2005 CHRYSLER CARAVAN fold seats

SYMPTOM POSSIBLE CAUSE
Sunshade will not function or does not
operate smoothlySunshade feet are missing, broken or loose.
No lubracation in track.
Track obstructions or interference.
Glass movement not consistant or glass does
not operate smoothlyGlass and Track timing.
Glass and Track alignment
Cables and Guide alignment
WATER DRAINAGE AND WIND NOISE DIAGNOSIS
The sliding glass panel is designed to seal water
entry with a snug fit between the roof and the seal.
The fit can be checked by inserting a piece of paper
between the roof and the seal. The piece of paper
should have some resistance when pulled out when
the glass panel is in the closed position. Excessive
wind noise could result if the gap clearances are
exceeded. The sunroof glass panel may need to be
adjusted. Refer to Sunroof Glass Panel Adjustment
for proper procedures.
Adequate drainage is provided by a drain trough in
the sunroof housing which encircles the sliding glass
panel and leads to drain hoses. If a wet headliner or
other water leak complaints are encountered, before
performing any adjustments, first ensure that the
drainage system is not plugged or disconnected. Use
a pint container to pour water into the sunroof hous-
ing drain trough. If water flow is restricted in any of
the four drain holes, use compressed air to blow out
any material plugging the drain system. Retest sys-
tem again.
To further check for a disconnected drain hose:
(1) Remove A-pillar trim, sun visors, and map
lamps/mini console.
(2) Remove sunroof opening trim lace. Refer to
Sunroof Opening Trim Lace.
NOTE: Care must be taken not to fold or kink the
headliner upon removal.
(3) Lower headliner as necessary to gain access to
sunroof housing drain tubes. Refer to Headlining
Removal and Installation for proper procedures.
(4) Repair as necessary.
DRAIN TUBE
REMOVAL
FRONT HOSES
NOTE: Front A-pillars are filled with sound deaden-
ing foam and the front drain tubes are sealed into
the pillars.
(1) Move glass panel to the fully closed position.
(2) Disconnect negative battery cable.
(3) Remove headliner (Refer to 23 - BODY/INTE-
RIOR/HEADLINER - REMOVAL).
(4) Disconnect the drain hose from the sunroof
housing (Fig. 1).
(5) Drain any liquid from hose connection, repair
as necessary.
REAR HOUSING HOSE
(1) Move glass panel to the fully closed position.
(2) Disconnect negative battery cable.
(3) Remove headliner (Refer to 23 - BODY/INTE-
RIOR/HEADLINER - REMOVAL).
(4) Remove third seat or seats from vehicle.
(5) Remove second seat belt lower anchor.
(6) Remove third seat lower anchor.
(7) Remove quarter trim bolster.
(8) Remove trim panel screws.
(9) Remove quarter trim panel
(10) Disconnect the drain hose from the sunroof
housing. (Fig. 1).
(11) Drain any liquid from hose connection, if nec-
essary, and remove tube.
INSTALLATION
FRONT HOSES
(1) Connect the new drain hose to the sunroof
housing and test drainage (Fig. 1).
(2) Install headliner (Refer to 23 - BODY/INTERI-
OR/HEADLINER - INSTALLATION).
(3) Install sunroof opening trim lace.
(4) Connect the control switch wire connector and
install control switch.
23 - 172 SUNROOFRS
SUNROOF (Continued)

DISTRIBUTION - REAR
TABLE OF CONTENTS
page page
AIR OUTLETS
DESCRIPTION.........................56
REMOVAL.............................56
INSTALLATION.........................56
DISTRIBUTION DUCT
REMOVAL.............................57
INSTALLATION.........................57
BLOWER MOTOR
DESCRIPTION.........................57
OPERATION...........................57DIAGNOSIS AND TESTING
REAR BLOWER MOTOR................58
REMOVAL.............................58
INSTALLATION.........................60
HVAC HOUSING
REMOVAL.............................60
INSTALLATION.........................62
REAR FLOOR HEAT DUCT
REMOVAL.............................63
INSTALLATION.........................63
AIR OUTLETS
DESCRIPTION
Based upon the system mode selected, conditioned
air can exit the rear HVAC housing through one or a
combination of the two main housing outlets: air con-
ditioner, or heater. Once the conditioned air exits the
unit housing, it is directed through molded plastic
ducts to the various outlets in the vehicle interior.
These outlets and their locations are as follows:
²Floor Outlets- Three floor outlets with fixed
vanes are located in the right quarter trim panel,
near the floor. These outlets distribute air from the
rear floor heat duct to the intermediate and rear seat
occupants. The floor outlets are integral to the right
quarter trim panel and, if faulty or damaged, the
quarter trim panel must be replaced.
²Overhead Outlets- Four (two right side and
two left side) fully adjustable outlets along the roof
rails distribute air from the rear distribution duct
and the headliner ducts to the intermediate and rear
seat occupants. The headliner ducts are integral to
the headliner panel. Each overhead outlet is housed
in a headliner bezel. The two forward headliner
bezels also feature a courtesy lamp, a fold-away coat
hook, and a fold-away assist handle. The overhead
outlets can be removed from the headliner bezels
individually for service replacement.
REMOVAL
(1) Using a trim stick or another suitable wide
flat-bladed tool, gently pry the thumb wheel end of
the overhead outlet away from the pivot pin in the
headliner bezel until one end of the outlet is released
(Fig. 1).(2) Pull the opposite end of the overhead outlet
away from its pivot pin in the headliner bezel until
that end of the outlet is released.
(3) Remove the overhead outlet from the opening
in the headliner bezel.
INSTALLATION
(1) Position the overhead outlet into the opening in
the headliner bezel.
(2) Slide the non-thumb wheel end of the outlet
onto the pivot pin in the headliner bezel. Using hand
pressure, push the thumb wheel end outboard onto
the pivot pin until it fully seats.
Fig. 1 Overhead Outlet
1 - HEADLINER BEZEL
2 - OVERHEAD OUTLET
3 - TRIM STICK
4 - COURTESY LAMP
5 - COAT HOOK
6 - ASSIST HANDLE
24 - 56 DISTRIBUTION - REARRS

(4) Open both the suction and discharge valves,
then open the charge valve to allow the heated
refrigerant to flow into the system.
(5) When the transfer of refrigerant has stopped,
close both the suction and discharge valves.
(6) If all of the refrigerant charge did not transfer
from the dispensing device, open all of the windows
in the vehicle and set the heater-air conditioner con-
trols so that the compressor is engaged and the
blower motor is operating at its lowest speed setting.
Run the engine at a steady high idle (about 1400
rpm). If the compressor will not engage, test the com-
pressor clutch control circuit and repair as required.
(7) Open the suction valve to allow the remaining
refrigerant to transfer to the refrigerant system.
WARNING: TAKE CARE NOT TO OPEN THE DIS-
CHARGE (HIGH PRESSURE) VALVE AT THIS TIME.
(8) Close the suction valve and test the system
performance. (Refer to 24 - HEATING & AIR CON-
DITIONING - STANDARD PROCEDURE - A/C PER-
FORMANCE TEST).
(9) Disconnect the charging station and manifold
gauge set from the refrigerant system service ports.
(10) Reinstall the caps onto the refrigerant system
service ports.
(11) Run the HVAC Control Cooldown test to ver-
ify proper operation(Refer to 24 - HEATING & AIR
CONDITIONING - DIAGNOSIS AND TESTING).
A/C COMPRESSOR
DESCRIPTION
A/C COMPRESSOR
Vehicles equipped with the 2.4L gasoline, 2.5L die-
sel, 2.8L diesel and 3.3L gasoline engines with the
front heating-A/C system only, use the Denso 10S17
A/C compressor. Vehicles equipped with the 3.3L and
the 3.8L gasoline engines with the optional rear heat-
ing-A/C system use the Denso 10S20 A/C compressor.
Both A/C compressors include an integral high pres-
sure relief valve. The A/C compressor is secured to a
mounting bracket on the 2.4L gasoline engine and
directly to the cylinder block on the 2.5L diesel, 2.8L
diesel, 3.3L gasoline and 3.8L gasoline engines.
HIGH PRESSURE RELIEF VALVE
A high pressure relief valve is located on the rear
of the A/C compressor. This mechanical valve is
designed to vent refrigerant from the A/C system to
protect against damage to the compressor and other
system components, caused by condenser air flow
restriction or an overcharge of refrigerant.
OPERATION
A/C COMPRESSOR
The A/C compressor is driven by the engine
through an electric clutch, drive pulley and belt
arrangement. The compressor is lubricated by refrig-
erant oil that is circulated throughout the refrigerant
system with the refrigerant.
The compressor draws in low-pressure refrigerant
vapor from the evaporator through its suction port. It
then compresses the refrigerant into a high-pressure,
high-temperature refrigerant vapor. The compressor
pumps the high-pressure refrigerant vapor to the
condenser through the compressor discharge port.
The compressor cannot be repaired. If faulty or
damaged, the entire compressor assembly must be
replaced. The compressor clutch, pulley and clutch
coil are available for service.
HIGH PRESSURE RELIEF VALVE
The high pressure relief valve vents the system
when a discharge pressure of 3445 to 4135 kPa (500
to 600 psi) or above is reached. The valve closes
when a minimum discharge pressure of 2756 kPa
(400 psi) is reached.
The high pressure relief valve vents only enough
refrigerant to reduce the system pressure, and then
re-seats itself. The majority of the refrigerant is con-
served in the system. If the valve vents refrigerant, it
does not mean that the valve is faulty.
