2005 Citroen XSARA PICASSO Turn

Downloaded from www.Manualslib.com manuals search engine 188
ENGINECHECKING THE VALVE TIMING
Engine: KFU
Tools.
[1] Flywheel setting peg: 4507-TA. Toolkit 4507-T
[2] Camshaft setting peg: 4533-TA.C1
[3] Camshaft setting peg: (-).0194.A
IMPERATIVE: Respect the safety and cleanliness requirements.
Checking.
Deconnect the battery.
Remove:
- The engine cover.
- The upper timing cover (1).
- The oil filter (2).
Remove the sparking plugs to facilitate rotation of the engine.
Turn the engine by means of the crankshaft screw.
IMPERATIVE: Never turn the engine backwards.
Suspend the engine.
Remove:
- The screws (3), the upper RH engine support (4)and the screws (5).
B1BP37JC
B1BP37KC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 188

Downloaded from www.Manualslib.com manuals search engine 191
ENGINE
191
CHECKING AND SETTING THE VALVE TIMING
Engine: KFU
Setting the timing (continued).
Rotate the engine by means of the crankshaft screw
(clockwise), to bring it to the pegging position.
Peg the flywheel, using tool [1].
Position the tools [2]and [3].
Remove the engine support assembly (9), the fixing
screw (8)and the lower cover (7).
Slacken the nut (11).
Fully detension the belt by moving the tensioner
roller (10).
Remove the timing belt.
IMPERATIVE: Check that the tensioner roller
turns freely
(no tight spot).
Refitting.
Position the
(new)timing belt, in the following
sequence:
- The inlet camshaft pulley, the exhaust camshaft
pulley, the guide roller, the crankshaft pulley, position
the tool [4], the coolant pump pulley, the dynamic
tensioner roller.
Remove the tools [1], [2], [3]and [4].
B1BP2MBC
B1BP2ZMC
B1CP0GLD
B1CP0GMD
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 191

Downloaded from www.Manualslib.com manuals search engine 192
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: KFU
Overtension on the belt.
Position «a»: Tensioner roller in detensionedposition.
Position «b»: Tensioner roller in normalposition.
Position «c»: Tensioner roller in overtensionposition.
Turn the tensioner roller (10), using an allen spanner at «e».
Place the index «d»in position «c», hold the belt to the maximum of the interval indicated.
Tighten the tensioner roller fixing nut to 2,1 ± 0,2 m.daN.
Rotate the crankshaft four turns
(normal direction of rotation).
IMPERATIVE: Never turn it backwards.
Check the timing setting by refitting the pegs [1], [2] and [3].
Remove the pegs [1], [2]and [3].
Adjusting the fitting tension of the timing belt.
Slacken the nut, holding the position of the tensioner roller, using an allen spanner at «e».
Bring the index «d»to its adjustment position at «b».
WARNING: The index «d» should not go past the notch «b». If it does, repeat the operation
to tension the timing belt.
Maintain the roller (10)in this position, using an allen spanner.
Tighten the tensioner roller fixing nut to 2,1 ± 0,2 m.daN.
IMPERATIVE: The tensioner roller should not turn during the tightening of its fixing. If it
does, repeat the operation to tension the timing belt.
Complete the refitting.
B1EP1DTC
B1EP1DUC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 192

Downloaded from www.Manualslib.com manuals search engine 195
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Setting the valve timing.
Turn the two pulleys (1)clockwise to the end of the slots.
With the belt strip (e)fully tensioned, place the belt over the pulley, first exhaust side, then inlet side, while
ensuring that marks (b)and (c)on the belt are aligned with marks (f)on the pulleys.
Hold the belt in this position and engage it over the water pump pinion and the tensioner roller.
Fit the tool [1] on the belt at (e).
Rotate the roller (2)
(using tool [5])in an anti-clockwise direction, to obtain: 63 SEEMunits.
Tighten the roller (2)to 2 m.daN.
Tighten the six screws (5)to 1 m.daN.
Essential: Check that:
- The camshaft pulleys (1)are not at the end of the slots
(by removing a screw).
- The markings on the belt are aligned with the markings on the crankshaft and camshaft pulleys.
If not, repeat the setting procedure.
B1EP11GC
B1EP11FC
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 195

Downloaded from www.Manualslib.com manuals search engine 196
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Setting the valve timing.
Remove the tools [1], [2], [3]and [4].
Rotate the engine by four turnsin the normal direction
(do not turn backwards).
Peg the flywheel [2].
Loosen the six screws (5), while ensuring there is still a slight amount of friction with the pulley.
Peg the camshaft hubs using pegs [3]and [4].
WARNING: In certain cases, it may be necessary to slightly turn the camshaft using the hub fixing screw.
Fit the tool [1].
Loosen the tensioner roller screw (2).
Rotate the roller (2)
(using tool [5])in an anti-clockwise direction to obtain: 37 SEEMunits.
Tighten the tensioner roller screw (2)to 2 m.daN.
Tighten the six pulley screws (1)to 1 m.daN.
Remove the tools.
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 196

Downloaded from www.Manualslib.com manuals search engine 200
ENGINE
200
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Peg the flywheel, using tool [1].
Position the tools [2a]and [2b].
Slacken the tensioner roller.
Turn the dynamic tensioner roller so as to be able
to position the tool[4], with the aid of an Allen key
placed at «a».
Turn the tensioner roller towards the right to bring
it to the index «c»in position «b».
Peg the tensioner roller in this position in order to
slacken the timing belt to the maximum.
IMPERATIVE: Never make the dynamic tensioner
roller turn by a complete rotation.
Remove the timing belt (8).
Check that the rollers and the pump pulley turn
freely
(no tight spot).
B1BP2MBC
B1EP170C
B1EP18PC
B1EP18QC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 200

Downloaded from www.Manualslib.com manuals search engine 201
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Refitting.
Fit the
(new)timing belt in position, in the following order:
- Inlet camshaft pulley, exhaust camshaft pulley, guide roller, crankshaft pulley, position tool [5],
coolant pump pulley, dynamic tensioner roller.
Remove tools [1], [2a], [2b]and [4].
Overtension on the belt.
Turn the tensioner roller (7)with the aid of a hexagonal spanner at «a».
Bring the index «c»to position «d», to tension the belt to the maximum of the interval indicated.
Hold the tensioner roller, using tool [4].
Tighten the fixing nut of the tensioner roller, tightening to 1 m.daN.
Turn the crankshaft by 4 rotations
(normal direction of rotation).
IMPERATIVE: Never make the crankshaft rotate backwards.
Make sure that the timing is correctly set by refitting the pegs [1], [2a]and [2b].
Remove the pegs [1], [2a], [2b]and[4].
B1EP1DPC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 201

Downloaded from www.Manualslib.com manuals search engine 203
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: RFJ
Tools.
[1]Camshaft pinion peg: (-).0194.A
[2]Crankshaft setting peg: (-).0189.R
IMPERATIVE: Respect the safety and cleanliness requirements.
Disconnect the battery.
Raise and support the vehicle, front wheels hanging.
Remove the front RH wheel, the plastic pins holding the splash-shield, the splash-shield itself.
A:Pegging on the manualgearbox.
B:Pegging on the automaticgearbox.
Turn the engine by means of the crankshaft pinion screw, to bring it to the pegging position.
B1BP2V3D
B1BP38VC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 203