2005 Citroen C4 warning

Downloaded from www.Manualslib.com manuals search engine 317
CLUTCH
GEARBOX
TRANSMISSION
HYDRAULIC CLUTCH CONTROL: CHECKS AND ADJUSTMENTS
B2BP04XC
IMPERATIVE: Use only new brake brake fluid that is not emulsified, avoid any
ingress of impurities into the hydraulic circuit.
IMPERATIVE: Do not use automatic bleeding equipment
(risk of the brake fluid
emulsifying in the hydraulic circuit).
Couple a transparent tube (5)on the bleed screw, at «c».
Submerge the end of the tube (5)in the recipient containing the brake fluid, located
below the level of the clutch slave cylinder.
Use the transparent tube (5) to act as a siphon, at «b».
WARNING: the end of the tube (5) must be submerged in the brake fluid.
Open the bleed screw at «c».
XSARA PICASSO
Bleeding the hydraulic clutch control
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 317

Downloaded from www.Manualslib.com manuals search engine 334
CLUTCH
GEARBOX
TRANSMISSION
CHECKS AND ADJUSTMENTS: MA/5 GEARBOX CONTROLS
Engines: KFW - NFU - 8HX - 8HZ
(1)Gear lever
(2)Gear control bar
(3)Engagement rod
(4)Gear selection rod
(5)Torque reaction rod
(6)Gear engagement ball-joint
(7)Fixed point on gearbox
Adjustment.
The gear control assembly is not adjustable.
The rods do not have threaded ends.
Features.
Grease the gear engagement ball-joint.
WARNING: To secure the ball-joints, set the
gearbox control to neutral. After fitting the gear
control assembly, check that all the gears will
engage without any ”tight spot”.
B2CP27WD
XSARA
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 334

Downloaded from www.Manualslib.com manuals search engine 339
CLUTCH
GEARBOX
TRANSMISSION
CHECKS AND ADJUSTMENTS: BE4/5 GEARBOX CONTROLS
Principles of adjusting the gear controls.
WARNING: Cables should be adjusted each time the gearbox, gear controls or power unit are
removed.
Principles.
Lock the gear lever in neutral position, using tool: 9607-T.
Place the gearbox in neutral.
Couple the cables on the lever.
Fit the ball-joints on the gearbox lever.
Lock the cable lengths with the ball-joint locking keys.
WARNING: Do not use any tool to unclip the ball-joints.
To unlock the ball-joint, press at the centre «a», then pull the ball-joint upwards.
NOTE:Changing an individual ball-joint is possible as long as the locking key is removed.
Unclip at «b», using two small screwdrivers.
Engines: NFV - 6FZ - RFN - WJY - 8HX - 8HZ - 9HY - 9HZ - RHY - RHZ
XSARA - XSARA PICASSO
B2CP3BXC
B2CP3BYC
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 339

Downloaded from www.Manualslib.com manuals search engine 340
CLUTCH
GEARBOX
TRANSMISSION
CHECKS AND ADJUSTMENTS: BE4/5 GEARBOX CONTROLS
Tools.
[1]Tool for positioning the gear lever: 9607-T
Adjustments.
WARNING: Cables should be adjusted each time
the gearbox, gear controls or power unit are
removed.
Inside the vehicle.
Remove the trim under the gear lever.
Lock the gear lever in neutral position, using tool [1].
Under the bonnet.
Remove the air filter assembly.
Unlock the ball-joint keys at «a».
Place the gear selection and control levers on neutral.
Lock the cable lengths with the ball-joint locking keys.Checks.
Remove the tool [1].
Check that all the gears engage without «tightness».
Check that the gear lever moves identically forwards
and backwards and to right and left.
If it does not, repeat the adjustment.
Refit the trim under the gear lever.
Refit the air filter assembly.
Adjusting the gear controls Engines: NFV - 6FZ - RFN - WJY - 8HX - 8HZ - 9HZ - 9HY - RHY - RHZ
XSARA - XSARA PICASSO
B2CP3C6CB2CP3C0C
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 340