The high pressure relief valve is a factory-cali-
brated unit. The valve cannot be adjusted or
repaired, and must not be removed or otherwise dis-
turbed. The valve is only serviced as a part of the
compressor assembly.
DIAGNOSIS AND TESTING
A/C COMPRESSOR NOISE DIAGNOSIS
Excessive noise while the air conditioning compres-
sor is operating can be caused by loose compressor
mounts, a loose compressor clutch, or high operating
pressures in the refrigerant system. Verify compres-
sor drive belt condition, proper compressor mounting,
correct refrigerant charge level, and compressor head
pressure before compressor repair is performed.
With the close tolerances within the compressor, it
is possible to experience a temporary lockup. The
longer the compressor is inactive, the more likely the
condition is to occur. This condition is the result of
normal refrigerant migration within the refrigerant
system caused by ambient temperature changes. The
refrigerant migration may wash the refrigerant oil
out of the compressor.
24 - 72 PLUMBING - FRONTRS
PLUMBING - FRONT (Continued)

DEFOGGER RELAY - DESCRIPTION,REAR WINDOW ....................... 8G-3
DEFOGGER RELAY - INSTALLATION, REAR WINDOW ....................... 8G-4
DEFOGGER RELAY - OPERATION, REAR WINDOW ............................ 8G-3
DEFOGGER RELAY - REMOVAL, REAR WINDOW ............................ 8G-4
DEFOGGER SWITCH - DESCRIPTION, REAR WINDOW ....................... 8G-4
DEFOGGER SWITCH - OPERATION, REAR WINDOW ............................ 8G-4
DEFROSTER DUCT - INSTALLATION ......24-50
DEFROSTER DUCT - REMOVAL ..........24-49
DEMAGNETIZING, STANDARD PROCEDURE - COMPASS ...............8M-5
DEMISTER DUCTS - INSTALLATION, INSTRUMENT PANEL .................. 24-54
DEMISTER DUCTS - REMOVAL, INSTRUMENT PANEL .................. 24-54
DEMISTER OUTLETS, INSTALLATION - FRONT ............................. 24-45
DEMISTER OUTLETS, REMOVAL - FRONT . 24-44
DEPLOYMENT - STANDARD PROCEDURE, SERVICE AFTER AN
AIRBAG ............................. 8O-7
DETECTION ASSY - INSTALLATION, NATURAL VAC LEAK .................. 25-14
DETECTION ASSY - REMOVAL, NATURAL VAC LEAK .......................... 25-14
DETECTION PUMP - INSTALLATION, LEAK .............................. 25-15
DETECTION PUMP - REMOVAL, LEAK ......25-15
DEVICES - STANDARD PROCEDURE, ELECTROSTATIC DISCHARGE (ESD)
SENSITIVE ........................8W -01-8
DIAGNOSTIC SYSTEM, DIAGNOSIS AND TESTING - ON-BOARD .................8F-22
DIAGNOSTIC TROUBLE CODES - STANDARD PROCEDURE, OBTAINING .....8E-15
DIAGRAMS - 4XTE TRANSAXLE HYDRAULIC SCHEMATICS,
SCHEMATICS .................. 21-199,21-54
DIAGRAMS - DESCRIPTION, HOW TO USE WIRING ......................8W -01-1
DIAGRAMS - SPECIAL TOOLS, SCHEMATICS ........................ 21-68
DIESEL - DESCRIPTION ...............19-52
DIESEL - INSTALLATION ...............19-53
DIESEL - REMOVAL ................... 19-52
DIESEL ENGINE - DESCRIPTION, FUEL REQUIREMENTS .......................0-6
DIESEL ENGINES - DESCRIPTION, ENGINE OIL ...........................0-6
DIESEL ENGINES - EXPORT - DESCRIPTION ........................ 0-21
DIESEL ENGINES, INSTALLATION - 2.5L/2.8L ........................... 24-78
DIESEL ENGINES, REMOVAL - 2.5L/2.8L . . 24-77
DIFFERENTIAL BEARING PRELOAD - ADJUSTMENT ...................... 21-228
DIFFERENTIAL BEARING PRELOAD MEASUREMENT AND ADJUSTMENT,
ADJUSTMENTS ...................... 21-79
DIMENSIONS - FOLD-IN-FLOOR SEATS ONLY - SPECIFICATIONS, FRAME ........13-11
DIMENSIONS - SPECIFICATIONS, BODY OPENING .......................... 23-180
DIMENSIONS - SPECIFICATIONS, FRAME . . . 13-6
DIODE - INSTALLATION ............8W-01-14
DIODE - REMOVAL ................8W -01-14
DISABLED INDICATOR - DESCRIPTION, PASSENGER AIRBAG .................8O-33
DISABLED INDICATOR - INSTALLATION, PASSENGER AIRBAG .................8O-34
DISABLED INDICATOR - OPERATION, PASSENGER AIRBAG .................8O-33
DISABLED INDICATOR - REMOVAL, PASSENGER AIRBAG .................8O-34
DISASSEMBLY/ASSEMBLY - STANDARD PROCEDURE, TRANSMISSION COOLER
LINE QUICK CONNECT FITTING ...........7-38
DISC BRAKE CALIPER - INSTALLATION, REAR ............................... 5-30
DISC BRAKE CALIPER - REMOVAL, REAR ............................... 5-28
DISC BRAKE CALIPER ADAPTER - INSTALLATION, FRONT .................5-31DISC BRAKE CALIPER ADAPTER -
REMOVAL, FRONT ..................... 5-31
DISC BRAKE CALIPER (CONTINENTAL TEVES BRAKES) - INSTALLATION,
FRONT .............................. 5-27
DISC BRAKE CALIPER (CONTINENTAL TEVES BRAKES) - REMOVAL, FRONT ......5-24
DISC BRAKE CALIPER GUIDE PINS (TRW BRAKES) - INSTALLATION ...............5-32
DISC BRAKE CALIPER GUIDE PINS (TRW BRAKES) - REMOVAL .................. 5-31
DISC BRAKE CALIPER (TRW BRAKES) - INSTALLATION, FRONT .................5-27
DISC BRAKE CALIPER (TRW BRAKES) - REMOVAL, FRONT ..................... 5-24
DISC BRAKE SHOES - CLEANING .....5-16,5-18
DISC BRAKE SHOES - INSPECTION . . . 5-16,5-18
DISC BRAKE SHOES - INSTALLATION, REAR ............................... 5-19
DISC BRAKE SHOES - REMOVAL, REAR ....5-17
DISC BRAKE SHOES (CONTINENTAL TEVES BRAKES) - INSTALLATION,
FRONT .............................. 5-16
DISC BRAKE SHOES (CONTINENTAL TEVES BRAKES) - REMOVAL, FRONT ......5-15
DISC BRAKE SHOES (TRW BRAKES) - INSTALLATION, FRONT .................5-17
DISC BRAKE SHOES (TRW BRAKES) - REMOVAL, FRONT ..................... 5-15
DISC BRAKES (EXPORT) - DESCRIPTION . . . 5-13
DISC BRAKES (FRONT) - DESCRIPTION ....5-11
DISC BRAKES (FRONT) - OPERATION ......5-13
DISC BRAKES (REAR) - DESCRIPTION .....5-13
DISC BRAKES (REAR) - OPERATION ......5-14
DISCHARGE (ESD) SENSITIVE DEVICES - STANDARD PROCEDURE,
ELECTROSTATIC ...................8W -01-8
DISCHARGE LINE - INSTALLATION, A/C . . . 24-80
DISCHARGE LINE - REMOVAL, A/C .......24-79
DISPLAY - DESCRIPTION, PARK ASSIST . . . 8B-3
DISPLAY - INSTALLATION, PARK ASSIST . . . 8B-4
DISPLAY - OPERATION, PARK ASSIST .....8B-3
DISPLAY - REMOVAL, PARK ASSIST ......8B-4
DISPLAY TEST MODE, OPERATION - DRB III T STATE .......................... 25-10
DISSASEMBLY, REMOVAL ..............24-51
DISTRIBUTION DUCT - INSTALLATION ....24-57
DISTRIBUTION DUCT - REMOVAL ........24-57
DISTRIBUTION DUCTS - INSTALLATION, FLOOR ............................. 24-50
DISTRIBUTION DUCTS - REMOVAL, FLOOR ............................. 24-50
DISTRIBUTION SYSTEM - DESCRIPTION, POWER ..........................8W -97-1
DISTRIBUTION SYSTEM - OPERATION, POWER ..........................8W -97-1
DISTRIBUTION SYSTEMS, SPECIAL TOOLS - POWER ...................8W -97-1
DOES NOT FILL - DIAGNOSIS AND TESTING, VEHICLE ................... 25-17
DOME/CARGO LAMP - INSTALLATION ....8L-22
DOME/CARGO LAMP - REMOVAL ........8L-22
DOOR - INSTALLATION ................23-15
DOOR - INSTALLATION, FUEL FILL .......23-52
DOOR - INSTALLATION, SLIDING ........23-29
DOOR - REMOVAL .................... 23-15
DOOR - REMOVAL, FUEL FILL ..........23-52
DOOR - REMOVAL, SLIDING ............23-29
DOOR ACTUATOR - DESCRIPTION, BLEND ........................ 24-22,24-34
DOOR ACTUATOR - DESCRIPTION, MODE ............................. 24-29
