2005 Acura RL lock

Pour the coolant slowly and caref ully
so you do not spill. Clean up any spill
immediately; it could damage
components in the engine
compartment.The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
When the radiator and engine are
cool, relieve any pressure in the
cooling system by turning the
radiator cap counterclockwise,
without pressing down.
Remove the radiator cap by
pushing down and turning
counterclockwise. Put the radiator cap back on, and
tighten it fully.
Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
Do not add any rust inhibitors or
other additives to your vehicle’s
cooling system. They may not be
compatible with the coolant or
engine components.
3.
1.
2. 4.
5.
Engine Coolant
Maint enance
309
RADIATOR CAP
RESERVE TANK

µµ
In very high temperatures
(over 110°F, 43°C).
In very low temperatures
(under 20°F, 29°C).
If you f requently tow a trailer.
The timing belt should be replaced
at the intervals shown on the
maintenance minder. Replace the
belt at 60,000 miles (100,000 km) if
you regularly drive your vehicle in
one or more of these conditions:
Power Steering Fluid, Timing Belt
Timing Belt
Maint enance
313
T urning the steering wheel to f ull lef t
or right lock and holding it there can
damage the power steering pump.

CONT INUED
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it one-
quarter turn counterclockwise.
Remove the left or right side
engine compartment cover f rom
thesideyouareworkingonby
caref ully pulling the cover out (see
page ).
If youarereplacingthebulbon
the driver’s side, remove the
battery cover (see page ), then
remove the battery hold-down by
removing the two nuts with a10
mm wrench. Then caref ully slide
the battery toward the engine to
access the bulb. 2.
3.
304
332
1.
Lights
Maint enance
315
NUTS
BULB
BATTERY HOLD-DOWN

Insert the new bulb into the hole
and turn it one-quarter turn clock-
wise to lock it in place.
Turn on the headlights to test the
new bulb.
(Driver’s side)
Reinstall the engine compartment
side cover. Push the electrical connector back
onto the bulb. Make sure it is on
all the way.Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Push the bulb in slightly, and turn
it counterclockwise.
Reinstall the battery in the reverse
order of removal, and reinstall the
cover on the battery. Remove the left or right side
engine compartment cover f rom
thesideyouareworkingonby
caref ully pulling the cover out (see
page ).
If you are replacing a driver’s side
bulb, slide the battery toward the
engine to get more clearance (see
page ).
2.
1.
4.
5.
6.
7.
8.
3.
304
332
Lights
Replacing a Front T urn Signal
Bulb
316
SOCKET
BULB

Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
(Driver’s side)Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.
Remove the left or right side
engine compartment cover (see
page ).
(Passenger’s side)
Use a f lat-tipped screwdriver to
remove the holding clip f rom the
windshield washer reservoir. If you are replacing a driver’s side
bulb, slide the battery toward the
engine to get more clearance (see
page ).
Reinstall the battery and the
battery cover.
Reinstall the engine compartment
side cover. 1.
2.
4.
5.
6.
7.
8.
3.
4.
304
332
CONT INUED
Lights
Replacing a Front Position/Side
Marker L ight Bulb
Maint enance
317
BULB
HOLDING CLIP

Use a Phillips-head screwdriver to
remove the two mounting bolts
and remove the holding clip with a
f lat-tipped screwdriver.
Caref ully push up the side under
cover into the bumper.
Your vehicle uses halogen light
bulbs. When replacing a bulb, handle
it by its plastic case and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
(Driver’s side)
Reinstall the battery and the
battery cover.
Reinstall the windshield washer
reservoir. (Passenger’s side)
Reinstall the engine compartment
side cover.
1.
2.
5.
6.
7.
8.
9.
Lights
Replacing a Front Fog L ight Bulb
318
BOLTS
CLIP
Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.

Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it one-
quarter turn counterclockwise.Insert the new bulb into the hole
and turn it one-quarter turn clock-
wise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the f og lights to test the
new bulb.
Reinstall the two mounting bolts
on the side under cover and
tighten them securely. Put the
holding clip back on the side
under cover and push on the
centre until it locks (the centre is
flushwiththehead).
3.
4. 5.
6.
8. 7.
Lights
Maint enance
319
BULB

Determine which of the two bulbs
is burned out: turn signal or back-
up light.
Remove the socket by turning it
one-quarter turn counterclockwise.
Remove the burned out bulb by
pulling it straight out of its socket.
Open the trunk lid, and remove
the lef t or right maintenance lid.
Remove the mounting nut with an
8mmwrench.
Carefully pry in the top or bottom
edge of the with a small flat-tipped
screwdriver, and pull the trim
straight back.
Remove the two mounting bolts
with an 8 mm wrench.
Pull the taillight assembly straight
back out of the body.
2. 1.
3.
4.
5.6.
7.
8.
Lights
Replacing Rear Bulbs
320
MOUNTING NUT
MAINTENANCE LID BOLTS
BULBS
TAIL LIGHT TRIM