outside rear-
view mirror will move downward.
Neutral: When the remote control outside rear-
view mirror switch knob is placed in
the middle position, the outside rear-
view mirrors will not operate while the
vehicle is moving backward.NOTE:When the ignition key is in the "LOCK"
position, the selector lever is moved to any
position except "R" position, or the remote
control outside rearview mirror switch knob
is placed in the middle position, the outside
rearview mirrors will automatically revert to
original position.
!
CAUTION:
In the following conditions, the I.M.S will
not operate.
1. When the "1" or "2" button is not pushed
within five seconds.
2. When the seat is being adjusted.
3. When the "STOP" button is pushed.
4. While the vehicle is moving.To activate the memorized positionWhen you push button "1" or "2", the driving
position will be automatically adjusted to the
position recorded for that button.To memorize driving position1. Turn the ignition key "ON".
2. Adjust the driver's seat and outside rearview
mirrors to the desired position.
3. Push the "M" button on the I.M.S until the
signal beeps.
4. Within five seconds, push button "1" or "2"
until the signal beeps twice. The beep sounds
mean that the positions are memorized in the
I.M.S.
"AUTO" button functionWhen the "AUTO" button is "ON", the system
will move the driver's seat forward or rearward
so you can comfortably enter and exit the
vehicle.
o It will move driver's seat rearward when the
ignition key is pulled out.
o It will move driver's seat forward when the
ignition key is inserted.Note:In order for the "AUTO" functions to work,
the parking brake must be applied.
CAUTION:
In the following conditions, the "AUTO"
mode will not operate.
1. When AUTO button is in "OFF".
2. When the seat is being adjusted.
3. When the shift lever is positioned in
other than "P" position.
!
xgflhma-1.p656/16/04, 3:02 PM 15

1FEATURES OF YOUR HYUNDAI16
!
FOLDING REAR SEATBACKS
SEAT WARMERB100A02Y-AAT(If Installed)The seat warmer is provided to warm the front
seats during cold weather. With the ignition key
in the "ON" position, push either of the switches
to warm the driver's seat or the passenger's
seat.
During mild weather or under conditions where
the operation of the seat warmer is not needed,
keep the switches in the "OFF" position.
Driver's seat
HXG620
Passenger's seat
B110A01L-A B110A01L-AAT
o To unlock the seatback, depress the
seatback locking button, then pull forward on
the seatback panel.
o When you return the seatback to its upright
position, always be sure it has locked into
position by pulling and pushing on the top of
the seatback.
!
WARNING:
The purpose of the folding rear seatbacks
is to allow you to carry longer objects than
could otherwise be accommodated. Never
allow passengers to sit on top of the folded
down seatback. While the car is moving as
this is not a proper seating position and no
seat belts are available for use. This could
result in serious injury or death in case of an
accident or sudden stop. Objects carried
on the folded down seatback should not
extend higher than the top of the front
seats. This could allow cargo to slide for-
ward and cause injury or damage during
sudden stops.
B110A02L-A
WARNING:
It is recommended that the seat heater not
be used when elderly people or people who
are ill occupy the seat. Also, do not use the
seat warmer if the occupant is sleeping.
xgflhma-1.p656/16/04, 3:02 PM 16

1
FEATURES OF YOUR HYUNDAI
17
SEAT BELT!
B150A02A-AATSEAT BELT PRECAUTIONS
WARNING:All occupants of the vehicle must wear their
seat belts at all times. Note that this vehicle
is equipped with a Supplemental Restraint
(Airbag) System as discussed beginning
on page 1-31. The seat belts must be used
in conjunction with the supplemental
airbag system. State laws require that some
or all occupants of the vehicle use seat
belts. The possibility of increased injury or
severity of injury in an accident will be
increased if this elementary safety precau-
tion is not observed.
B120A01Y-AATREAR SEATBACK SAFETY LOCK
(If Installed)If the rear seatback lock lever (located on the
backside of the rear seatback) is in the "LOCK"
position when the rear seatbacks are closed, it
will not be possible to fold the rear seatback by
using the release lock lever. In this instance,
move the lock lever to the "FREE" position and
fold the rear seatback. The rear seatback lock
lever is designed to provide protection from
unauthorized entry into the trunk.
FREE
LOCK
B120A03L
B140A03L B140A01S-AAT
REAR SEAT WARNINGFor the safety of all passengers, luggage or
other cargo should not be piled higher than the
top of the seatback. In addition, do not place
objects on the rear shelf as they may move
forward during braking or in an accident and
strike vehicle passengers.
!
xgflhma-1.p656/16/04, 3:02 PM 17

1FEATURES OF YOUR HYUNDAI20
!
B170A01L-GATHEIGHT ADJUSTABLE FRONT SEAT
SHOULDER BELT
B170A01L
You can adjust the height of the shoulder belt
anchor to one of the 4 positions for maximum
comfort and safety.
If the height of the adjusting seat belt is too near
your neck, you will not be getting the most
effective protection. The shoulder portion should
be adjusted so that it lies across your chest and
midway over your shoulder nearest the door
and not your neck.
To adjust the height of the seat belt anchor,
lower or raise the height adjuster into an appro-
priate position. To raise the height adjuster, pull
it up. To lower it, push it down while pressing the
height adjuster button.
WARNING:
o The height adjuster must be in the locked
position when the vehicle is moving.
o The misadjustment of height of the
shoulder belt could reduce the effective-
ness of the seat belt in a crash.
B180A01L-AATSEAT BELT-Driver's 3-Point System with
Emergency Locking Retractor:
To Fasten Your BeltTo fasten your seat belt, pull it out of the retractor
and insert the metal tab into the buckle. There
will be an audible "click" when the tab locks into
the buckle.
The seat belt automatically adjusts to the proper
length only after the lap belt portion is adjusted
manually so that it fits snugly around your hips.
If you lean forward in a slow, easy motion, the
belt will extend and let you move around. If there
is a sudden stop or impact, however, the belt will
lock into position. It will also lock if you try to lean
forward too quickly.
B180A01L
Release the button to lock the anchor into
position. Try sliding the height adjuster to make
sure that it has locked into the position.
xgflhma-1.p656/16/04, 3:02 PM 20