DOOR ACTUATOR - DESCRIPTION, RECIRCULATION ..................... 24-31
DOOR ACTUATOR - INSTALLATION, BLEND ........................ 24-22,24-35
DOOR ACTUATOR - INSTALLATION, MODE ............................. 24-30
DOOR ACTUATOR - INSTALLATION, RECIRCULATION ..................... 24-32
DOOR ACTUATOR - OPERATION, BLEND . . 24-22,
24-35
DOOR ACTUATOR - OPERATION, MODE . . . 24-29
DOOR ACTUATOR - OPERATION, RECIRCULATION ..................... 24-31
DOOR ACTUATOR - REAR - DESCRIPTION, MODE .................24-39DOOR ACTUATOR - REAR -
INSTALLATION, MODE .................24-40
DOOR ACTUATOR - REAR - OPERATION, MODE ............................. 24-39
DOOR ACTUATOR - REAR - REMOVAL, MODE ............................. 24-39
DOOR ACTUATOR - REMOVAL, BLEND . . . 24-22, 24-35
DOOR ACTUATOR - REMOVAL, MODE ....24-29
DOOR ACTUATOR - REMOVAL, RECIRCULATION ..................... 24-32
DOOR ADJUSTMENT, STANDARD PROCEDURE - POWER SLIDING .........8N-49
DOOR ADJUSTMENTS, ADJUSTMENTS - SLIDING ............................ 23-30
DOOR BLOCKER LATCH - INSTALLATION, FUEL FILL .......................... 23-53
DOOR BLOCKER LATCH - REMOVAL, FUEL FILL .......................... 23-53
DOOR BLOCKER LATCH STRIKER - INSTALLATION, FUEL FILL .............23-53
DOOR BLOCKER LATCH STRIKER - REMOVAL, FUEL FILL .................23-53
DOOR BLOCKER LOCKOUT LINK - INSTALLATION, FUEL FILL .............23-54
DOOR BLOCKER LOCKOUT LINK - REMOVAL, FUEL FILL .................23-54
DOOR CONTROL MODULE - DESCRIPTION, SLIDING ...............8E-18
DOOR CONTROL MODULE - OPERATION, SLIDING ............................ 8E-18
DOOR CONTROL MODULE, DIAGNOSIS AND TESTING - SLIDING ...............8E-18
DOOR CYLINDER LOCK SWITCH - EXPORT - DESCRIPTION ...............8N-22
DOOR CYLINDER LOCK SWITCH - EXPORT - OPERATION ................8N-22
DOOR CYLINDER LOCK SWITCH, EXPORT ............................ 8N-22
DOOR GLASS - INSTALLATION ..........23-17
DOOR GLASS - INSTALLATION, SLIDING . 23-163
DOOR GLASS - REMOVAL .............23-16
DOOR GLASS - REMOVAL, SLIDING .....23-163
DOOR GLASS RUN WEATHERSTRIP - INSTALLATION, FRONT ...............23-166
DOOR GLASS RUN WEATHERSTRIP - REMOVAL, FRONT ................... 23-166
DOOR INNER BELT MOLDING - INSTALLATION, FRONT ...............23-168
DOOR INNER BELT MOLDING - REMOVAL, FRONT ................... 23-168
DOOR LEARN CYCLE, STANDARD PROCEDURE - POWER SLIDING .........8N-48
DOOR LOCK MOTOR - INSTALLATION, SLIDING ........................... 8N-25
DOOR LOCK MOTOR - REMOVAL, SLIDING ........................... 8N-25
DOOR LOCK MOTOR, DIAGNOSIS AND TESTING ........................... 8N-23
DOOR LOCK SWITCH, DIAGNOSIS AND TESTING ........................... 8N-23
DOOR MOTOR - DESCRIPTION, SLIDING . . 8N-51
DOOR MOTOR - INSTALLATION, SLIDING . 8N-51
DOOR MOTOR - OPERATION, SLIDING . . . 8N-51
DOOR MOTOR - REMOVAL, SLIDING .....8N-51
DOOR OUTER BELT MOLDING - INSTALLATION, FRONT ...............23-167
DOOR OUTER BELT MOLDING - REMOVAL, FRONT ................... 23-167
DOOR SILL PLATE - INSTALLATION, SLIDING ............................ 23-99
DOOR SILL PLATE - REMOVAL, SLIDING . . 23-98
DOOR SILL TRIM PLATE - INSTALLATION ....................... 23-89
DOOR SILL TRIM PLATE - REMOVAL .....23-89
DOOR STOP BUMPER BEZEL - INSTALLATION, SLIDING ...............23-25
DOOR STOP BUMPER BEZEL - REMOVAL, SLIDING .................. 23-25
DOOR SYSTEM - DESCRIPTION, POWER SLIDING ........................... 8N-40
DOOR SYSTEM - OPERATION, POWER SLIDING ........................... 8N-41
DOOR SYSTEM, DIAGNOSIS AND TESTING - POWER SLIDING ............8N-42
DOOR WEATHERSTRIP - INSTALLATION, FRONT ............................ 23-168
10 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

FOLD-IN-FLOOR - REMOVAL, SEATCUSHION COVER/FOAM - THIRD ROW . . . 23-159
FOLD-IN-FLOOR - REMOVAL, SEAT CUSHION COVER/FOAM -SECOND
ROW ............................. 23-136
FOLD-IN-FLOOR - REMOVAL, SEAT CUSHION SIDE SHIELD - SECOND
ROW ............................. 23-138
FOLD-IN-FLOOR - REMOVAL, SEAT GAS STRUT - SECOND ROW ...............23-138
FOLD-IN-FLOOR - REMOVAL, SEAT PROP ROD - SECOND ROW ................23-139
FOLD-IN-FLOOR - REMOVAL, SECOND ROW FLOOR TUB CARPET INSERT .......23-98
FOLD-IN-FLOOR - REMOVAL, SIDE SHIELD CUP HOLDER ................23-160
FOLD-IN-FLOOR - REMOVAL, WITH NVLD .............................. 25-20
FOLD-IN-FLOOR - SPECIFICATIONS, WELD LOCATIONS ................... 23-350
FOLD-IN-FLOOR ONLY - SPECIFICATIONS, BODY SEALING
LOCATIONS ........................ 23-209
FOLD-IN-FLOOR ONLY - SPECIFICATIONS, STRUCTURAL
ADHESIVE LOCATIONS ...............23-228
FOLD-IN-FLOOR SEATING - INSTALLATION .................... 5-68,5-75
FOLD-IN-FLOOR SEATING - INSTALLATION, FWD ................... 2-45
FOLD-IN-FLOOR SEATING - REMOVAL . 5-66,5-72
FOLD-IN-FLOOR SEATING - REMOVAL, FWD................................ 2-45
FOLD-IN-FLOOR SEATS ONLY - SPECIFICATIONS, FRAME DIMENSIONS .....13-11
FOLDING MECHANISM -SECOND ROW -FOLD-IN-FLOOR - INSTALLATION,
SEAT RECLINER/FORWARD ............23-137
FOLDING MECHANISM -SECOND ROW -FOLD-IN-FLOOR - REMOVAL, SEAT
RECLINER/FORWARD ................23-137
FORM-IN-PLACE GASKETS AND SEALERS, STANDARD PROCEDURE . . . 9-11,9-86
FORWARD MECHANISM -THIRD ROW -FOLD-IN-FLOOR - INSTALLATION,
SEAT RECLINER/FOLD ................23-160
FORWARD MECHANISM -THIRD ROW -FOLD-IN-FLOOR - REMOVAL, SEAT
RECLINER/FOLD .................... 23-160
FRAME - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION, SEAT BACK ....23-134
FRAME - SECOND ROW - FOLD-IN- FLOOR - REMOVAL, SEAT BACK ........23-134
FRAME - THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACK ..........23-157
FRAME - THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACK ..............23-156
FRAME DIMENSIONS - FOLD-IN-FLOOR SEATS ONLY - SPECIFICATIONS .........13-11
FRAME DIMENSIONS - SPECIFICATIONS . . . 13-6
FREE MODULE - INSTALLATION, HANDS . . . 8T-3
FREE MODULE - REMOVAL, HANDS .......8T-3
FRONT - DESCRIPTION, HALF SHAFT .......3-1
FRONT - DESCRIPTION, PLUMBING ......24-65
FRONT - INSTALLATION, BUSHING - LEAF SPRING ........................ 2-30
FRONT - INSTALLATION, CRANKSHAFT OIL SEAL ....................... 9-130,9-42
FRONT - INSTALLATION, HALF SHAFT ......3-4
FRONT - INSTALLATION, SEAT BELT & RETRACTOR - OUTBOARD .............8O-39
FRONT - INSTALLATION, SPRING MOUNTS ............................ 2-43
FRONT - INSTALLATION, WHEEL MOUNTING STUDS ................... 22-21
FRONT - OPERATION, PLUMBING ........24-65
FRONT - REMOVAL, BUSHING - LEAF SPRING ............................. 2-29
FRONT - REMOVAL, CRANKSHAFT OIL SEAL .......................... 9-130,9-41
FRONT - REMOVAL, HALF SHAFT ..........3-2
FRONT - REMOVAL, SEAT BELT & RETRACTOR - OUTBOARD .............8O-38
FRONT - REMOVAL, SPRING MOUNTS .....2-42
FRONT - REMOVAL, WHEEL MOUNTING STUDS ............................. 22-21
FRONT - SPECIFICATIONS, HALF SHAFT ....3-6FRONT A/C EXPANSION VALVE,
DIAGNOSIS AND TESTING .............24-82
FRONT BLOWER MOTOR, DIAGNOSIS AND TESTING ....................... 24-46
FRONT BLOWER MOTOR RESISTOR BLOCK, DIAGNOSIS AND TESTING .......24-25