Downloaded from www.Manualslib.com manuals search engine 345
CLUTCH
GEARBOX
TRANSMISSION
RECOMMENDATIONS/PRECAUTIONS : AL4 AUTOMATIC GEARBOX
Procedure to be followed prior to carrying out repairs on AL4 autoactive gearbox
If a gearbox malfunction occurs, there are two possible configurations
depending on the seriousness of the fault:
- Gearbox in back-up mode with a replacement programme of
(the fault
values are taken in substitution).
- Gearbox in back-up mode with an emergency programme (3rd hydraulic).
WARNING: In the emergency programme, an impact is felt when
changing P/R, N/R and N/D.
Réception client.
Discuss with the customer, to find out all the malfunction symptoms.
Oil quality - Oil level.
Oil quality.
If the gearbox has suffered a serious fault resulting in a malfunction or
the destruction of a clutch, the oil will overheat and become
contaminated with impurities: the oil is said to be «burnt».
This is characterised by a black colour and the presence of an
unpleasant smell.
ESSENTIAL: The gearbox must be replaced.Oil level
(see corresponding operation).
An excessive oil level can result in the following consequences:
- Excessive heating of the oil.
- Oil leaks.
An insufficent level causes the destruction of the gearbox.
Top up the level of oil in the gearbox
(if necessary).
Check using a diagnostic tool.
Read the fault codes
(engine and gearbox).
Absence of fault codes.
Carry out parameter measures, actuator tests and a road test.
Presence of fault codes.
Carry out the necessary repairs.
Delete the fault codes.
Carry out a road test to check the repair and, if need be, modify the
gearbox ECU parameters
(this is essential after an initialisation of the
ECU).
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 345

Downloaded from www.Manualslib.com manuals search engine 359
CLUTCH
GEARBOX
TRANSMISSION
AL4 GEARBOX CONTROLS
Refitting.
Proceed in the opposite order to removal.
Lubricate the support (13).
New gear selection control.
Couple the ball-joint (6).
WARNING: Do not deform the selection lever on the automatic gearbox.
Push in the component (a)without bending the cable.
Check all the gear selection control positions.
Re-used gear selection control.
Release the component (a).
Couple the ball-joint (6).
Push in the component (a)without bending the cable.
Check all the gear selection control positions.
Engine: RFN
XSARA PICASSO
B2CP3NFD
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 359

Downloaded from www.Manualslib.com manuals search engine 388
AXLES
SUSPENSION
STEERING
H1 = R1 – L1 H1’ = R1 – L1’
H1 = From the front suspension arm linkage bolt axis to the ground.
R1 =Radius of the front wheel when laden.
L1 =From the centre of the wheel to the front suspension arm linkage
bolt axis.
H1' =From the front jacking point to the ground.
L1' =From the front jacking point to the radius of the front wheel when
laden.H2 = R2 - L2
H2 = From the rear axle silentblock face to the ground.
R2 =Radius of the rear wheel when laden.
L2 =From the centre of the wheel to the rear axle silentblock face.
AXLE GEOMETRY
Measurements at reference height
NOTE: To make the setting of reference height easier, it is acceptable to take the measurement from the flange of the jacking point.
WARNING: The values shown should only be used as guides. In case of doubt, check the settings at reference height
Rear heightFront height
B3CP05BCB3CP058DB3DP079C
XSARA PICASSO
Conditions for checking and adjusting: Tyres inflated to correct pressures. Vehicle at reference height. Steering rack locked at mid point(see corresponding operation).
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 388

Downloaded from www.Manualslib.com manuals search engine 398
BRAKES
22,2 (in valve) (1)
22,86/BOSCH/EVA2 (2)25,4/ BOSCH/MCT8 (2)
BOSCH/ZOH 54/22 BOSCH/ZOH 54/26
266 283
22/20 26/24
FEDERAL MODUL/F769 GALFER/G4554
BOSCH/TRW C38
249
9/7
GALFER/G4554
BRAKE SPECIFICATIONS
Master cylinder
ØAmplifier
FT mm Supplier/pistons
Disc Ventilated
Disc thickness
Brake pad grade
ØCylinder or caliper
RR mm Disc Plain
Disc thickness
Brake pad gradeWith ABS
ET3J4 TU5JP4 DV6 TU5JP4
Manual Auto.
(1) AFU system (EBA) =Emergency Brake Assist (incorporated as standard).(2) AFD system =Automatic lighting of hazard warning lamps on emergency braking (incorporated as standard).Brake fluid reservoir.Supplier: BOSCH, brake fluid quality: DOT 4.
The brake fluid reservoir is in 2 parts: the principal reservoir (equipped with a level detector)and a separate reservoir, they are linked by a rislan
pipe by means of a clickfit union.
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 398