2004 YAMAHA YZF-R1S oil

5-31
VALVES AND VALVE SPRINGSENG
CAUTION:
NOTE:
a. Apply a coarse lapping compound a to the
valve face.
Do not let the lapping compound enter the
gap between the valve stem and the valve
guide.
b. Apply molybdenum disulfide oil onto the
valve stem.
c. Install the valve into the cylinder head.
d. Turn the valve until the valve face and valve
seat are evenly polished, then clean off all of
the lapping compound.
For the best lapping results, lightly tap the valve
seat while rotating the valve back and forth be-
tween your hands.
e. Apply a fine lapping compound to the valve
face and repeat the above steps.
f. After every lapping procedure, be sure to
clean off all of the lapping compound from
the valve face and valve seat.
g. Apply Mechanic’s blueing dye (Dykem) onto
the valve face.
h. Install the valve into the cylinder head.
i. Press the valve through the valve guide and
onto the valve seat to make a clear impres-
sion.
j. Measure the valve seat width
a again. If the
valve seat width is out of specification, reface
and lap the valve seat.
EAS00241
CHECKING THE VALVE SPRINGS
The following procedure applies to all of the
valve springs.
1. Measure:

valve spring free length
a
Out of specification
Replace the valve
spring.
Valve spring free length
Intake valve spring
39.3 mm (1.55 in)
: 37.3 mm (1.47 in)
Exhaust valve spring
39.3 mm (1.55 in)
: 37.3 mm (1.47 in)
ProCarManuals.com

5-32
VALVES AND VALVE SPRINGSENG
2. Measure:

compressed valve spring force
a
Out of specification
Replace the valve
spring.
bInstalled length
Compressed valve spring force
(installed)
Intake valve spring
145.9
167.9 N
(14.88
17.12 kg,
32.80
37.74 lb) at
32.65 mm (1.285 in)
Exhaust valve spring
164.1
188.9 N
(16.73
19.26 kg,
36.89
42.46 lb) at
32.82 mm (12.92 in)
3. Measure:

valve spring tilt
a
Out of specification
Replace the valve
spring.
Spring tilt limit
Intake valve spring
1.7 mm (0.07 in)
Exhaust valve spring
1.7 mm (0.07 in)
EAS00242
CHECKING THE VALVE LIFTERS
The following procedure applies to all of the
valve lifters.
1. Check:

valve lifter
Damage / scratches
Replace the valve lift-
ers and cylinder head.
EAS00245
INSTALLING THE VALVES
The following procedure applies to all of the
valves and related components.
1. Deburr:

valve stem end
(with an oil stone)
ProCarManuals.com

5-33
VALVES AND VALVE SPRINGSENG
NOTE:
NOTE:
NOTE:
2. Lubricate:

valve stem
1

valve stem seal 2
(with the recommended lubricant)
Recommended lubricant
Molybdenum disulfide oil
3. Install:

valve
1

lower spring seat 2

valve stem seal 3

valve spring 4

upper spring seat 5
(into the cylinder head)
Install the valve spring with the larger pitch
a
facing up.
bSmaller pitch
Make sure that each valve is installed in its origi-
nal place. Refer to the following embossed
marks.
Right and left intake valve(-s): “5VY :”
Middle intake valve(-s): “5VY
.”
Exhaust valve(-s): “5VY”
4. Install:

valve cotters
1
Install the valve cotters by compressing the
valve spring with the valve spring compressor
2 and the valve spring compressor attachment
3.
Valve spring compressor
90890-04019, YM-04019
Valve spring compressor
attachment
Intake valve
90890-04114, YM-4114
Exhaust valve
90890-04108, YM-4108
ProCarManuals.com

5-34
VALVES AND VALVE SPRINGSENG
CAUTION:
NOTE: 5. To secure the valve cotters onto the valve
stem, lightly tap the valve tip with a soft-face
hammer.
Hitting the valve tip with excessive force
could damage the valve.
6. Install:

valve pad
1

valve lifter 2

Lubricate the valve lifter and valve pad with
molybdenum disulfide oil.