FRONT BRAKE ROTOR - INSTALLATION ....5-59
FRONT BRAKE ROTOR - REMOVAL .......5-59
FRONT BUMPER REINFORCEMENT - INSTALLATION ........................ 13-3
FRONT BUMPER REINFORCEMENT - REMOVAL ........................... 13-3
FRONT CABLE - INSTALLATION, PARKING BRAKE LEVER ................5-77
FRONT CABLE - REMOVAL, PARKING BRAKE LEVER ........................ 5-77
FRONT CENTER BEZEL OUTLETS, INSTALLATION ....................... 24-45
FRONT CENTER BEZEL OUTLETS, REMOVAL .......................... 24-44
FRONT CONTROL MODULE - DESCRIPTION ........................ 8E-7
FRONT CONTROL MODULE - OPERATION . . 8E-7
FRONT CONTROL MODULE, DIAGNOSIS AND TESTING ........................ 8E-7
FRONT CRADLE CROSSMEMBER - DESCRIPTION ....................... 13-14
FRONT CRADLE CROSSMEMBER THREAD REPAIR - DESCRIPTION ........13-14
FRONT CROSSMEMBER MOUNT BUSHINGS - INSTALLATION ............13-17
FRONT CROSSMEMBER MOUNT BUSHINGS - REMOVAL .................13-17
FRONT DEMISTER OUTLETS, INSTALLATION ....................... 24-45
FRONT DEMISTER OUTLETS, REMOVAL . . . 24-44
FRONT DISC BRAKE CALIPER ADAPTER - INSTALLATION ...................... 5-31
FRONT DISC BRAKE CALIPER ADAPTER - REMOVAL .......................... 5-31
FRONT DISC BRAKE CALIPER (CONTINENTAL TEVES BRAKES) -
INSTALLATION ........................ 5-27
FRONT DISC BRAKE CALIPER (CONTINENTAL TEVES BRAKES) -
REMOVAL ........................... 5-24
FRONT DISC BRAKE CALIPER (TRW BRAKES) - INSTALLATION ...............5-27
FRONT DISC BRAKE CALIPER (TRW BRAKES) - REMOVAL .................. 5-24
FRONT DISC BRAKE SHOES (CONTINENTAL TEVES BRAKES) -
INSTALLATION ........................ 5-16
FRONT DISC BRAKE SHOES (CONTINENTAL TEVES BRAKES) -
REMOVAL ........................... 5-15
FRONT DISC BRAKE SHOES (TRW BRAKES) - INSTALLATION ...............5-17
FRONT DISC BRAKE SHOES (TRW BRAKES) - REMOVAL .................. 5-15
FRONT DOOR GLASS RUN WEATHERSTRIP - INSTALLATION .......23-166
FRONT DOOR GLASS RUN WEATHERSTRIP - REMOVAL ...........23-166
FRONT DOOR INNER BELT MOLDING - INSTALLATION ...................... 23-168
FRONT DOOR INNER BELT MOLDING - REMOVAL ......................... 23-168
FRONT DOOR OUTER BELT MOLDING - INSTALLATION ...................... 23-167
FRONT DOOR OUTER BELT MOLDING - REMOVAL ......................... 23-167
FRONT DOOR WEATHERSTRIP - INSTALLATION ...................... 23-168
FRONT DOOR WEATHERSTRIP - REMOVAL ......................... 23-168
FRONT FASCIA - INSTALLATION ..........13-1
FRONT FASCIA - REMOVAL ..............13-1
FRONT FENDER - INSTALLATION ........23-52
FRONT FENDER - REMOVAL ............23-51
FRONT FOG LAMP - DIAGNOSIS AND TESTING ............................ 8L-7
FRONT FOG LAMP - INSTALLATION .......8L-8
FRONT FOG LAMP - REMOVAL ...........8L-8
FRONT FOG LAMP UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE .......8L-9
FRONT FOG LAMP UNIT ALIGNMENT - STANDARD PROCEDURE ................8L-9FRONT HEATER CORE, INSTALLATION
....24-86
FRONT HEATER CORE, REMOVAL ........24-85
FRONT HEATER CORE TUBES, INSTALLATION ....................... 24-85
FRONT HEATER CORE TUBES, REMOVAL . . 24-84
FRONT INBOARD - INSTALLATION, SEAT BELT BUCKLE ....................... 8O-35
FRONT INBOARD - REMOVAL, SEAT BELT BUCKLE ....................... 8O-35
FRONT MOUNT - INSTALLATION ....9-134,9-50
FRONT MOUNT - REMOVAL ........9-134,9-50
FRONT SEAT - INSTALLATION ..........23-110
FRONT SEAT - REMOVAL .............23-108
FRONT SEAT BACK - INSTALLATION .....23-111
FRONT SEAT BACK - REMOVAL ........23-111
FRONT SEAT BACK ASSIST STRAP - INSTALLATION ...................... 23-112
FRONT SEAT BACK ASSIST STRAP - REMOVAL ......................... 23-112
FRONT SEAT BACK COVER - INSTALLATION ...................... 23-116
FRONT SEAT BACK COVER - REMOVAL . . 23-113
FRONT SEAT BACK PANEL - INSTALLATION ...................... 23-113
FRONT SEAT BACK PANEL - REMOVAL . . 23-112
FRONT SEAT CUSHION - INSTALLATION . . 23-118
FRONT SEAT CUSHION - OCS - INSTALLATION ...................... 23-120
FRONT SEAT CUSHION - OCS - REMOVAL ........................... 23-119
FRONT SEAT CUSHION - REMOVAL .....23-117
FRONT SEAT CUSHION SIDE COVER - INSTALLATION ...................... 23-121
FRONT SEAT CUSHION SIDE COVER - OCS - INSTALLATION ................23-122
FRONT SEAT CUSHION SIDE COVER - OCS - REMOVAL .................... 23-121
FRONT SEAT CUSHION SIDE COVER - REMOVAL ......................... 23-120
FRONT SEAT RISER - MANUAL - OCS - INSTALLATION ...................... 23-123
FRONT SEAT RISER - MANUAL - OCS - REMOVAL ......................... 23-123
FRONT SEAT TRACK - REAR COVER - INSTALLATION ...................... 23-128
FRONT SEAT TRACK - REAR COVER - REMOVAL ......................... 23-128
FRONT SEAT TRACK ADJUSTER/MANUAL - OCS - INSTALLATION ...............23-128
FRONT SEAT TRACK ADJUSTER/MANUAL - OCS - REMOVAL ................... 23-126
FRONT SEAT TRACK ADJUSTER/POWER - OCS - INSTALLATION ...............23-125
FRONT SEAT TRACK ADJUSTER/POWER - OCS - REMOVAL ................... 23-124
FRONT SEAT TRACK MANUAL ADJUSTER - INSTALLATION ...........23-126
FRONT SEAT TRACK MANUAL ADJUSTER - REMOVAL ...............23-125
FRONT SEAT TRACK POWER ADJUSTER - INSTALLATION .................... 23-124
FRONT SEAT TRACK POWER ADJUSTER - REMOVAL ........................ 23-124
FRONT SEAT TRACK REAR COVER - OCS - INSTALLATION .................... 23-129
FRONT SEAT TRACK REAR COVER - OCS - REMOVAL ........................ 23-129
FRONT SUSPENSION - DESCRIPTION ......2-2
FRONT SUSPENSION - OPERATION ........2-2
FRONT SUSPENSION FASTENER TORQUE, SPECIFICATIONS ...............2-3
FRONT SUSPENSION, SPECIAL TOOLS .....2-3
FRONT WHEEL SPEED SENSOR - INSTALLATION ........................ 5-92
FRONT WHEEL SPEED SENSOR - REMOVAL ........................... 5-91
FRONT WHEELHOUSE SPLASH SHIELD - INSTALLATION ....................... 23-57
FRONT WHEELHOUSE SPLASH SHIELD - REMOVAL .......................... 23-57
FRONT WIPER ARM ALIGNMENT - STANDARD PROCEDURE ...............8R-9
FRONT WIPER ARMS - INSTALLATION ....8R-9
FRONT WIPER ARMS - REMOVAL ........8R-9
FRONT WIPER MOTOR - INSTALLATION . . 8R-10
FRONT WIPER MOTOR - REMOVAL .......8R-9
FRONT WIPER SYSTEM - DIAGNOSIS AND TESTING ........................ 8R-2
14 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

HYDRAULIC CIRCUITS AND VALVES -OPERATION .......................... 5-95
HYDRAULIC LASH ADJUSTER NOISE DIAGNOSIS - DIAGNOSIS AND
TESTING ............................ 9-34
HYDRAULIC LASH ADJUSTERS - INSTALLATION ........................ 9-35
HYDRAULIC LASH ADJUSTERS - REMOVAL ........................... 9-35
HYDRAULIC LIFTERS - DIAGNOSIS AND TESTING ........................... 9-116
HYDRAULIC LIFTERS (CAM IN BLOCK) - DESCRIPTION ....................... 9-116
HYDRAULIC LIFTERS (CAM IN BLOCK) - INSTALLATION ....................... 9-117
HYDRAULIC LIFTERS (CAM IN BLOCK) - REMOVAL .......................... 9-117
HYDRAULIC PRESSURE TESTS - DIAGNOSIS AND TESTING ........21-150,21-6
HYDRAULIC SCHEMATICS, SCHEMATICS AND DIAGRAMS - 4XTE TRANSAXLE ....21-199,
21-54
