2005 CITROEN C6 wheel

Downloaded from www.Manualslib.com manuals search engine 48
ENGINE
B1BP3BSD
AUXILIARY EQUIPMENT DRIVE BELT
Engine: ES9A
Tool.
[1] 2 mmdiameter peg: (-).0188-Q1
Removing.
Remove:
- The under-engine sound-deadening.
- The front RH wheel.
- The RH splash-shield.
- The air duct (linking the air distributor heat exchanger).
Compress the dynamic tensioner roller (1)to free the pegging hole at "a".
Peg the dynamic tensioner roller at "a", using tool [1].
WARNING: Do not compress the dynamic tensioner roller completely (risk
of damage).
WARNING: Mark the direction of fitting of the auxiliary equipment drive belt
if for re-use.
Disengage the auxiliary equipment drive belt from the various pulleys, commencing
at "b"(coolant pump pulley).
Remove:
- The screws (2)and (4).
- The dynamic tensioner roller (1).
- The auxiliary equipment drive belt (3).
ESSENTIAL: Check that the tensioner and guide rollers as well as the
coolant pump can turn freely (without play, without tight spots and without
projections of grease).
Angl-C6-page022-82-2005 4/02/05 17:19 Page 48

Downloaded from www.Manualslib.com manuals search engine 49
ENGINE
B1BP3BVC
AUXILIARY EQUIPMENT DRIVE BELT
Engine: DT17BTED4
Refitting.
WARNING: If re-using the auxiliary equipment drive belt, refit it respecting its direction of
fitting.
Fit the auxiliary equipment drive belt.
ESSENTIAL: Make sure that the auxiliaries drive belt is correctly positioned in the
grooves of the various pulleys.
Refit:
- The dynamic tensioner roller (1)by engaging the belt on the roller.
- The screws (2)and (4).
Tighten:
- Screw (2) : 5 ± 0,5.
- Screw (4) : 2,3 ± 0,2.
Compress the dynamic tensioner roller.
Remove tool [1].
ESSENTIAL: Make sure that the auxiliaries drive belt is correctly positioned in the
grooves of the various pulleys.
Refit:
- The air duct(linking the air distributor heat exchanger).
- The RH splash-shield.
- The front RH wheel.
- The under-engine sound-deadening.
Angl-C6-page022-82-2005 4/02/05 17:19 Page 49

Downloaded from www.Manualslib.com manuals search engine 58
ENGINE
CHECKING THE VALVE TIMING
Engine: DT17BTED4
Tools.
[1]Set of plugs: (-).0188-T
[2]Flywheel setting peg (double flywheel): (-).0195.K Toolkit 0188-T
[3]Camshaft setting pegs: (-).0195.H Toolkit 0188-T
Checks.
IMPERATIVE: Respect the safety and cleanliness requirements specific to High pressure
Diesel injection (HDi) engines.
Remove the engine cover.
Disconnect the battery negative terminal.
Raise and support the front of the vehicle.
Remove:
- The under-engine sound-deadening.
- The front RH wheel.
- The front RH splash-shield (see corresponding operation).
Remove:
- The air duct between the air/air exchanger and the air inlet housing (4).
- The air inlet housing (4).
Uncouple, plug and move aside the pipes (2)and (3), using tools [1].
Unclip and move aside the electrical harness.
Remove the venting chamber fixing (1).
Move aside the venting chamber (1).
B1BP3BXD
Angl-C6-page022-82-2005 4/02/05 17:19 Page 58

Downloaded from www.Manualslib.com manuals search engine 61
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: DT17BTED4
Tools.
[1] Kit of plugs: (-).0188-T
[2]Flywheel setting peg (double damping flywheel): (-).0195.K Toolkit 0188-T
[3]Camshaft setting pegs: (-).0195.H Toolkit 0188-T
[4]Belt compressure spring: (-).0188.K
[5]Coolant pump pulley peg: (-).0195.C
[6]Lifting bracket: (-).0195.N
IMPERATIVE: Respect the safety and cleanliness requirements.
WARNING: Before disconnectng the battery, partially open the door windows.
Removing.
IMPERATIVE: Respect the safety and cleanliness requirements specific to High pressure Diesel injection (HDi) engines.
Remove the engine cover.
Disconnect the negative terminal of the battery.
Raise and support the front of the vehicle.
Remove:
- The under-engine sound-deadening.
- The front RH wheel.
- The front RH splash-shield (see corresponding operation).
Angl-C6-page022-82-2005 4/02/05 17:19 Page 61

