2005 DODGE DAKOTA Owners Manual

contain “Mini”fuses and plug-in “ISO” relays. A label
inside the latching cover of the Power Distribution Cen-
ters identifies each component for ease of replacement, if
necessary. These fuses and relays can be obtained from
your dealer.
CAUTION!
When replacing a blown fuse, it is important to use
only a fuse having the correct amperage rating. The
use of a fuse with a rating other than indicated may
result in a dangerous electrical system overload. If a
properly rated fuse continues to blow, it suggests a
problem in the circuit that must be corrected.
NOTE:If you are leaving your vehicle dormant for
longer than 21 days you may want to take steps to protect
your battery. You may do this by disconnecting the
battery or by disconnecting the two ignition-off draw
(I.O.D.) fuses located in the Auxiliary Power DistributionCenter (PDC) located in the engine compartment. The
I.O.D. cavities include a snap-in retainer that allows the
fuse to be disconnected, without removing it from the
fuse block. Pressing the I.O.D. fuse back into the cavity
reconnects it.
VEHICLE STORAGE
If you are storing your vehicle for more than 21 days, we
recommend that you take the following steps to mini-
mize the drain on your vehicle’s battery:
•Disconnect the Ignition-Off Draw fuse (I.O.D.) fuse
located in the Power Distribution Center (PDC). The
I.O.D. cavity includes a snap-in retainer that allows the
fuse to be disconnected, without removing it from the
fuse block.
•The transfer case should be placed in the 4HI mode
and kept in this position to minimize the battery drain.
•As an alternative to the above steps you may discon-
nect the negative cable from the battery.
MAINTAINING YOUR VEHICLE 329
7

REPLACEMENT LIGHT BULBS
LIGHT BULBS — Interior Bulb No.
Dome Light........................WL212–2
Cargo Light............................ 567
Overhead Console Lights................... 192
Reading Light.......................WL212–2
LIGHT BULBS — Outside Bulb No.
Headlight............................. H13
Front Park/Turn/Sidemarker.............3157NA
Back-Up..............................3157
Center High Mounted Stoplight.............. 921
Fog Lamp.............................9145
Rear Sidemarker......................... 168
License Plate Light....................... 168
Rear Tail, Stop, Turn Signal.................3057
BULB REPLACEMENT
Headlamps
Removing Attaching Screw
330 MAINTAINING YOUR VEHICLE

1. Open the hood.
2. Remove the 3 screws attaching the headlamp housing
to the inner panel.
3. Grasp the headlamp and pull firmly to disengage the
headlamp housing from the fender panel.
Removing Headlamp AssemblyRemoving Headlamp Assembly
MAINTAINING YOUR VEHICLE 331
7

4. While firmly holding the headlamp housing in your
hands unlock and disconnect Headlamp bulb connector.
5. Twist 1/4 turn and remove Headlamp bulb from
housing and replace.
6. Twist 1/4 turn and remove bulb and socket from
housing, pull bulb straight out from socket and replace.
Removing Headlamp Bulb
Unlocking Connector
332 MAINTAINING YOUR VEHICLE

Removing Headlamp from AssemblyRemoving Headlamp Bulb
MAINTAINING YOUR VEHICLE 333
7

7. Reverse procedure to install new Headlamp bulb into
the headlamp assembly.
NOTE:These are Halogen bulbs. Take care not to touch
the bulb with your fingers. Body oils from your fingers
could cause excessive heat buildup which reduces bulb
life.
Front Park and Turn Signal Lamp.
•
Open the hood.
•Remove the (3) screws attaching the headlamp hous-
ing to the inner panel.
•Grasp the headlamp and pull firmly to disengage the
headlamp housing from the fender panel.
NOTE:It is not necessary to disconnect the connector to
replace this bulb. If the bulb socket needs replacement
disconnect the connector.
Disconnecting Headlamp Bulb Connector
334 MAINTAINING YOUR VEHICLE

•Rotate bulb socket 1/4 turn and remove socket from
housing.
•Pull bulb straight from socket.
•Reverse procedure to install new turn signal bulb.
Removing Turn Signal BulbDisconnecting Turn Signal Connector
MAINTAINING YOUR VEHICLE 335
7

Rear Side Marker, Taillamps/Stoplamp, and Turn
Signal Bulbs — Replacement
1. Remove the two (2) screws that pass through the bed
sheetmetal.
2. Pull the taillamp housing straight out from the body.
Removing the Two (2) Screws
Pulling Housing From Body
336 MAINTAINING YOUR VEHICLE