Page 73 of 288

If the system repeatedly does not
recognize the coding of your key,
contact your dealer.
Do not attempt to alter this system
or add other devices to it. Electrical
problems could result that may make
your vehicle undriveable.
If you lose your key and you cannot
start the engine, contact your dealer.
The Immobilizer System protects
your vehicle f rom thef t. If an
improperly-coded key (or other
device) is used, the engine will not
start.
When you turn the ignition switch to
ON (II), the Immobilizer System
indicator should come on f or a f ew
seconds, then go out. If the indicator
starts to blink, it means the system
does not recognize the coding of the
key. Turn the ignition switch to
LOCK (0), remove the key, reinsert
it, and turn the switch to ON (II)
again.
The system may not recognize your
key’s coding if another immobilizer
key or other metal object (i.e. key
f ob) is near the ignition switch when
you insert the key.As required by the FCC:
This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
Immobilizer Syst em
72
Page 74 of 288
µµµ
µ
You can insert or
remove the key only in this position.
To turn the key, the shift lever must
be in Park, and you must push the
key in slightly. If the f ront wheels
are turned, the anti-thef t lock may
make it difficult to turn the key.
Firmly turn the steering wheel to the
left or to the right as you turn the
key.
The ignition switch has f our
positions: LOCK (0), ACCESSORY
(I), ON (II), START (III) You can
operate the audio system and the
accessory power sockets in this
position.
This is the normal key
position when driving. Several of the
lights on the instrument panel come
on as a test when you turn the
ignition switch f rom ACCESSORY
(I) to ON (II).
Use this position
only to start the engine. The switch
returns to ON (II) when you let go of
the key.
CONT INUED
L OCK (0) A CCESSORY (I)
ON (II)
ST A RT (III)
Ignition Switch
Inst rument s and Cont rols
73
Page 75 of 288

You will hear a reminder beeper if
you leave the key in the ignition
switch in the LOCK (0) or
ACCESSORY (I) position and open
thedriver’sdoor.Removethekeyto
turn of f the beeper.
If your vehicle has an automatic
transmission, the shif t lever must be
in Park bef ore you can remove the
key f rom the ignition switch.Each door has a lock tab on the top.
Push the tab down to lock the door
and pull it up to unlock.To lock any passenger’s door when
getting out of the vehicle, push the
lock tab down and close the door. To
lock the driver’s door, pull and hold
the outside door handle then push
the lock tab down. Release the
handle, then close the door.
To lock any passenger’s door when
getting out of the vehicle, push the
lock tab down, and close the door.
Door L ocks
Ignit ion Swit ch, Door L ocks
74
LOCK TAB
Removing the key from the
ignition switch while driving
locks the steering. This can
cause you to lose control of the
vehicle.
Remove the key from the
ignition switch only when
parked.
Page 76 of 288
With the driver’s door open and the
key in the ignition, both door lock
switches are disabled. They are not
disabled if the driver’s door is closed.
Pushing the switch down on the
open passenger’s door will lock all
doors. Youcanopenorclosethewindows
by using the key in the driver’s door
(see page ).
Each f ront door has a master door
lock switch. Either switch locks and
unlocks all doors. On the driver’s
door, push the top of the master
door lock switch to lock all doors,;
push the bottom to unlock them. On the f ront passenger’s door, push
the master door lock switch down to
lock the all doors, and up to unlock
them. 91
L ockout Prevent ion
Power Door L ocks
Door L ocks
Inst rument s and Cont rols
75
MASTER DOOR LOCK SWITCH
MASTER DOOR LOCK SWITCH
bottom top
Page 77 of 288

µ
µ You can open and close all power
windows from outside the vehicle
with the key. With the remote
transmitter, you can open the
windows. Refer to Power Windows
on page .
The ceiling light (if the ceiling light
switch is in the center position) will
come on when you press the
UNLOCK button. If you do not open
any door, the light stays on f or about
30 seconds, then f ades out. If you
relock the doors with the remote
transmitter before 30 seconds have
elapsed, the light will go of f
immediately.
Pressthisbuttononce
to unlock the driver’s door. Push it
twice to unlock the other doors.
The childproof door locks are
designed to prevent children seated
in the rear f rom accidentally opening
the rear doors. Each rear door has a
lock lever near the edge. With the
lever in the LOCK position, the door
cannot be opened f rom the inside
regardless of the position of the lock
tab. To open the door, pull the lock
tab up, and use the outside door
handle. Press this button once to
lock all doors. Some exterior and
interior lights will f lash. You cannot
lock it if any door is not f ully closed
or key is in the ignition switch.
When you push LOCK twice within 5
seconds, you will hear a beep to
verify that the security system has
set. 91
Remote Transmitter
UNL OCK
Childproof Door L ocks
LOCK
Childproof Door L ocks, Remot e T ransmit t er
76
PANIC
BUTTON
LEVER LED
TRUNK
RELEASE
BUTTONLOCK
BUTTON
UNLOCK
BUTTON
Page 78 of 288

µµ
You cannot lock the doors with the
remote transmitter if any door is not
f ully closed or the key is in the
ignition switch.
Avoid dropping or throwing the
transmitter.
Protect the transmitter from
extreme temperature.
Do not immerse the transmitter in
any liquid.
If you lose a transmitter, the
replacement needs to be
reprogrammed by your dealer.
If you unlock the doors with the
remote transmitter, but do not open
any of the doors within 30 seconds,
the doors automatically relock and
the security system will also set.
To open the trunk, push the Trunk
Release button f or about 1 second.
The trunk will not open if the key is
in the ignition switch. Pressthisbuttonfor
about 1 second to attract attention;
thehornwillsoundandtheexterior
lights will f lash f or about 30 seconds.
To cancel panic mode, press any
other button on the remote
transmitter, or turn the ignition
switch to ON (II).
Pressthisbuttonfor
about 1 second to open the trunk.
You cannot open the trunk if the key
is in the ignition switch.
CONT INUED
Remote Transmitter CarePA NIC
TRUNK
Remote Transmitter
Inst rument s and Cont rols
77
Page 79 of 288
µ
If it takes several pushes on the
button to lock or unlock the doors,
replace the battery as soon as
possible.
To replace the battery:
Battery type: CR2025
Place a cloth on the edge of the
transmitter, and remove the upper
half by caref ully prying on the
edge with a small f lat-tip
screwdriver.Remove the old battery and note
the polarity. Make sure the
polarity of the new battery is the
same ( side f acing up), then
insert it in the transmitter.
Snapthetwohalvesof the
transmitter case back together.
1.
2.
3.
Replacing the Transmitter Battery
Remote Transmitter
78
BATTERY
Page 80 of 288
As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
Remote Transmitter
Inst rument s and Cont rols
79