2005 Acura TSX Owner's Manual

Open the hood. To change a bulb
on the driver’s side, undo the
three fasteners and remove the air
intake cover.Remove the electrical connector
f rom the bulb by pulling the
connector straight back.
Remove the rubber weather seal
by pulling on the tab.Unclip the end of the hold-down
wire f rom its slot. Pivot it out of
the way and remove the bulb.
Insert the new bulb into the hole,
making sure the tabs are in their
slots. Pivot the hold-down wire
back in place, and clip the end into
the slot.
Install the rubber weather seal
over the back of the headlight
assembly.Makesureitisright
side up; it is marked with an arrow.
1. 2.
3.6. 4.
5.
Lights
216
FASTENER
AIR INTAKE COVER
HOLD-DOWN WIREBULB
CONNECTOR
RUBBER WEATHER SEAL

Open the hood.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to test the new
bulb.
Push the electrical connector onto
the new bulb. Make sure it is
connected securely.
Turn on the headlights to test the
new bulb.
On the driver’s side, reinstall the
air intake cover. Reinstall the
three fasteners and secure them
by pushing on the heads until they
lock. 3.
4.
5.
2. 1.
7.
8.
9.
Replacing the Front Side Marker/
Turn Signal Light Bulb
Lights
Maint enance
217
SOCKET

To change the bulb on the driver’s
side, start the engine, turn the
steering wheel all the way to the
right, and turn of f the engine. To
change the bulb on the passenger’s
side, turn the steering wheel to the
lef t.Use a f lat-tipped screwdriver to
remove the two holding clips f rom
the inner f ender.
Pull the inner f ender cover away
f rom the f ender and bumper.Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
4. 5.
2.
1.
3.
Replacing a Front Parking L ight
Bulb
Lights
218
HOLDING CLIPS

Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to test the new
bulb.
Put the inner f ender cover in place.
Install and lock each holding clip
bypushingonthecenter.Open the trunk.
Remove the light assembly cover
by pulling its outside edge.
Remove the socket by turning it
one-quarter turn counterclockwise,
and pull the bulb straight out of its
socket.Push a new bulb straight into the
socket until it bottoms, and
reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Test the new bulb to make sure it
works.
Reinstall the light assembly cover.
1.
3. 2.
6.
7.
8.
4.
5.
6.
Lights
Replacing Rear Bulbs
(in Fenders)
Maint enance
219
COVER

Open the trunk.
To replace a bulb on the lef t side,
remove the two trim clips. On the
right side, remove a trim clip.
Pull the lining back caref ully.Determine which of the two bulbs
is burned out: taillight or back-up
light.Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
1.
2. 5.
6.
4.
3. Replacing Rear Bulbs
(in T runk L id)
Lights
220
TRIM CLIPS SOCKETSBULBS

Reinstall the trunk lid trim. Make
sure it is installed under the edge
of the trunk lid seal.
Press the trim clips back into their
holes.
Insert the socket back into the
light assembly. Turn it clockwise
to lock it in place.
Turn on the lights to test the new
bulb.
Open the trunk and remove the
socket f rom the light assembly by
turning it one-quarter turn counter-
clockwise.
Remove the burned-out bulb by
pulling it straight out of the socket.
Install the new bulb and reinstall
the socket. Make sure the new
bulb is working.
7.
8.
9.
10.
1.
2.
3.
Lights
Replacing a High-mount Brake
Light Bulb
Maint enance
221

Each outside mirror has side turn
signal lights. The lights should be
replaced by your Acura dealer.The license plate has two lights
above it. The bulbs should be
replaced by your Acura dealer.
Lights
Side T urn Signal L ight
Rear L icense Plate Bulb
222

Dirt build-up in the loops of the seat
belt anchors can cause the belts to
retract slowly. Wipe the insides of
the loops with a clean cloth
dampened in mild soap and warm
water or isopropyl alcohol.If you use aftermarket floor mats
make sure they f it properly and that
theycanbeusedwiththefloormat
anchors. Do not put additional f loor
mats on top of the anchored mats.
This f ilter removes the dust and
pollenthatisbroughtinfromthe
outside through the heating and
cooling system/climate control
system.
Clean dirty seat belts with a sof t
brush and a mixture of mild soap and
warm water. Do not use bleach, dye,
or cleaning solvents that can weaken
the belt material. Let the belts air
drybeforeyouusethevehicle. The driver’s f loor mat that came
with your vehicle hook over the f loor
mat anchors. This keeps the f loor
mats f rom sliding f orward and
possibly interf ering with the pedals.
If you remove the f loor mats, make
sure to re-anchor them when you put
them back in your vehicle.Have your Acura dealer replace this
f ilter every 30,000 miles (48,000 km)
under normal conditions. It should
be replaced every 15,000 miles
(24,000 km) if you drive primarily in
urban areas that have high
concentrations of soot in the air, or if
the airf low f rom the climate control
system becomes less than usual.
Seat Belts, Floor Mats, Dust and Pollen Filter
Seat Belts
Floor Mats
Dust and Pollen Filter
Maint enance
223
LOOP