2005 Citroen C4 M.dan

Downloaded from www.Manualslib.com manuals search engine 393
AXLES
SUSPENSION
STEERING
TIGHTENING TORQUES: FRONT AXLE
Tightening torques (m.daN).(1) Damper nut: 4.5 ± 0.4
(2)Cup screw: 2.5 ± 0.2
(3)Suspension leg
(4)Anti-roll bar link rod ball-joint: 3.7 ± 0.3
(5)Suspension leg swivel: 4.5 ± 0.4
(6)Anti-roll bar
(7)Anti-roll bar link rod ball-joint: 3.7 ± 0.3
(8)Lower swivel ball-joint: 4 ± 0.4
(9)Hub nut
(greased): 32.5 ± 2
(10)Wheel bolt
(face and threads not greased): 9 ± 1
(11) Lower arm front pivot: 7.6 ± 0.7
(12) Lower arm rear pivot and
anti-roll bar bearing: 6.8 ± 0.6
(13) Screw under rear pivot : 3.5 ± 0.3
Lower arm in forged steel : 3.7 ± 0,3
Lower arm in plate steel: 3.1 ± 0,3
Screw fixing subframe on bodyshell: 8.5 ± 0,8
Screw fixing ball-joint on lower
arm
(plate steel): 4.5 ± 0,4
Anti-roll bar
Engines
ALL TYPESDiameter
21Colour ref.
WHITE Suspension leg angle:
Ta b«a»towards the front.
B3CP056P
B3CP057D
B3CP043D
XSARA PICASSO
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 393

Downloaded from www.Manualslib.com manuals search engine 394
AXLES
SUSPENSION
STEERING
TIGHTENING TORQUES: REAR AXLE
Tightening torques (m.daN).
(14)Front silentblock on subframe: 9.4 ± 0.9
(15)Anti-roll bar bolt: 5.5 ± 0.5
(16)Rear torsion bar
(17) Anti-roll bar
(18) Tubular axle
(19)Front silentblock on bodyshell: 4 ± 0.4
(20)Rear upper arm.
(21)Wheel bolt
(face and threads not lubricated): 9 ± 1
(22)Damper
(23)Rear silentblock on subframe: 5.4 ± 0.5
(24)Damper pin nut: 11 ± 1
(25)Stub axle nuts
(lubricated): 25 ± 2
(26)Rear silentblock on bodyshell: 6.5 ± 0.6
Anti-roll bar
Torsion bar
Engines
ALL TYPES 19,6 PINKØ (mm)
Colour ref.Ø (mm)
21Colour ref.
ORANGE
B3DP078D
NOTE: The RH torsion bar can be identified by 1 paint line.
The LH torsion bar can be identified by 2 paint lines.
XSARA PICASSO
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 394

Downloaded from www.Manualslib.com manuals search engine 395
AXLES
SUSPENSION
STEERING
TIGHTENING TORQUES: POWER-ASSISTED STEERING
Tightening torques (m.daN).
(2) Airbag to steering wheel fixing: 0.8 ± 0.1
(3)Steering wheel fixing: 3.3 ± 0.6
(5)Steering column to support fixing: 4 ± 0.1
(6)Steering cardan joint fixing: 2.3 ± 0.2
B3EP116D
XSARA PICASSO
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 395

Downloaded from www.Manualslib.com manuals search engine 396
AXLES
SUSPENSION
STEERING
TIGHTENING TORQUES: POWER-ASSISTED STEERING
Tightening torques (m.daN).
(7) Pivot ball-joint nut: 4 ± 0.4
(8) Steering rod adjusting lock nut: 4.5 ± 0.4
(9)Ball-joint on steering rack: 6 ± 0.6
(10) Fixing steering on subframe: 8 ± 0.8
(11)Hydraulic pipe connection: 2.4 ± 0.2
(12)Power steering valve: 1.2 ± 0.2
(13)Plunger flange screws: 1.2 ± 0.2
(14)Steering ram screw on housing: 9 ± 1
(15) Steering ram screw on yoke: 9 ± 1
NOTE:When removing the steering, it is imperative to replace screws
(14)and (15)
(new screws).
B3EP117D
XSARA PICASSO
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 396

Downloaded from www.Manualslib.com manuals search engine 397
AXLES
SUSPENSION
STEERING
TIGHTENING TORQUES: POWER-ASSISTED STEERING
Tightening torques (m.daN).
Unions between pump unions and power steering valve: 2 ± 0.3
(16)Fixing screw: 2.2 ± 0.3
(17)Fixing screw: 2.2 ± 0.3
(18) Fixing screw: 2.2 ± 0.3
NOTE: Coat the threads with product «E3».
A pressure switch is implanted in the hydraulic piping between the high
pressure pump and the power steering valve.
- Opening pressure = 30 / 35 bars.
- Closing pressure = 25 barsminimum.
Tightening torque = 2 ± 0.2.
B3EP118D
XSARA PICASSO
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 397

Downloaded from www.Manualslib.com manuals search engine 413
BRAKES
BRAKE SPECIFICATIONS
Gyrometer sensor (7) Hydraulic block
C4AP17YCB3HP002C
Observations Part no. Supplier Components
XSARA
ESP hydraulic
blockBOSCH 5.7 ESPLocated on the front
LH wheelarch:
4 adjustmentchannels.IMPERATIVE: Respect the direction of fitting of the gyrometer/
accelerometer sensor
(connector towards the rear of the vehicle).WARNING: The gyrometer/accelerometer sensor should not be
subjected to any impact. Any gyrometer/accelerometer sensor
having suffered an impact must be replaced.
Tightening torque (15): 0,6 ± 0,1 m.daN.
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 413

Downloaded from www.Manualslib.com manuals search engine 414
BRAKES
TIGHTENING TORQUES: BRAKING SYSTEM
XSARA
Tighten the nuts (1)to 2.3 m.daN.
The shaft (2)is held in place by a plastic clip.
B3FP10YD
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 414

Downloaded from www.Manualslib.com manuals search engine 436
AIR
CONDITIONING
SPECIAL FEATURES: AIR CONDITIONING SYSTEM (R 134.a)
Changing the filtering/drying cartridge
Move aside the radiator/condenser assembly.
Remove the plug (6), using tool [2].
Support the radiator/condenser assembly thus moved aside.
Remove the filtering/drying cartridge (7), using pliers.
Refitting.
Refit the filtering/drying cartridge (7).
Clean the threads of the plug (6).
It is essntial to change the O-ring seals (8).
Lubricate the O-ring seals (8)with aircon compressor oil.
Refit:
- The plug (6), using tool [2], tighten to 1,4 ± 0,2 m.daN.
- The brackets (5).
- The screws (4).
- The cardboard from the radiator harness.
- The nuts (1).
- The air filter assembly (3).
Couple the hose (2).
Recharge the circuit (R134.a)
(according to equipment) (see corresponding
operation).
Check the operation of the air conditioning.
C5HP14NCC5HP14PCC5HP14QC
XSARA PICASSO
Angl.-t2-page428-456-2005 9/01/06 10:25 Page 436