Downloaded from www.Manualslib.com manuals search engine 118
CLUTCH
GEARBOX
TRANSMISSION
CHECKING THE OIL PRESSURE IN THE AM6 AUTOMATIC GEARBOX
WARNING: Clean the flexible pipe of the tool [1] each time before use; the different
automatic gearbox oils cannot be intermixed.
Fit the tool [1]on the tool [2].
Perform the following operations:
- Raise the vehicle, wheels hanging.
- Apply the parking brake.
- Start the engine.
- Check the oil pressure.
WARNING: Wait for the gearbox oil to reach a temperature between 58°C and 68°C.
Check the level of oil in the gearbox (see corresponding operation).
NOTE:Check the temperature of the oil using the diagnostic tool in parameter measures.
Gear lever position: D.
Engine speed: Idling.
Principal oil pressure: 3.7 to 4.2 bars.
B1BP3END
Angl-C6-page101-120-2005 4/02/05 17:25 Page 118

Downloaded from www.Manualslib.com manuals search engine 120
CLUTCH
GEARBOX
TRANSMISSION
TRANSMISSION
Tightening torques (m.daN)Gearbox oil seal mandrels
Vehicle GearboxDriveshaft Driveshaft
Engines
bearing nutRight Left Tool kit
(-).0336.U (-).0336.V
C6 AM6 ES9A - DT17BTED4 2 ± 0,2 34,5 ± 2 8010-T
(-).0336.W (1)
(1) Guide for fitting driveshaft seal.
Tightening torques (m.daN) of the wheel bolts
CITROËNES9Al Steel
DT17BTED4 Alloy9 ± 1
Angl-C6-page101-120-2005 4/02/05 17:25 Page 120

Downloaded from www.Manualslib.com manuals search engine 121
AXLES
SUSPENSION
STEERING
WHEEL AND TYRES
Engine plate
Tyre/circumference S
Type
WheelT
A
Name of rim
Normal operating pressure:
front/rear
Pressure for maximum load :
front/rear
Pressure: loaded, high speed:
front/rear
Tyre S
Spare wheel T
Normal operating pressure
Pressure for maximum load
Pressure: loaded, high speed 3.0i 24S 2,7 24V
XFV UHZ
225/55 R17 97W/2,071 m 245/45 R18 100W/2,065m 245/45 R18 100W/2,065m
Michelin PRIMACY
7 J17-CH5-32 8 J18-CH5-33 8 J18-CH5-33
SATURNE SAN MARIN 2 SAN MARIN 2
2,4/2,4 2,4/2,4 2,4/2,4
2,6/2,6 2,4/2,4 2,6/2,6
2,4/2,4 2,4/2,4 2,6/2,6
225/55 R17 97W
7 J17-5-32
2,6 2,4 2,6
2,6 2,4 2,6S =Standard fitting.T =Steel wheel.A=Alloy wheel.
NOTE:The label indicating the recommended tyre pressures is affixed to the front LH door pillar.
Angl-C6-page121-169-2005 4/02/05 17:31 Page 121

Downloaded from www.Manualslib.com manuals search engine 122
AXLES
SUSPENSION
STEERING
WHEEL AND TYRESNOTE:The label indicating the recommended tyre pressures is affixed to the front
LH door pillar.
«a»Recommended tyre inflation pressures (empty and under load)
«b»Tyre specifications
«c»Type of tyres
«d»Recommended inflation pressure for the spare wheel
B2GP01FD
Identification of inflation pressures
Angl-C6-page121-169-2005 4/02/05 17:31 Page 122