HYDROSTATIC LOCKED ENGINE, STANDARD PROCEDURE ............9-10,9-87
ICU - ASSEMBLY ..................... 5-106
ICU - DISASSEMBLY ..................5-105
ICU (INTEGRATED CONTROL UNIT) - DESCRIPTION ....................... 5-102
ICU (INTEGRATED CONTROL UNIT) - OPERATION ......................... 5-102
IDENTIFICATION - DESCRIPTION, VEHICLE ............................ 23-1
IDENTIFICATION AND INFORMATION - DESCRIPTION, SECTION ..............8W-01-6
IDLE AIR CONTROL MOTOR - DESCRIPTION ....................... 14-33
IDLE AIR CONTROL MOTOR - INSTALLATION ....................... 14-33
IDLE AIR CONTROL MOTOR - OPERATION ......................... 14-33
IDLE AIR CONTROL MOTOR - REMOVAL . . 14-33
IGNITION COIL - DESCRIPTION ...........8I-6
IGNITION COIL - OPERATION .............8I-6
IGNITION SENSE - PCM INPUT - OPERATION ......................... 8E-14
IGNITION SWITCH - INSTALLATION ......19-19
IGNITION SWITCH - REMOVAL ..........19-17
IGNITION SYSTEM - DESCRIPTION ........8I-1
IGNITION SYSTEM - OPERATION ..........8I-1
IGNITION-OFF DRAW TEST, STANDARD PROCEDURE ........................ 8F-13
ILLUMINATION LAMPS - INSTALLATION, CLUSTER ........................... 8L-21
ILLUMINATION LAMPS - REMOVAL, CLUSTER ........................... 8L-21
IMPACT SENSOR - DESCRIPTION .......8O-18
IMPACT SENSOR - INSTALLATION .......8O-21
IMPACT SENSOR - REMOVAL ...........8O-19
INBOARD - 50/50 BENCH - INSTALLATION, SEAT BELT BUCKLE -
SECOND ROW ....................... 8O-38
INBOARD - 50/50 BENCH - REMOVAL, SEAT BELT BUCKLE - SECOND ROW .....8O-37
INBOARD - INSTALLATION, SEAT BELT BUCKLE - FRONT .................... 8O-35
INBOARD - QUAD BUCKET - INSTALLATION, SEAT BELT BUCKLE -
FIRST ROW ......................... 8O-36
INBOARD - QUAD BUCKET - REMOVAL, SEAT BELT BUCKLE - FIRST ROW .......8O-35
INBOARD - REMOVAL, SEAT BELT BUCKLE - FRONT .................... 8O-35
INDICATOR - DESCRIPTION, PASSENGER AIRBAG DISABLED ................... 8O-33
INDICATOR - INSTALLATION, PASSENGER AIRBAG DISABLED .........8O-34
INDICATOR - OPERATION, PASSENGER AIRBAG DISABLED ................... 8O-33
INDICATOR - REMOVAL, PASSENGER AIRBAG DISABLED ................... 8O-34
INDICATOR LAMP - DESCRIPTION, VTSS/SKIS .......................... 8Q-8
INDICATOR LAMP - OPERATION, VTSS/SKIS .......................... 8Q-8
INDICATORS - DIAGNOSIS AND TESTING, TREAD WEAR ...............22-16
INFLATABLE KNEE - INSTALLATION, BLOCKER ........................... 23-75INFLATABLE KNEE - REMOVAL,
BLOCKER ........................... 23-75
INFLATION PRESSURES - STANDARD PROCEDURE, TIRE ................... 22-16
INFO CENTER - DESCRIPTION, ELECTRONIC VEHICLE .................8M-7
INFO CENTER - OPERATION, ELECTRONIC VEHICLE .................8M-7
INFRARED TEMPERATURE SENSOR - DESCRIPTION ....................... 24-28
INFRARED TEMPERATURE SENSOR - OPERATION ......................... 24-28
INITIAL OPERATION - STANDARD PROCEDURE, POWER STEERING
PUMP ............................. 19-37
INJECTION SYSTEM - OPERATION .......14-22
INJECTOR - DESCRIPTION, FUEL ........14-30
INJECTOR - OPERATION, FUEL ..........14-31
INLET AIR TEMPERATURE SENSOR - DESCRIPTION ....................... 14-34
INLET FILTER - INSTALLATION ..........14-17
INLET FILTER - REMOVAL ..............14-17
INLET HOSE - INSTALLATION, HEATER ....24-87
INLET HOSE - REMOVAL, HEATER .......24-86
INLET TUBE - 2.4L - DESCRIPTION, WATER PUMP ........................ 7-36
INLET TUBE - 2.4L - INSTALLATION, WATER PUMP ........................ 7-36
INLET TUBE - 2.4L - REMOVAL, WATER PUMP .............................. 7-36
INLET TUBE - 3.3/3.8L - INSTALLATION, WATER PUMP ......................... 7-37
INLET TUBE - 3.3/3.8L - REMOVAL, WATER PUMP ........................ 7-37
INNER - INSTALLATION, CV BOOT .........3-7
INNER - REMOVAL, CV BOOT .............3-6
INNER BELT MOLDING - INSTALLATION, FRONT DOOR ...................... 23-168
INNER BELT MOLDING - REMOVAL, FRONT DOOR ...................... 23-168
INPUT - DESCRIPTION, SPEED SENSOR . 21-120, 21-271
INPUT - INSTALLATION, SPEED SENSOR ..................... 21-121,21-272
INPUT - OPERATION, DATA BUS COMMUNICATION RECEIVE - PCM .......8E-14
INPUT - OPERATION, IGNITION SENSE - PCM............................... 8E-14
INPUT - OPERATION, SENSOR RETURN - PCM............................... 8E-14
INPUT - OPERATION, SPEED SENSOR . . . 21-120, 21-271
INPUT - REMOVAL, SPEED SENSOR ....21-121,
21-272
INPUT CLUTCH ASSEMBLY - ASSEMBLY . 21-246, 21-95
INPUT CLUTCH ASSEMBLY - DISASSEMBLY ................. 21-237,21-86
INSERT - FOLD-IN-FLOOR - INSTALLATION, REAR FLOOR TUB
CARPETS ........................... 23-96
INSERT - FOLD-IN-FLOOR - INSTALLATION, SECOND ROW FLOOR
TUB CARPET ........................ 23-98
INSERT - FOLD-IN-FLOOR - REMOVAL, REAR FLOOR TUB CARPETS ............23-95
INSERT - FOLD-IN-FLOOR - REMOVAL, SECOND ROW FLOOR TUB CARPET ......23-98
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-1
INSTRUMENT CLUSTER - OPERATION .....8J-1
INSTRUMENT PANEL - INSTALLATION, LOWER ............................ 23-73
INSTRUMENT PANEL - REMOVAL, LOWER ............................ 23-73
INSTRUMENT PANEL ANTENNA CABLE - INSTALLATION ....................... 8A-12
INSTRUMENT PANEL ANTENNA CABLE - REMOVAL .......................... 8A-12
INSTRUMENT PANEL ASSEMBLY - INSTALLATION ....................... 23-70
INSTRUMENT PANEL ASSEMBLY - REMOVAL .......................... 23-67
INSTRUMENT PANEL CENTER BEZEL - INSTALLATION ....................... 23-72
INSTRUMENT PANEL CENTER BEZEL - REMOVAL .......................... 23-71
INSTRUMENT PANEL DEMISTER DUCTS - INSTALLATION ..................... 24-54INSTRUMENT PANEL DEMISTER DUCTS
- REMOVAL ......................... 24-54
INSTRUMENT PANEL DUCTS - INSTALLATION ....................... 24-55
INSTRUMENT PANEL DUCTS - REMOVAL . 24-55
INSTRUMENT PANEL OUTLETS, INSTALLATION ....................... 24-45
INSTRUMENT PANEL OUTLETS, REMOVAL .......................... 24-45
INSTRUMENT PANEL RIGHT END CAP - INSTALLATION ....................... 23-72
INSTRUMENT PANEL RIGHT END CAP - REMOVAL .......................... 23-72
INSTRUMENT PANEL TOP COVER - INSTALLATION ....................... 23-72
INSTRUMENT PANEL TOP COVER - REMOVAL .......................... 23-72
INSTRUMENT PANEL TOP PAD ASSEMBLY - INSTALLATION ............23-77
INSTRUMENT PANEL TOP PAD ASSEMBLY - REMOVAL ................23-77
INTAKE MANIFOLD - DESCRIPTION . . 9-147,9-60
INTAKE MANIFOLD - INSTALLATION, LOWER ............................ 9-151
INTAKE MANIFOLD - INSTALLATION, UPPER ............................. 9-149
INTAKE MANIFOLD - LOWER - CLEANING .......................... 9-151
INTAKE MANIFOLD - LOWER - INSPECTION .................... 9-151,9-62
INTAKE MANIFOLD - LOWER - INSTALLATION ........................ 9-62
INTAKE MANIFOLD - LOWER - REMOVAL ....9-62
INTAKE MANIFOLD - REMOVAL, LOWER . . 9-150
INTAKE MANIFOLD - REMOVAL, UPPER . . . 9-148
INTAKE MANIFOLD - UPPER - INSPECTION ......................... 9-61
INTAKE MANIFOLD - UPPER - INSTALLATION ........................ 9-61
INTAKE MANIFOLD - UPPER - REMOVAL . . . 9-60