The valve lifter must move smoothly when ro-
tated with a finger.

Each valve lifter and valve pad must be rein-
stalled in its original position.
ProCarManuals.com

5-35
Order Job / Part Q’ty Remarks
1
2
3
4
5
6
7
8
9Removing the stator coil assembly
Rider seat
Fuel tank
Left side cowling
Bottom cowlings
Engine oil
Stator coil assembly lead coupler
Plug
Generator rotor cover
Gasket
Dowel pin
Generator rotor assembly
Dowel pin
Bearing housing
Collar1
1
1
1
2
1
2
1
1Remove the parts in the order listed.
Refer to “SEATS” in chapter 3.
Refer to “FUEL TANK” in chapter 3.
Refer to “COWLINGS” in chapter 3.
Drain.
Refer to “CHANGING THE ENGINE OIL”
in chapter 3.
Disconnect.
10 Nm (1.0 m
kg, 7.2 ft
lb)
12 Nm (1.2 m
kg, 8.7 ft
lb)
12 Nm (1.2 m
kg, 8.7 ft
lb)
12 Nm (1.2 m
kg, 8.7 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
14 Nm (1.4 m
kg, 10 ft
lb)
22 Nm (2.2 m
kg, 16 ft
lb)
22 Nm (2.2 m
kg, 16 ft
lb)
STARTER CLUTCH AND GENERATORENG
STARTER CLUTCH AND GENERATOR
STATOR COIL ASSEMBLY
ProCarManuals.com

5-36
STARTER CLUTCH AND GENERATORENG
Order Job / Part Q’ty Remarks
10
11
12
13
14
15Bearing
Stator coil assembly lead holder
Idler gear
Idler gear shaft
Washer
Bearing1
1
1
1
1
1
For installation, reverse the removal
procedure.
10 Nm (1.0 m
kg, 7.2 ft
lb)
12 Nm (1.2 m
kg, 8.7 ft
lb)
12 Nm (1.2 m
kg, 8.7 ft
lb)
12 Nm (1.2 m
kg, 8.7 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
14 Nm (1.4 m
kg, 10 ft
lb)
22 Nm (2.2 m
kg, 16 ft
lb)
22 Nm (2.2 m
kg, 16 ft
lb)
ProCarManuals.com

5-38
STARTER CLUTCH AND GENERATORENG
NOTE: REMOVING THE GENERATOR
1. Remove:

rider seat

fuel tank
Refer to “SEATS” and “FUEL TANK” in chapter
3.
2. Remove:

left side cowling

bottom cowlings
Refer to “COWLINGS” in chapter 3.
3. Drain:

engine oil
Refer to “CHANGING THE ENGINE OIL” in
chapter 3.
4. Remove:

plug

generator rotor cover
1

While pushing generator rotor, remove the
generator rotor cover.

Loosen each bolt 1 / 4 of a turn a time, in stages
and in a crisscross pattern.

After all of the bolts are fully loosened, remove
them.
5. Remove:

generator rotor and starter clutch assembly
1.
6. Remove:

idler gear shaft bolt
1

idler shaft

idler gear
2
ProCarManuals.com

5-41
STARTER CLUTCH AND GENERATORENG
NOTE:
NOTE:
10 Nm (1.0 m
kg, 7.2 ft
lb)
INSTALLING THE STARTER CLUTCH
1. Install:

generator rotor
1

damper 2

driven gear 3

The hole side of the damper is installed to the
generator side.

Lubricate the engine oil
4.
2. Install:

starter clutch drive gear
1

collar 2

washer 3
Refer to “CHECKING THE STARTER
CLUTCH”.
3. Install:

washer
1

O-ring 2 New

spacer
3
Lubricate the engine oil to O-ring.
INSTALLING THE GENERATOR
1. Install:

idle gear shaft

idle gear
1

washer

idle gear shaft bolt
2
LOCTITE
2. Install:

generator rotor and starter clutch assembly
1
ProCarManuals.com