2005 Citroen BERLINGO Alternator

Downloaded from www.Manualslib.com manuals search engine 110
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Accessories
49 Multifunction support 2 ± 0,4
50 Alternator fixing screw 4,9 ± 1,2
51 Alternator power circuit fixing nut 1,4 ± 0,2
52 Accessories tensioner roller 2,1 ± 0,2
Engine: 9HX
D1AP02NC
Version without particle filter
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 110

Downloaded from www.Manualslib.com manuals search engine 122 122
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Accessories
49 Multifunction support 2 ± 0,4
50 Alternator fixing screw 4,9 ± 1,2
51 Alternator power circuit fixing nuts 1,4 ± 0,2
52 Accessories tensioner roller 2,1 ± 0,2
Engines: 9HY - 9HZ
D1AP02NC
Version without particle filter
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 122

Downloaded from www.Manualslib.com manuals search engine 147
ENGINE
SPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Accessories
34 Alternator support 2 ± 0,2
35 Alternator 4,9 ± 0,4
36 Aircon compressor 2,5 ± 0,2
37 Accessories belt tensioner roller 4,3 ± 0,4
Engine: RHR
B1BP390D
C4
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 147

Downloaded from www.Manualslib.com manuals search engine 155
ENGINE
[1] Belt tension measuring instrument
: 4122-T
- Tension the belt using the screw (2).
- Tension should be:
102 ± 7 SEEM units.
- Tighten the screws(1).
- New belt
100 SEEM units.
- Re-used belt
75 SEEM units.
AUXILIARY EQUIPMENT DRIVE BELT
Alternator
Power-assisted steering Power steering and air con.With air conditioning
[1] Belt tension measuring instrument
: 4122-T
- Tension the belt using the screw (4).
- Tension should be:
102 ± 7 SEEM units.
- Tighten the screws (3).
- New belt
100 SEEM units.
- Re-used belt
75 SEEM units.
B1BP1B3CB1BP124CB1BP1B2CB1BP122C
Engine: KFW
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 155

Downloaded from www.Manualslib.com manuals search engine 156
ENGINE
B1BP2LSC
B1BP2LTC
AUXILIARY EQUIPMENT DRIVE BELT
Engines: KFU - NFU
Tools.
[1]Pliers for removing plastic pegs: 7504 -T
[2]Belt tension measuring instrument (SEEM) : 4122 -T
[3]Compression lever for dynamic tensioner: (-).0194.D
[4] Peg for dynamic tensioner roller of Ø 4 mm : (-) 0194.F
WARNING: (With or without air conditioning)
The auxiliaries drive belt cannot be re-used
with a manual tensioner roller.
The auxiliaries drive belt can be re-usedwith a dynamic tensioner roller.
Removing.
Raise and support the vehicle, front wheels hanging.
Disconnect the battery.
Remove the front RH wheel and the front RH splash-shield, using tool [1].
V
ehicle without air conditioning.Slacken bolts (2), screw (3)and the tensioning screw (1).
Push back the alternator towards the engine.
Remove the auxiliary equipment drive belt.
Refitting.
Refit the new auxiliary equipment drive belt.
Respect the following sequence: Crankshaft pinion, alternator pulley.
Position tool [2]on the belt.
Tighten the screw (1)to tension the belt to: 120 ± 4 SEEM units.
Tighten screw (3), bolts (2).
Remove tool [2].
Complete the refitting.
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 156

Downloaded from www.Manualslib.com manuals search engine 157
ENGINE
B1EP1GQD
AUXILIARY EQUIPMENT DRIVE BELT
Engine: KFU
Véhicule with air conditioning.
Removing.
Place tool [4]at «a».
Compress the dynamic tensioner roller.
Place tool [3]at «b».
Remove the auxiliary equipment drive belt.
IMPERATIVE: Check that the dynamic tensioner roller turns freely
(without play and without tight
spots).
Refitting.
NOTE: Visually check the condition of the auxiliary equipment drive belt prior to refitting.
Place tool [4]at «a».
Compress the dynamic tensioner roller.
Remove tool [3].
Refit the auxiliary equipment drive belt.
Respect the following sequence:
- Crankshaft pinion, aircon compressor pulley, alternator pulley, dynamic tensioner roller.
Remove the tools.
Complete the refitting.
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 157

Downloaded from www.Manualslib.com manuals search engine 161
ENGINE
B1EP1FUD
B1EP1FVC
AUXILIARY EQUIPMENT DRIVE BELT
Engine: RFJ
Tool.
[1]«Junior» T extension: (-).1608.E
Removing.
Engage tool [1]in the notch «a».
Exert on the roller (1)an effort upwards to hold it at maximum.
Remove the auxiliaries drive belt.
Carefully release the tensioner roller (1)to reach its minimum.
Remove tool[1].
IMPERATIVE: Check that the roller (1) turns freely
(without play and without tight spots).
Refitting.
If removing the auxiliaries drive belt tensioner roller, tighten the screws 2 ± 0,2 m.daN.
Engage tool [1]in the notch at «a».
Exert on the roller (1)an effort upwards to hold it at maximum.
Position the
(new)auxiliaries drive belt, in the following sequence:
- Auxiliaries drive pulley (4), aircon compressor pulley (3), tensioner roller (1)and alternator pulley (2).
IMPERATIVE: Make sure that the auxiliaries drive belt is correctly positioned in the grooves of
the various pulleys.
Release the tensioner roller (1).
Remove tool [1].
Checking the tension of the auxiliaries drive belt.
Check the tension of the auxiliaries drive belt:
- Mark «b»at the level of mark «c», new belt.
- Mark «b»at the level of mark «d», belt to be changed.
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 161

Downloaded from www.Manualslib.com manuals search engine 172
ENGINEXSARA
AUXILIARY EQUIPMENT DRIVE BELT
Power-assisted steering, without air conditioning
Tool.
[1] Belt tension measuring instrument: 4122-T
Removal.
WARNING: If the belt is to be reused, measure the tension before removal.
Loosen:
- the screw (1).
- the nut (2).
NOTE:The tensioner arm (3)must be against the alternator.
Remove the belt.
B1BP1SHD
Engine: WJY
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 172