INTAKE MANIFOLD LEAKS - DIAGNOSIS AND TESTING ................... 9-147,9-60
INTAKE MANIFOLD VACUUM PORT REPAIR - STANDARD PROCEDURE .......9-148
INTAKE PIPE - INSTALLATION, AIR ......24-115
INTAKE PIPE - REMOVAL, AIR .........24-115
INTAKE/EXHAUST VALVES & SEATS - CLEANING ...................... 9-108,9-33
INTAKE/EXHAUST VALVES & SEATS - DESCRIPTION ................... 9-107,9-33
INTAKE/EXHAUST VALVES & SEATS - INSPECTION ........................ 9-108
INTAKE/EXHAUST VALVES & SEATS - INSTALLATION ....................... 9-109
INTAKE/EXHAUST VALVES & SEATS - OPERATION ......................... 9-107
INTAKE/EXHAUST VALVES & SEATS - REMOVAL .......................... 9-108
INTEGRAL ANTENNA - EXPORT - DESCRIPTION, QUARTER GLASS ........8A-13
INTEGRAL ANTENNA - EXPORT - OPERATION, QUARTER GLASS ..........8A-13
INTEGRAL ANTENNA, EXPORT - QUARTER GLASS .................... 8A-13
INTEGRATED POWER MODULE - DESCRIPTION .....................8W -97-1
INTEGRATED POWER MODULE - INSTALLATION ....................8W -97-2
INTEGRATED POWER MODULE - OPERATION .......................8W -97-2
INTEGRATED POWER MODULE - REMOVAL ........................8W -97-2
INTERACTIVE SPEED CONTROL (4 SPEED EATX ONLY) - OPERATION ........8P-2
INTERFACE (PCI) BUS, OPERATION - PROGRAMMABLE COMMUNICATIONS ....14-25
INTERIOR LAMPS, SPECIFICATIONS ......8L-20
INTERLOCK SOLENOID - DESCRIPTION, SHIFT ....................... 21-113,21-264
INTERLOCK SOLENOID - DIAGNOSIS AND TESTING, BRAKE/TRANSMISSION
SHIFT ....................... 21-115,21-266
INTERLOCK SOLENOID - INSTALLATION, SHIFT ....................... 21-116,21-267
INTERLOCK SOLENOID - OPERATION, SHIFT ....................... 21-114,21-265
INTERLOCK SOLENOID - REMOVAL, SHIFT ....................... 21-115,21-266
RS INDEX17
Description Group-Page Description Group-Page Description Group-Page

OCS - REMOVAL, FRONT SEAT CUSHION . 23-119
OCS - REMOVAL, FRONT SEAT CUSHIONSIDE COVER ....................... 23-121
OCS - REMOVAL, FRONT SEAT RISER - MANUAL .......................... 23-123
OCS - REMOVAL, FRONT SEAT TRACK ADJUSTER/MANUAL .................23-126
OCS - REMOVAL, FRONT SEAT TRACK ADJUSTER/POWER .................. 23-124
OCS - REMOVAL, FRONT SEAT TRACK REAR COVER ....................... 23-129
OIL - DESCRIPTION, FLEXIBLE FUEL ENGINE ..............................0-3
OIL - DESCRIPTION, REFRIGERANT ......24-94
OIL - DIESEL ENGINES - DESCRIPTION, ENGINE ..............................0-6
OIL - OPERATION, REFRIGERANT ........24-94
OIL AND FILTER CHANGE - STANDARD PROCEDURE, ENGINE .............9-139,9-54
OIL AND LUBRICANTS - DESCRIPTION, ENGINE ..............................0-1
OIL COOLER - DESCRIPTION, TRANSMISSION ....................... 7-39
OIL COOLER - INSPECTION, TRANSMISSION ....................... 7-39
OIL COOLER & LINES - DESCRIPTION ....9-141
OIL COOLER & LINES - INSTALLATION . . . 9-141
OIL COOLER & LINES - OPERATION ......9-141
OIL COOLER & LINES - REMOVAL .......9-141
OIL COOLER LINES - INSTALLATION, TRANSMISSION ....................... 7-40
OIL COOLER LINES - REMOVAL, TRANSMISSION ....................... 7-39
OIL FILTER - DESCRIPTION .............9-54
OIL FILTER - INSTALLATION ........9-141,9-54
OIL FILTER - REMOVAL ............9-141,9-54
OIL FILTER ADAPTER - INSTALLATION ....9-142
OIL FILTER ADAPTER - REMOVAL .......9-142
OIL GALLERY PLUGS - STANDARD PROCEDURE, ENGINE CORE .........9-10,9-88
OIL LEAK INSPECTION - DIAGNOSIS AND TESTING, ENGINE ..............9-8,9-84
OIL LEVEL CHECK - STANDARD PROCEDURE, ENGINE .................9-140
OIL LEVEL CHECK, STANDARD PROCEDURE - ENGINE .................9-54
OIL LEVEL, STANDARD PROCEDURE - REFRIGERANT ....................... 24-94
OIL PAN - CLEANING .................9-142
OIL PAN - INSPECTION ................9-143
OIL PAN - INSTALLATION ..........9-143,9-55
OIL PAN - REMOVAL ..............9-142,9-55
OIL PRESSURE - DIAGNOSIS AND TESTING, CHECKING ENGINE ............9-53
OIL PRESSURE - DIAGNOSIS AND TESTING, ENGINE .................... 9-138
OIL PRESSURE RELIEF VALVE - INSTALLATION ....................... 9-144
OIL PRESSURE RELIEF VALVE - REMOVAL .......................... 9-143
OIL PRESSURE SWITCH - DESCRIPTION . . 9-144
OIL PRESSURE SWITCH - INSTALLATION . 9-144, 9-56
OIL PRESSURE SWITCH - OPERATION ....9-144
OIL PRESSURE SWITCH - REMOVAL . 9-144,9-56
OIL PUMP - ASSEMBLY ...........9-146,9-58
OIL PUMP - ASSEMBLY ........21-112,21-263
OIL PUMP - CLEANING ............9-145,9-57
OIL PUMP - DESCRIPTION .............9-144
OIL PUMP - DESCRIPTION ......21-110,21-261
OIL PUMP - DISASSEMBLY ........9-145,9-57
OIL PUMP - DISASSEMBLY ......21-110,21-261
OIL PUMP - INSPECTION ..........9-145,9-58
OIL PUMP - INSTALLATION ........9-146,9-59
OIL PUMP - INSTALLATION, SEAL ......21-113,
21-264
OIL PUMP - OPERATION ........21-110,21-261
OIL PUMP - REMOVAL ............9-144,9-56
OIL PUMP - REMOVAL, SEAL ....21-113,21-264
OIL SEAL - FRONT - INSTALLATION, CRANKSHAFT ................... 9-130,9-42
OIL SEAL - FRONT - REMOVAL, CRANKSHAFT ................... 9-130,9-41
OIL SEAL - REAR - INSTALLATION, CRANKSHAFT ................... 9-131,9-42
OIL SEAL - REAR - REMOVAL, CRANKSHAFT ................... 9-131,9-42OIL SEAL RETAINER - INSTALLATION,
CRANKSHAFT REAR .................. 9-132
OIL SEAL RETAINER - REMOVAL, CRANKSHAFT REAR .................. 9-132
OIL SEAL(S) - INSTALLATION, CAMSHAFT .......................... 9-29
OIL SEAL(S) - REMOVAL, CAMSHAFT .....9-28
ON-BOARD DIAGNOSTIC SYSTEM, DIAGNOSIS AND TESTING ..............8F-22
ONLY - SPECIFICATIONS, BODY SEALING LOCATIONS - FOLD-IN-FLOOR .........23-209
ONLY - SPECIFICATIONS, FRAME DIMENSIONS - FOLD-IN-FLOOR SEATS . . . 13-11
ONLY - SPECIFICATIONS, STRUCTURAL ADHESIVE LOCATIONS - FOLD-IN-
FLOOR ............................ 23-228
OPEN LATCH - INSTALLATION, HOLD .....23-25
OPEN LATCH - REMOVAL, HOLD ........23-25
OPEN LATCH CABLE - INSTALLATION, HOLD .............................. 23-38
OPEN LATCH CABLE - REMOVAL, HOLD . . . 23-38
OPEN LATCH STRIKER - INSTALLATION, HOLD .............................. 23-26
OPEN LATCH STRIKER - REMOVAL, HOLD .............................. 23-26
OPEN SWITCH - DESCRIPTION, FULL ....8N-11,
8N-52
OPEN SWITCH - INSTALLATION, FULL ....8N-11
OPEN SWITCH - OPERATION, FULL . 8N-11,8N-52
OPEN SWITCH - REMOVAL, FULL .......8N-11
OPEN-CIRCUIT VOLTAGE TEST, STANDARD PROCEDURE ................8F-13
OPENING DIMENSIONS - SPECIFICATIONS, BODY ..............23-180
ORVR - OPERATION ..................25-15
OUTER BELT MOLDING - INSTALLATION, FRONT DOOR ...................... 23-167
OUTER BELT MOLDING - REMOVAL, FRONT DOOR ...................... 23-167
OUTER TIE ROD - INSTALLATION ........19-35
OUTER TIE ROD - REMOVAL ...........19-34
OUTLET - DESCRIPTION, POWER ......8W-97-3
OUTLET - DIAGNOSIS & TESTING, POWER ..........................8W -97-3
OUTLET - OPERATION, POWER .......8W-97-3
OUTLETS - DESCRIPTION, AIR .....24-43,24-56
OUTLETS - INSTALLATION, AIR .........24-56
OUTLETS - REMOVAL, AIR .............24-56
OUTLETS, INSTALLATION - FRONT CENTER BEZEL ...................... 24-45
OUTLETS, INSTALLATION - FRONT DEMISTER .......................... 24-45
