2005 Citroen C4 warning

Downloaded from www.Manualslib.com manuals search engine 399
BRAKES
23,8 (in click) (1)
25,4/ BOSCH/MCT8 (2)
BOSCH/ZOH 54/26TEVES/F
BOSCH/ZOH 54/26TEVES/F
N3 57/26 N3 57/26
283 302 283 302
26/24
GALFER/G4554 JURID 976 GALFER/G4554 JURID 976
BOSCH/TRW C38
249
9/7
GALFER/G4554
BRAKE SPECIFICATIONS
Master cylinder
ØAmplifier
mm
Supplier
FTpistons
Disc Ventilated
Disc thickness
Brake pad grade
ØCylinder or caliper
RR mm Disc Plain
Disc thickness
Brake pad gradeWith ESP
ET3J4 TU5JP4 EW10A/J4 EW10J4S DV6TED4/ATED4DW10
BTED4
Manual/Automatic
(1) AFU system (EBA) =Emergency Brake Assist (incorporated as standard).(2) AFD system =Automatic lighting of hazard warning lamps on emergency braking (incorporated as standard).Brake fluid reservoir.Supplier: BOSCH, brake fluid quality: DOT 4.The brake fluid reservoir is in 2 parts: the principal reservoir (equipped with a level detector)and a
separate reservoir, they are linked by a rislan pipe by means of a clickfit union.
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 399

Downloaded from www.Manualslib.com manuals search engine B3FP7E1D
BRAKE SPECIFICATIONS
Braking system.
Braking circuit in the form of an X.
Disc brakes at the front and at the rear
(vehicles all types):
- The front brake discs are ventilated.
- The rear brake discs are plain.
NOTE: The front brake pads have no wear warning
lamp.
Handbrake lever controlled by cables acting on the
rear wheels.
The compensator and main brake limiter functions
are assured by the ABS REF systems.
NOTE:REF = Electronic Brakeforce Distribution (EBD).
400
BRAKESC4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 400

Downloaded from www.Manualslib.com manuals search engine 405
BRAKES
PARKING BRAKE ADJUSTMENT
Adjustment.
IMPERATIVE: Respect the safety and cleanliness requirements.
Raise and support the vehicle.
Remove the central console.
WARNING: Check the routing of the brake cables under the vehicle.
Release the handbrake lever.
Press gently on the brake pedal
(then repeat the operation 3 times).
Action the handbrake lever with a force of 40 daN.
Use a feeler gauge at «J»to measure the movement of the lever in relation to its stop.
NOTE:The movement should be less than 1,5 mmand more than 0,05 mm.
(1)Nut for adjusting the tension of the handbrake cables
Move the nut (1)to obtain a movement «J»less than or equal to 1,5 mm.
Action the handbrake lever 8 timeswith a force of 40 daN.
With the handbrake released, check the movement «j»with a feeler gauge.
NOTE:The movement should be less than 1,5 mmand more than 0,05 mm.
Refit the central console
(see corresponding operation).
Check the efficiency of the handbrake.
B3FP7F1C
B3FP7F2D
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 405

Downloaded from www.Manualslib.com manuals search engine 408
BRAKES
B3FP7EUC
BLEEDING AND FILLING THE BRAKING SYSTEM
Filling the braking circuit.
WARNING: Use only the approved and recommended hydraulic fluids.
IMPERATIVE: Only use new brake fluid that has not emulsified; avoid any introduction of
impurities into the hydraulic circuit.
Fill the brake fluid reservoir (4).
Bleeding the primary braking circuit.
WARNING: During the bleed operations: take care to maintain the level of the brake fluid
in the reservoir, keep it topped up.
WARNING: The ABS system must not be in action during the bleed operation.
WARNING: Respect the sequence for the opening of the bleed screws.
Front brake caliper : Bleed screw (8).
Rear brake caliper : Bleed screw (9).
Bleed each brake caliper, proceeding in the following sequence:
- Front LH wheel.
- Front RH wheel.
- Rear LH wheel.
- Rear RH wheel.
B3FP7ETC
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 408

Downloaded from www.Manualslib.com manuals search engine 410
BRAKESBLEEDING AND FILLING THE BRAKING SYSTEM
Bleeding the braking circuit without the bleed apparatus.
NOTE:Two operators are necessary.
For each brake circuit:
- Apply the brake pedal to place the circuit under pressure.
- Couple a transparent tube on the bleed screw.
- Submerge the other end of the tube in a clean container.
- Open the bleed screw.
- Wait until the fluid flows out without air bubbles.
- Close the bleed screw.
NOTE:Recommence the process a second timeif that is necessary.
Check the level of the brake fluid
(between the «DANGER»level and
the «MAXI»level).
Fill if necessary with the the approved and recommended synthetic
brake fluid.Bleeding the secondary braking circuit.
WARNING: During the bleed operations: take care to maintain the
level of the brake fluid in the reservoir, keep it topped up.
NOTE:The bleed apparatus [1]is still connected on the brake fluid
reservoir (4).
Use the diagnostic tools [2]or [3].
Select the menu corresponding to the vehicle:
- ABSmenu
(according to equipment).- ESPmenu (according to equipment).
Follow the instructions of the diagnostic tool.
At the end of the bleed programme, check the level of the brake fluid,
top up if necessary.
Check the travel of the brake pedal: it must not be excessive. If it is,
restart the bleed procedure.
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 410

Downloaded from www.Manualslib.com manuals search engine 413
BRAKES
BRAKE SPECIFICATIONS
Gyrometer sensor (7) Hydraulic block
C4AP17YCB3HP002C
Observations Part no. Supplier Components
XSARA
ESP hydraulic
blockBOSCH 5.7 ESPLocated on the front
LH wheelarch:
4 adjustmentchannels.IMPERATIVE: Respect the direction of fitting of the gyrometer/
accelerometer sensor
(connector towards the rear of the vehicle).WARNING: The gyrometer/accelerometer sensor should not be
subjected to any impact. Any gyrometer/accelerometer sensor
having suffered an impact must be replaced.
Tightening torque (15): 0,6 ± 0,1 m.daN.
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 413

Downloaded from www.Manualslib.com manuals search engine 427
BRAKES
BLEEDING THE BRAKING SYSTEMXSARA PICASSO
Tools Bleeding equipment of type «LURO» or similar.
IMPERATIVE: For bleeding the secondary circuit, use ELIT, LEXIA or PROXIA diagnostic tools.
Draining.
Drain the brake fluid reservoir as empty as possible using a syringe.
Disconnect the brake fluid warning lamp connector.
Retrieve the brake fluid reservoir from its supply pipes by pulling upwards.
Finish emptying the reservoir of brake fluid.
Clean the brake fluid reservoir.
Refit the brake fluid reservoir.
Reconnect the brake fluid warning lamp connector.
Filling.
Refill the reservoir with brake fluid.
WARNING: Use only the recommended hydraulic fluids.
Bleeding.
NOTE:Two technicians are required.
IMPERATIVE: During bleed operations, ensure that the level of brake fluid is maintained
in the reservoir and top it up, use only new brake fluid.
Bleed each wheel cylinder, proceeding in the following order:
- Rear right hand wheel.
- Front left hand wheel.
- Rear left hand wheel.
- Front right hand wheel.
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 427