OUTLETS, INSTALLATION - INSTRUMENT PANEL ............................. 24-45
OUTLETS, REMOVAL - FRONT CENTER BEZEL ............................. 24-44
OUTLETS, REMOVAL - FRONT DEMISTER . 24-44
OUTLETS, REMOVAL - INSTRUMENT PANEL ............................. 24-45
OUTPUT - DESCRIPTION, SPEED SENSOR ..................... 21-122,21-273
OUTPUT - INSTALLATION, SPEED SENSOR ..................... 21-123,21-274
OUTPUT - OPERATION, 5 VOLT SUPPLY - PCM............................... 8E-15
OUTPUT - OPERATION, SPEED SENSOR . 21-122, 21-273
OUTPUT - REMOVAL, SPEED SENSOR . . 21-123,
21-274
OUTSIDE HANDLE - INSTALLATION ......23-36
OUTSIDE HANDLE - REMOVAL ..........23-35
OUTSIDE HANDLE CABLE - INSTALLATION ....................... 23-37
OUTSIDE HANDLE CABLE - REMOVAL ....23-37
OVER STEERING COLUMN COVER - INSTALLATION ....................... 23-76
OVER STEERING COLUMN COVER - REMOVAL .......................... 23-76
OVERHEAD CONSOLE - DESCRIPTION ....8M-2
OVERHEAD CONSOLE, DIAGNOSIS AND TESTING ............................ 8M-3
OVERHEAD CONSOLE, SPECIAL TOOLS . . . 8M-7
PAD - INSTALLATION, REAR FASCIA - SCUFF .............................. 13-5
PAD - REMOVAL, REAR FASCIA - SCUFF . . . 13-5
PAD ASSEMBLY - INSTALLATION, INSTRUMENT PANEL TOP ..............23-77PAD ASSEMBLY - REMOVAL,
INSTRUMENT PANEL TOP ..............23-77
PAINT CODE - DESCRIPTION ..........23-101
PAINTED TOUCH-UP - DESCRIPTION ....23-101
PAN - CLEANING, OIL .................9-142
PAN - INSPECTION, OIL ...............9-143
PAN - INSTALLATION, OIL .........9-143,9-55
PAN - REMOVAL, OIL .............9-142,9-55
PAN PANEL-THIRD ROW - FOLD-IN- FLOOR - INSTALLATION, BOTTOM OF
SEAT CUSHION ..................... 23-152
PAN PANEL-THIRD ROW - FOLD-IN- FLOOR - REMOVAL, BOTTOM OF SEAT
CUSHION .......................... 23-152
PANEL - INSTALLATION, BENCH SEAT BACK ............................. 23-144
PANEL - INSTALLATION, FRONT SEAT BACK ............................. 23-113
PANEL - INSTALLATION, GLASS ........23-173
PANEL - INSTALLATION, LEFT D-PILLAR TRIM .............................. 23-94
PANEL - INSTALLATION, LEFT QUARTER TRIM .............................. 23-94
PANEL - INSTALLATION, LOWER INSTRUMENT ....................... 23-73
PANEL - INSTALLATION, RIGHT D-PILLAR TRIM ...................... 23-98
PANEL - INSTALLATION, RIGHT QUARTER TRIM ...................... 23-97
PANEL - INSTALLATION, TRIM .....23-20,23-34,
23-43
PANEL - REMOVAL, BENCH SEAT BACK . . . 23-143
PANEL - REMOVAL, FRONT SEAT BACK . . 23-112
PANEL - REMOVAL, GLASS ............23-173
PANEL - REMOVAL, LEFT D-PILLAR TRIM .............................. 23-94
PANEL - REMOVAL, LEFT QUARTER TRIM .............................. 23-94
PANEL - REMOVAL, LOWER INSTRUMENT ....................... 23-73
PANEL - REMOVAL, RIGHT D-PILLAR TRIM .............................. 23-97
PANEL - REMOVAL, RIGHT QUARTER TRIM .............................. 23-97
PANEL - REMOVAL, TRIM ....23-20,23-34,23-43
PANEL - SECOND ROW -FOLD-IN-FLOOR - INSTALLATION, SEAT BACK ..........23-134
PANEL - SECOND ROW -FOLD-IN-FLOOR - REMOVAL, SEAT BACK ..............23-134
PANEL - THIRD ROW -FOLD-IN-FLOOR - INSTALLATION, SEAT BACK ............23-158
PANEL - THIRD ROW -FOLD-IN-FLOOR - REMOVAL, SEAT BACK ...............23-158
PANEL ADJUSTMENT, ADJUSTMENTS - SUNROOF GLASS ................... 23-173
PANEL ANTENNA CABLE - INSTALLATION, INSTRUMENT ...........8A-12
PANEL ANTENNA CABLE - REMOVAL, INSTRUMENT ....................... 8A-12
PANEL ASSEMBLY - INSTALLATION, INSTRUMENT ....................... 23-70
PANEL ASSEMBLY - REMOVAL, INSTRUMENT ....................... 23-67
PANEL CENTER BEZEL - INSTALLATION, INSTRUMENT ....................... 23-72
PANEL CENTER BEZEL - REMOVAL, INSTRUMENT ....................... 23-71
PANEL DEMISTER DUCTS - INSTALLATION, INSTRUMENT ...........24-54
PANEL DEMISTER DUCTS - REMOVAL, INSTRUMENT ....................... 24-54
PANEL DUCTS - INSTALLATION, INSTRUMENT ....................... 24-55
PANEL DUCTS - REMOVAL, INSTRUMENT ....................... 24-55
PANEL OUTLETS, INSTALLATION - INSTRUMENT ....................... 24-45
PANEL OUTLETS, REMOVAL - INSTRUMENT ....................... 24-45
PANEL REPAIR - STANDARD PROCEDURE, PLASTIC BODY ............23-3
PANEL RIGHT END CAP - INSTALLATION, INSTRUMENT ....................... 23-72
PANEL RIGHT END CAP - REMOVAL, INSTRUMENT ....................... 23-72
PANEL TOP COVER - INSTALLATION, INSTRUMENT ....................... 23-72
22 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

QUAD BUCKET - REMOVAL, BUCKETSEAT BACK ........................ 23-140
QUAD BUCKET - REMOVAL, SEAT BELT BUCKLE - FIRST ROW INBOARD ........8O-35
QUAD BUCKET, 50/50 SPLIT, BENCH - INSTALLATION, SEAT BACK HINGE
COVERS ........................... 23-146
QUAD BUCKET, 50/50 SPLIT, BENCH - INSTALLATION, SEAT CUSHION COVER . . 23-144
QUAD BUCKET, 50/50 SPLIT, BENCH - REMOVAL, SEAT BACK HINGE COVERS . . 23-146
QUAD BUCKET, 50/50 SPLIT, BENCH - REMOVAL, SEAT CUSHION COVER ......23-144
QUAD BUCKET SEAT RISER - INSTALLATION ...................... 23-143
QUAD BUCKET SEAT RISER - REMOVAL . 23-143
QUAD BUCKET SEAT SIDE SHIELD - NO CUP HOLDER - INSTALLATION .........23-143
QUAD BUCKET SEAT SIDE SHIELD - NO CUP HOLDER - REMOVAL .............23-143
QUAD BUCKET SEAT SIDE SHIELD/CUP HOLDER - FLAP AND SPRING
ASSEMBLY - INSTALLATION ...........23-151
QUAD BUCKET SEAT SIDE SHIELD/CUP HOLDER - FLAP AND SPRING
ASSEMBLY - REMOVAL ...............23-151
QUAD BUCKET SEAT SIDE SHIELD/CUP HOLDER - INSTALLATION .............23-142
QUAD BUCKET SEAT SIDE SHIELD/CUP HOLDER - REMOVAL .................23-141
QUAD CHILD SEAT - INSTALLATION .....23-106
QUAD CHILD SEAT - REMOVAL ........23-106
QUAD SEAT CUSHION - INSTALLATION . . 23-141
QUAD SEAT CUSHION - REMOVAL ......23-141
QUARTER GLASS INTEGRAL ANTENNA - EXPORT - DESCRIPTION ...............8A-13
QUARTER GLASS INTEGRAL ANTENNA - EXPORT - OPERATION ................8A-13
QUARTER GLASS INTEGRAL ANTENNA, EXPORT ............................ 8A-13
QUARTER PANEL/FENDER AIR EXHAUSTER - DESCRIPTION, REAR ......23-59
QUARTER PANEL/FENDER AIR EXHAUSTER - INSTALLATION, REAR .....23-60
QUARTER PANEL/FENDER AIR EXHAUSTER - REMOVAL, REAR .........23-59
QUARTER TRIM BOLSTER - INSTALLATION ....................... 23-95
QUARTER TRIM BOLSTER - REMOVAL ....23-95
QUARTER TRIM PANEL - INSTALLATION, LEFT .............................. 23-94
QUARTER TRIM PANEL - INSTALLATION, RIGHT ............................. 23-97
QUARTER TRIM PANEL - REMOVAL, LEFT .............................. 23-94
QUARTER TRIM PANEL - REMOVAL, RIGHT ............................. 23-97
QUARTER WINDOW - INSTALLATION ....23-164
QUARTER WINDOW - REMOVAL ........23-164
QUICK CONNECT FITTING DISASSEMBLY/ASSEMBLY -
STANDARD PROCEDURE,
TRANSMISSION COOLER LINE ...........7-38
QUICK LEARN PROCEDURE - STANDARD PROCEDURE ........................ 8E-15
QUICK-CONNECT FITTINGS - STANDARD PROCEDURE ........................ 14-18
RACK - DESCRIPTION, LOWER DRIVE UNIT TRACK ........................ 8N-57
RACK - INSTALLATION, LOWER DRIVE UNIT TRACK ........................ 8N-58
RACK - OPERATION, LOWER DRIVE UNIT TRACK ............................. 8N-57
RACK - REMOVAL, LOWER DRIVE UNIT TRACK ............................. 8N-57
RACK CROSSBAR - INSTALLATION, LUGGAGE .......................... 23-59
RACK CROSSBAR - REMOVAL, LUGGAGE . 23-58
RACK RISER - INSTALLATION, LUGGAGE . . 23-58
RACK RISER - REMOVAL, LUGGAGE .....23-57
RADIAL-PLY TIRES - DESCRIPTION ......22-13
RADIATOR - INSTALLATION .............7-27
RADIATOR - REMOVAL .................7-26
RADIATOR CAP TO FILLER NECK SEAL - DIAGNOSIS AND TESTING ..............7-28
RADIATOR CROSSMEMBER - INSTALLATION, UPPER ................23-56RADIATOR CROSSMEMBER - REMOVAL,
UPPER ............................. 23-56
RADIATOR DRAINCOCK - INSTALLATION . . . 7-27
RADIATOR DRAINCOCK - REMOVAL .......7-27
RADIATOR FAN - DESCRIPTION ..........7-29
RADIATOR FAN - INSTALLATION ..........7-30
RADIATOR FAN - OPERATION ............7-29
RADIATOR FAN - REMOVAL .............7-30
RADIATOR FAN MOTOR - DIAGNOSIS AND TESTING ........................ 7-30
RADIATOR FAN RELAY - DESCRIPTION ....7-31
RADIATOR FAN RELAY - INSTALLATION ....7-31
RADIATOR FAN RELAY - OPERATION ......7-31
RADIATOR FAN RELAY - REMOVAL .......7-31
RADIATOR PRESSURE CAP - DESCRIPTION ........................ 7-27
RADIATOR PRESSURE CAP - OPERATION . . 7-27
RADIO - DESCRIPTION ................8A-13
RADIO - INSTALLATION, ANTENNA - NAVIGATION ........................ 8A-11
RADIO - OPERATION ..................8A-14
RADIO - REMOVAL, ANTENNA - NAVIGATION ........................ 8A-11
RADIO, DIAGNOSIS AND TESTING .......8A-14
RADIO NOISE SUPPRESSION COMPONENTS - DESCRIPTION ..........8A-15
RADIO NOISE SUPPRESSION COMPONENTS - OPERATION ...........8A-15
RANGE - SPECIFICATIONS, TRANSMITTER ...................... 8N-24
RANGE SENSOR - DESCRIPTION, TRANSMISSION ............... 21-130,21-281
RANGE SENSOR - INSTALLATION, TRANSMISSION ............... 21-131,21-282
RANGE SENSOR - OPERATION, TRANSMISSION ............... 21-131,21-282
RANGE SENSOR - REMOVAL, TRANSMISSION ............... 21-131,21-282
READING LAMP - INSTALLATION ........8L-23
READING LAMP - REMOVAL ............8L-22
RECEIVER / DRIER - DESCRIPTION ......24-92
RECEIVER / DRIER - INSTALLATION ......24-93
RECEIVER / DRIER - OPERATION ........24-92
RECEIVER / DRIER - REMOVAL .........24-92
RECIRCULATION DOOR ACTUATOR - DESCRIPTION ....................... 24-31
RECIRCULATION DOOR ACTUATOR - INSTALLATION ....................... 24-32
RECIRCULATION DOOR ACTUATOR - OPERATION ......................... 24-31
RECIRCULATION DOOR ACTUATOR - REMOVAL .......................... 24-32
RECLINER HANDLE - INSTALLATION ....23-108
RECLINER HANDLE - REMOVAL ........23-108
RECLINER/FOLD FORWARD MECHANISM -THIRD ROW -FOLD-IN-FLOOR -
INSTALLATION, SEAT .................23-160
RECLINER/FOLD FORWARD MECHANISM -THIRD ROW -FOLD-IN-FLOOR -
REMOVAL, SEAT .................... 23-160
RECLINER/FORWARD FOLDING MECHANISM -SECOND ROW
-FOLD-IN-FLOOR - INSTALLATION,
SEAT ............................. 23-137
RECLINER/FORWARD FOLDING MECHANISM -SECOND ROW
-FOLD-IN-FLOOR - REMOVAL, SEAT .....23-137
RECOVERY CONTAINER - DESCRIPTION, COOLANT ............................ 7-20
RECOVERY CONTAINER - INSTALLATION, COOLANT ............................ 7-20
RECOVERY CONTAINER - OPERATION, COOLANT ............................ 7-20
RECOVERY CONTAINER - REMOVAL, COOLANT ............................ 7-20
RECOVERY, STANDARD PROCEDURE - REFRIGERANT SYSTEM ...............24-70
RECOVERY SYSTEM - DIAGNOSIS AND TESTING, COOLANT ................... 7-20
REFACING VALVES AND VALVE SEATS - STANDARD PROCEDURE ...............9-107
REFRIGERANT - DESCRIPTION ..........24-93
REFRIGERANT - OPERATION ............24-94
REFRIGERANT LINES, INSTALLATION - UNDERBODY ....................... 24-112
REFRIGERANT LINES, REMOVAL - UNDERBODY ....................... 24-110
REFRIGERANT OIL - DESCRIPTION ......24-94 REFRIGERANT OIL - OPERATION
........24-94
REFRIGERANT OIL LEVEL, STANDARD PROCEDURE ........................ 24-94
REFRIGERANT SYSTEM CHARGE, STANDARD PROCEDURE ...............24-71
REFRIGERANT SYSTEM EVACUATE, STANDARD PROCEDURE ...............24-70
REFRIGERANT SYSTEM LEAKS, DIAGNOSIS AND TESTING .............24-67
REFRIGERANT SYSTEM RECOVERY, STANDARD PROCEDURE ...............24-70
REFRIGERANT SYSTEM SERVICE EQUIPMENT, STANDARD PROCEDURE ....24-69
REGULATOR - DESCRIPTION, VOLTAGE . . . 8F-30
REGULATOR - INSTALLATION, FUEL PRESSURE .......................... 14-7
REGULATOR - MANUAL - INSTALLATION, WINDOW ........................... 23-23
REGULATOR - MANUAL - REMOVAL, WINDOW ........................... 23-22
REGULATOR - OPERATION, FUEL PRESSURE .......................... 14-7
REGULATOR - OPERATION, VOLTAGE .....8F-30
REGULATOR - POWER - INSTALLATION, WINDOW ........................... 23-22
REGULATOR - POWER - REMOVAL, WINDOW ........................... 23-22
REGULATOR - REMOVAL, FUEL PRESSURE .......................... 14-7
REINFORCEMENT - INSTALLATION, FRONT BUMPER ...................... 13-3
REINFORCEMENT - INSTALLATION, REAR BUMPER .............................. 13-5
REINFORCEMENT - REMOVAL, FRONT BUMPER ............................ 13-3
REINFORCEMENT - REMOVAL, REAR BUMPER ............................ 13-5
RELAY - DESCRIPTION, A/C COMPRESSOR CLUTCH ...............24-18
RELAY - DESCRIPTION, AUTO SHUT DOWN .............................. 8I-3
RELAY - DESCRIPTION, BLOWER MOTOR ....................... 24-23,24-36
RELAY - DESCRIPTION, FUEL PUMP .....14-32
RELAY - DESCRIPTION, RADIATOR FAN ....7-31
RELAY - DESCRIPTION, REAR WINDOW DEFOGGER .......................... 8G-3
RELAY - DESCRIPTION, TRANSMISSION CONTROL ................... 21-130,21-281
RELAY - INSTALLATION, A/C COMPRESSOR CLUTCH ...............24-19
RELAY - INSTALLATION, BLOWER MOTOR ....................... 24-24,24-37
RELAY - INSTALLATION, RADIATOR FAN . . . 7-31
RELAY - INSTALLATION, REAR WINDOW DEFOGGER .......................... 8G-4
RELAY - OPERATION, A/C COMPRESSOR CLUTCH ............................ 24-18
RELAY - OPERATION, AUTO SHUT DOWN . . . 8I-3
RELAY - OPERATION, BLOWER MOTOR . . 24-23, 24-36
RELAY - OPERATION, FUEL PUMP .......14-32
RELAY - OPERATION, RADIATOR FAN ......7-31
RELAY - OPERATION, REAR WINDOW DEFOGGER .......................... 8G-3
RELAY - OPERATION, TRANSMISSION CONTROL ................... 21-130,21-281
RELAY - REMOVAL, A/C COMPRESSOR CLUTCH ............................ 24-19
RELAY - REMOVAL, BLOWER MOTOR ....24-24,
24-37
RELAY - REMOVAL, RADIATOR FAN .......7-31
RELAY - REMOVAL, REAR WINDOW DEFOGGER .......................... 8G-4
RELEASE - STANDARD PROCEDURE, PARKING BRAKE AUTOMATIC
ADJUSTER TENSION ................... 5-63
RELEASE CABLE - INSTALLATION, LATCH . 23-64
RELEASE CABLE - REMOVAL, LATCH .....23-63
RELEASE PROCEDURE - STANDARD PROCEDURE, FUEL SYSTEM
PRESSURE .......................... 14-2
RELIEF VALVE - INSTALLATION, OIL PRESSURE ......................... 9-144
RELIEF VALVE - REMOVAL, OIL PRESSURE ......................... 9-143
RELIEF VALVE, DESCRIPTION - HIGH PRESSURE ......................... 24-72
RS INDEX25
Description Group-Page Description Group-Page Description Group-Page